Jump to content

GM 5.3L Avy HELP

Jengland
 Share

Recommended Posts

Jengland Enthusiast

Jengland

Posted
Posted

Hello,

 

I have a 2004 Avalanche, I have a no crank no start problem. 
 

turn key, everything goes away on dash, no crank. Let key go. All lights come back on. Re set passlock and that’s all good. Still no start. Nothing. Zero. Zilch

 

battery is fully charged days battery charger. You would think that it would start?

 

here is a pic of a wire I found just laying around not connected. Take in mind I just bought this today!

 

where does this wire go?  

9B86983D-8D55-4196-AE07-C769F4E4BC10.jpeg

richard wysong Senior Enthusiast

richard wysong

Posted
Posted

that's hard to say because it's not a factory wire. try taking a jumper cable and go from negative battery to the engine and if that doesn't work try going to the body. if that doesn't work and if it has a stud in the underhood power distribution box try going from positive battery to that stud. it sounds like a bad connection or bad cable but it's also possible it's got a bad starter

  • Like 1
Jengland Enthusiast

Jengland

Posted
  • Author
Posted

That was my whole problem.  That wire is the ground wire to firewall. Someone had left it like that. As soon as I grounded it, went over and started right up 

  • Like 1
richard wysong Senior Enthusiast

richard wysong

Posted
Posted

there should be a ground from the battery to the fender that may be  bad or missing or you may have a good body ground and a bad engine ground , it looks like someone added that wire to fix a problem that needs addressing before you get stranded some where

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Lower trims ( WT, Custom, Silverado ( aka LT )

      By newdude · Posted

      HD at the moment, are kinda their own deal.  How LTZ sells on those vs on 1500, there is a difference.   They are merging most of the mid trims on 1500.  LT, RST and LTZ are replaced by one trim, Silverado.  LT and RST are a BIG portion of sales.    Bad naming choice aside, the new Silverado trim will offer the spread of options that those three trims offered.  So expect to see things like the tech package for example, and memory seats.  And LT Trail Boss will now just be "Trail Boss" (formerly LT Trail Boss) but will offer content spread like the new Silverado trim will.  The press photos showed the Trail Boss (formerly LT Trail Boss) has access to Super Cruise now, which on the current truck was High Country only.       Here is the Trail Boss interior.  Memory seats and Super Cruise are present.  All things the LT Trail Boss it replaces, and the RST it was based on didn't get on the current gen.  You had to go to LTZ or ZR2 for memory seats, and High Country for Super Cruise.      
    • dennismc
      2021 vs 2026 handling (1500 X31 Sierra)

      By dennismc · Posted

      I installed a Hellwig rear sway bar on my 21 Sierra SLT, it made a huge difference on how the truck handles, no body roll, the trucks much more planted now. Not sure of the suspension differences between the 21 and 26,  if its body roll your having a sway bar will solve it. 
    • Old Bay
      frustrating P0446 code

      By Old Bay · Posted

      So a follow up and my fix. I found in online searches the live data to look at on a scan tool to verify the fuel tank pressure sensor was working.  It showed an spec number towards the lower end of the rang, but in spec.  Then while it was running opened the gas cap and the pressure should change.  It didn't change even a tiny bit.  The data for the purge valve said it was open...never changed. So then I measured the voltages on the plug for the fuel pressure sensor and they matched what it should be.  So local car quest parts had the sensor in stock...it was a bit of a pain to remove and an even bigger one to get it to actually go back in.  It helped to unbolt the driveshaft and bungie cord away from the gas tank to give a bit more room to work. So fuel tank pressure sensor in I cleared the code, and started it up.  I went to the scan tool's live data and... Eureka! The pressure number was different and fluctuated a bit.  So took it on a short drive and pressure number varied saw the purge valve go from closed to open and back to closed.  Drove it to and from work for roughly a week plugged in the scan tool no codes.  I took it in to get tested and passed.  In my state's infinite wisdom (oops meant greed), since I pushed the test with the maximum extensions I have to take it back in by Feb '27 to 'get it back up to date', then my next test won't be until Feb '29. 
    • newdude
      loose lug nuts

      By newdude · Posted

      Any grease on the stud threads of any kind?   Wheel studs should have NOTHING on them for proper torquing and so the nuts don't back off.     Are all of the mating surfaces clean?  So wheel, rotor and hub?     We've had plenty of trucks at work with that wheel, this is a first to me.  Makes me think they've got a lube tech putting anti-seize on all the wheel studs or some kind of grease, and they need to stop doing that.  To have 11 other trucks with the same exact problem.      
    • Flynlow
      2027 Chevrolet Silverado: Official Discussion

      By Flynlow · Posted

      I was a Chevy guy for years, then switched to GMC because I liked the looks better.  I'm actually thinking I like the Chevy looks better than GMC for the first time in a lot of years.   One thing I know for certain, the new GMC dash is hideous!  Chevy wins this one!  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...