Jump to content

2018 Silverado Cargo 12v Plug

dye7barrel

By dye7barrel
in Modifications & Accessories

 Share

Recommended Posts

dye7barrel Enthusiast

dye7barrel

Posted
Posted

My suspicion is this question has been asked and answered. Just can not find exactly what I am looking for. 

 

Goal is to add a 12 volt plug to the bed of a 2018 Silverado. Trying to understand where the best location to bring power from. A couple years ago I added cargo lighting and connected to a plug beneath the bed by the spare tire. Wondering if one of the extra plugs would suffice. Would also prefer a plug that is not tied to accessory switch. In other words, hot at all times. 

 

As a bonus, if I could get 110v plug back there as well I would go for it. 

 

Thanks much for the help. 

mikeyk101 Senior Enthusiast

mikeyk101

Posted
Posted

I am not an expert but have stayed at a Holiday inn, LOL! But IMHO, I think a lot depends on what you are wanting to use the 12v power for in the bed. And I'm assuming you are looking for full time power or did you want switched power? If it's something that wont pull a lot of amps, there should be several places to grab power from. A multimeter should be able to find the power source you need. Personally, I think I would rather have a dedicated feed and just run wiring up to the battery. I would use heavy duty wire and maybe a sealed 2 wire cable to do it. Amazon has many choices but maybe stick to a 10 or 12ga wire because of the length. Make sure to fuse it as well and maybe install a waterproof connector close to your 12v outlet in case it needs to be disconnected in the future.

 

As far as 110V, it can be done but you will need to install an inverter. Again, you will need to decide what you plan on powering with it. If you have the 110v dash outlet and were considering tapping into that, that's a mistake as that inverter is pretty anemic. A dedicated one as well as a higher output one is the way to go. And if your new 12v outlet circuit is "beefy" enough, many portable inverters will just plug right into one and then you have both.

dye7barrel Enthusiast

dye7barrel

Posted
  • Author
Posted

Not looking to pull a ton of power. Mainly phone, GPS, and dog collar charging. And yes, full time power rather than switched. Knew there was a better term :) If 110v power requires another inverter then that is too much effort for this project. 

 

Sounds like I have two options:

1) Tap into hot wire from somewhere beneath the truck.

2) Bring new wire from battery to back of truck. 

 

Option 2 sounds more robust and would eliminate cutting of factory wires. I could also remove the bed plug and wiring in the future should the need arise. What else am I missing?

  • Like 1
  • 2 months later...
Neroado Enthusiast

Neroado

Posted
Posted

If you just need power back in that area and not inside the bed, you can just purchase a 12V plug adaptor that plugs into seven-pin trailer power port. There is a main line in that port that is always hot.  If I recall correctly, it's the larger gauge red wire that goes to the center terminal and it's on a 30Aamp circuit.  If you need the power inside the bed, you can easily access the seven-pin wires under/behind the bumper and run a line up behind the DS taillamp. 

 

Do your own research on which wire and terminal it is: it's been a while since I checked this out to plug in a macerator plug for my camper. I'm going from memory here.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined

  • Who's Online   1 Member, 0 Anonymous, 1,239 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • TrueBlue
      No Software Updates - Old Build

      By TrueBlue · Posted

      That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed, regardless of whether they are in warranty or not, or in the hands of the original owner or not. Why not updates as well, especially since some of those can be safety related also?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...