Jump to content

Instrument cluster guages stopped working

linda

Recommended Posts

linda Enthusiast

linda

Posted
Posted

Well, before i go tearing stuff apart tomorrow, i thought i might ask here first. I got into my truck today and started it up for the first time in almost a week. I looked down and noticed no guages registering at all. I turned it off and back on several times and nothing made a difference. Everything works 100% except for the guages....Tach, speedo, temp, tranny temp, batt, dont work. Odometer is working fine, D.I.C. is working and all lamps are working. Everything is fine except for the guages themselves. I looked through the fuse panels and found nothing representing JUST the guages. I found "A/C-INST CLUS-HAZ SIG" and one other that mentioned instrument cluster, but none that were for the guages only. Im hoping its not a PCM thing cause i do have a Westers PCM. Just seemed very odd. If no one has any suggestions i will look into it a bit deeper tomorrow. I just finished dinner so my motivation levels were down tonight, and i didnt feel like turning the furnace on in the garage this late.

rmk800ak Enthusiast

rmk800ak

Posted
Posted

Had the same problem it was -30 and just went to the stealer to pick up my truck the lot boy came back and said the gauges were not working truck had been there a week so i was like oh great but all we had to do is while running pull the fuse and replace that reset them i believe that the fuse you mentioned is the write one hope this helps

linda Enthusiast

linda

Posted
  • Author
Posted

Yup, that was it.....thanks. Just pulled out the un-blown "DIC" fuse (10a) and plugged it back in and all the guages came right back up. Truck was running when I did it.

 

thanks

THE BIGPUNN Enthusiast

THE BIGPUNN

Posted
Posted

same problem. my guages stopped working many times and would start again after sometime. mainly after truck sat for a few days in cold weather. i just had the guage cluster replaced by dealer. i thought there was a tsb for this.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      give me some tips to make my truck look better

      By asilverblazer · Posted

      Black bumper and the later years Z-71 style color matched grille.
    • fondupot
      Exhaust heat while towing!

      By fondupot · Posted

      You can install tailpipes that direct the exhaust sideways vs the OEM one that goes straight back. There are several on the market, do you own research. HOWEVER, you need to make sure the Venturi vents are still intact, otherwise it will throw a engine code. There is a sensor somewhere that detects back pressure on the exhaust. And if it doesn't collect the correct metrics, it will throw the truck into limp mode. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...
    • glenn27
      Different requirements for oil filters?

      By glenn27 · Posted

      // Thank you, also for your  response. More information is always good. This 2013 GMC is most likely my 'forever truck"-I'm 77 and retired...and truck only has 42K on it-very clean-so I try to keep it that way.  Tks again for your  response- glenn
    • smooth68
      Alternate wiring for Kicker sub with Bose system. (DO THIS)

      By smooth68 · Posted

      I started my install this weekend. Everything was pretty straight forward but I ran into one issue with running power through the firewall. The nipple grommet on my High Country already has a small harness running through it - has anyone else ran into this issue? And on the engine bay side, does the wire basically just penetrate the factory wiring boot? I did this on my '22 Trail Boss and it seems much easier but thats been a few years. My other thought would be possibly drilling a new hole adding a rubber grommet just to the lower left of the factory hole. Thoughts?   Has anyone used a T-harness off the Bose amp and obtained power from there? It seems a little odd that such a small amp needs 3 power leads

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...