Jump to content

Lock'er Down Security Products

jimbrown1

By jimbrown1
in Modifications & Accessories

 Share

Recommended Posts

jimbrown1 Enthusiast

jimbrown1

Posted
Posted

I apologize if this topic has been started, but I couldn't find anything when searching for Console Safe in the topics.

 

Lock'er Down has this console safe that allows users to keep the USB port but you must permanently remove the clip in deep pocket tray, and temporarily remove the file folder brackets on the side in order to install the safe.  Has anyone purchased one of these safes?  For the 2018 Sierra, do the file folder brackets in the console just snap in or are they held in with screws?  I couldn't see any screws last night when I checked, and they seemed rather tight when I pulled on them.  I haven't found any specific videos on the 2018 Sierra console, only the 2014-2016 where these brackets just snap in and out.  

 

Thanks for the help.  

BrianEB New Member

BrianEB

Posted
Posted

I have one of the safest in my 2018 Silverado and another in my wife's 2020. My truck came with it when I bought it, but I added it to my wife's truck, hers has the file folder brackets and they do have small screws that hold them in place. You have to also remove the rubber mat in the bottom of your console and 2 10mm head screws to add the safe, reinstall the screws one you get the safe in place to prevent someone from walking off with the entire safe. Save the rubber mat in case you decide to sell or trade for a different GM truck.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Core-Lokt
      Wiring Help, Please

      By Core-Lokt · Posted

      In the 6.6 gas thread, I added information in my fluid change thread about these gauges and temperatures. With very limited data, it so far looks like ~30 degrees difference between front and rear.
    • Core-Lokt
      Fluid Change Questions

      By Core-Lokt · Posted

      I know; crap pictures.   Anyway, as a finale of sorts to this thread, I had replaced both differential covers and since they had the capability of adding temperature probes, I did that. These are MaxTow analog/digital gauges with stepper motors. They'll flutter around like crazy for a moment and start at a nominal 100 degrees Fahrenheit.   I drove a 30-mile loop to the grocery store, averaging 70 MPH (as much as 80 to see if there was a quick spike in temperature. The air temperature is 102 (ambient ?). but the first pic is 7 miles into the trip. The second is getting back into the truck after leaving the store; differential temperatures dropped about three to four degrees in 15 minutes. The third pic in on the road to my house, about a mile away.   In that run, I saw a high of 150F on the rear differential, and 121F on the front. I'm sure a longer drive or towing will see higher than that, and when that happens, I can update the observations. 
    • KARNUT
      Vehicle Payments

      By KARNUT · Posted

      Naaa
    • Grumpy Bear
      Vehicle Payments

      By Grumpy Bear · Posted

      You don't want to become predictable now, do you? 😏
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Fully warm, coolant temp >194, closed loop.   Run time can be anywhere from just reached operating temperature to having driven 30+ miles.   The O2 chart (which is a feature I just discovered after reading) for the bad idle seems to be "most" of the time. For the little time I've been watching it (scanning and driving! watchout!) I can't seem to isolate any cause or condition yet.   It definitely idles rougher sometimes than others and so far what I've seen is the rougher idles are always rich. But not enough to set a CEL.   In other news I replaced the starter solenoid. Everything on this truck is such a PITA. Starter "snout" is mangled up with the torque converter inspection cover which is tangled up with hard cooling lines and the driveshaft. But I got 'er done without too much swearing...I just go into everything now knowing it's going to be a frustrating mess.   The starter solenoid replacement kicks off the next round of work: AC, injector rebuild, cat, exhaust. I'm just going to do it all. But first:   I don't know what my fuel pressures are. I can't definitively say the issue is the injector without first verifying fuel pressures and any leakdown. I "rented" a test kit ($199.99 at O'Really's ...intentional misspelling). They don't "rent" tools anymore, they charge you for the tool and then you return it when you're done. No joke. It is listed as a rental on the receipt but the guy told me there's no difference between renting and buying  now, you just return it when you're done and they refund the credit card. Mmmkay, whatever.   I will rule out fuel pressure issues (too much), and any leaking (that's how I'll know the problem is inside the intake). I think someone said the return line could be plugged or not flowing and that could cause high fuel pressure (and too much fuel being pushed through injectors). I'll cross that bridge if I get high readings.   As of now I'm ready to tear off the intake cover, extract the injector, and have it sent off to be rebuilt just so I can rule that out.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...