Jump to content

Undercover Swing Case

MotoMedic

Recommended Posts

mipsco1 Enthusiast

mipsco1

Posted
Posted

Dont have one but was looking at one. I really liked the idea behind it but after seeing it in person it was just to small to make any sense.

TRCM Enthusiast

TRCM

Posted
Posted

This is the 1st truck I've had with no toolbox (it had a nice tonneau cover on it when I got it), and I'm almost ready to dump the tonneau in favor of storage . I used my toolbox before to store all kinds of stuff that I didn't want inside the truck, and right now, that isn't an option.

 

I can see where the swing case would be good for small stuff, but the gal size containers of oil I carry for my boat when I have a fishing tx just won't work in it.

welscher08 Enthusiast

welscher08

Posted
Posted

I had seen them last year and really wanted one, but for the price it just wasn't worth it. I have a cover and could use the extra storage space as well. They would be handy if cheaper.

Harvey Halabookie Enthusiast

Harvey Halabookie

Posted
Posted

I have one and I love it. It swings out between 90 and 180 degrees. It is the cable that holds the tailgate level that actually limits a full swing to 180 degrees. Even where it swings out to it is easily accessible.

 

I have a tonneau cover and the full size wheel well toolboxes won't fit under it. This case is designed well and I might even add one to the other side down the line.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,840
    Total Members
    8,960
    Most Online
    appletrav
    Newest Member
    appletrav
    Joined

  • Who's Online   4 Members, 0 Anonymous, 349 Guests (See full list)

  • Latest Articles

  • Posts

    • PhilB
      No 12v outlets in 2026 gmc Sierra

      By PhilB · Posted

      It is possible to add your own 12v outlet to your truck.  Check out this video:   I verified via GM Upfitters that pin 31 is the same on the 1500 trucks.  The wire is GM part number 84779405.   You can get the GM 12v outlet from Amazon  https://www.amazon.com/Genuine-Accessory-Receptacle-25774623-13549530/dp/B0F1H9YRGF EWAY 12 Volt Power Adapter for GM   https://www.amazon.com/EWAY-Chevrolet-Silverado-Cigarette-Ignition/dp/B0915RRW6Q/ref=sr_1_1?   I just haven't figured out a good place to put the 12v outlet in my truck.   Some people are getting USB-C to 12V adapters  https://www.amazon.com/WYMECT-Cigarette-Lighter-Socket-Adapter/dp/B0F87WNQKB/ref=sr_1_1_sspa? Not sure if they provide the correct amperage that a device like a tire inflator would need.  
    • Core-Lokt
      Wiring Help, Please

      By Core-Lokt · Posted

      Thanks; I looked there a few minutes, and I think I can find something. I really never looked there, as I thought it was stuff like PTO/aftermarket bodies/accessories like snow plows.
    • newdude
      2 speed transfer case optional now?

      By newdude · Posted

      This is a 1/2 ton thing ONLY.  All HDs 2020-2026 have the two speed transfer case, with Autotrac as an option.     1/2 tons 2019-2026, regular 4x4s come with a single speed case (no 4LO!), and trucks with Z71 ordered, or all Trail Boss trucks come with the 2 speed case.  2 speed case is also an option on WT, and is also standard on High Country.  
    • newdude
      Different requirements for oil filters?

      By newdude · Posted

      2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.          That all said...   Your 7045 Napa filter is the PF63 equivalent, with 22psi bypass.  You are already using the higher bypass pressure filter.  You CAN keep using it, you don't technically have to use it though.  
    • Grumpy Bear
      Different requirements for oil filters?

      By Grumpy Bear · Posted

      Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...