Jump to content

1998 Chevy Suburban K2500 LT/Supercharged


Recommended Posts

Posted

This truck is loaded. From the factory it came with the 7.4 litre /454 cu. inch Vortec engine and electronic shift-on-the-fly 4WD. Leather interior, power everything and front and rear AC.

 

I bought it from a doctor in Potomac that used it on snow days and to tow his custom Corvette so with 80K miles this truck's just getting broken in. In addition to being totally optioned out from the factory below is a list of more modifications.

 

Whipple Supercharger running 6 lbs. boost.

 

Cowl induction hood.

 

Chrome front bumper ready for foglights.

 

Boost and Air/Fuel Ratio guages mounted on the A pillar.

 

Electric sunroof/moonroof.

 

2 sets of aftermarket wheels with Michelin LTX tires mounted.

 

Gibson cat-back exhaust.

 

Cradle and antenna for XM radio.

 

Navigation system.

 

Viper alarm with remote start.

 

Full set of Husky floor liner.

 

Trailer brake controller.

 

If the supercharger is too much for you or you want to use it on another project I have all the parts to put the truck back to stock. This includes the OE hood and front bumper and don't forget 2 sets of wheels and tires. You can see both sets in my pictures here: http://charlesstockton.com/images/98sub/

 

If you need a truck to tow or drive in the snow this is it. I've towed my 10,000 lb dual axle car trailer and it's like it's not even there and last winter I took it into a new housing development that hadn't been plowed. I stopped the truck on a driveway with a 35 degree up angle and 2 feet of fresh snow. Put it in 4 low and chugged right up the rest of the driveway. No problem.

 

Issues:

 

The computer that came with the supercharger stopped working. I determined that all it did was sense when the engine went into boost so it could activate another box that sent more voltage to the fuel pump so it would pump more fuel. My solution was to use a Hobbs switch and a Vortech FMU. I also installed a brand new OE fuel pump and sending unit. It works just as well and was a lot cheaper than getting the computer from Whipple. If you want the Whipple setup it's not a problem I still have all the parts.

 

Left front outside door handle trim is loose. I keep forgetting to go buy the part.

 

Little ding in the rear tailgate. The doctor did it not me.

 

I live in Shady Side, Maryland. Send me an email at [email protected] if you're interested.

$10,000 Firm.

Sale is for the vehicle as is and the buyer is responsible for picking it up.

 

Thanks,

Charles

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,860
    Total Members
    8,960
    Most Online
    HWN808
    Newest Member
    HWN808
    Joined
  • Who's Online   2 Members, 2 Anonymous, 1,036 Guests (See full list)

  • Latest Articles

  • Posts

    • Diesel $5.42 at the truck stop on the hi-way
    • I'm not sure if this should be a new topic, let me know if it's out of place. This my first post. Thanks 85077522 - AC Delco GM Genuine Parts Brake Master Cylinders. Anyone else had to replace this brake master cylinder yet. I didn't do any brake work, it looks like new parts and I've had the truck for about 4k miles, 119k total miles.  When it started to throw codes I did the calibrations with a bidirectional scanner and got the codes to clear but they came back so I did the routine; base bleed, automated bleed and final base bleed. All that with Bosch ES16-32N fluid (please look it up). That seemed to fix it but 100ish miles later it failed again so I ran the same process but with a pressure bleeder this time and got the same results, fixed for 100ish miles. The original fluid looked bad and I thought I got most of it out, it could've been the wrong fluid. The codes; P25A2, C05B0-00, C2A1B. I can get them to clear but not for long. The C05B0 indicates a leak in the front circuit (which is bone dry) so I'm thinking of doing the bleed process on that front again today and I don't know if that's taboo to just do the front but at this point it seems like it's worth the try anyway. The new master cylinder/module unit is supposed to get here today. But now I'm pretty much convinced this install is over my head. I've called several shops and some mobile guys that I know but this thing is like radio active material, scary wise. I did get 2 local shops say they should be able to do it, one says he has the SPS2 programing capability. And with the battery disconnected is there supposed to be pedal resistance, mine is to the floor, then if I pump it I can get some resistance. I had a panic stop prior to this issue which may have contributed from what I read. And on the first attempt to bleed and hydraulic test the scanner listed things to look for and one was any gaps between the pad and rotors which I did notice on the RF corner and I removed the outer pad (where the gap was) cleaned it and the hardware and didn't see a gap after that but will re-check it. I read that if pushing the caliper pistons back then you're supposed to open the bleeder so as to not push fluid backwards into the abs module or it will damage it. If that's true then that's also a possibility from the previous owner having the brakes changed before I got it. I'm using an XTool ip500 scanner. Any suggestions, questions and comments welcome. 
    • Next Friday will be my 6 week point from my right knee replacement.  The surgeon says it will be fine if I choose to drive after this checkup.  I know I could drive now but best to do as my surgeon (and my wife) tell me.  Richard compared being 62 to 72.  I remember when I was in my early 60's I was experiencing slow but regular decline in my mobility.  Thanks to good medical support,  i continued to fight the speed and spread of this decline. During my 60's I worked on non-surgical methods and just when I turned 70, my orthopedic surgeon recommended joint replacements.  In a little over a year, I had one shoulder and both knees replaced.  This hasn't been a terribly fun experience, but worth the discomfort as my future mobility health trajectory has reversed.  It is a treat to now be watching my mobility. balance and confidence steadily improve!
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...