Jump to content

2012 Silverado CC 6.2l with $1,100 to spend on....


Recommended Posts

Posted

Ok everyone I have $1,100 to spend what should I spend it on? I guess I really only need help allocating $600 because number one on my list is the Auto cal from BB.I have RC 2.5" front and 3" Rear blocks, tinted front windows K&N drop in 6.2L hood decal removed the air dam and also cut the exhaust tip and put a 4" tip on it. So help me out what Should I get? Here is a picture of how it sits now. I would like to get an exhaust or just muffler but just not sure of what I want because I don't want the drone and I do a lot of long driving so I don't want it annoying loud while cruising.20130202_145251_zps443cb090.jpg20130202_145137_zps7208f242.jpg

Posted

DuHa rear under seat storage box.

WeatherTec floor mats.

Leave the factory exhaust alone.

Posted

Oops left something out, I have weather tech floor mats front and rear...

Posted

Air raid mit (100-120$)

 

 

 

 

Ryan

 

 

Posted

Where do you find it for 100-120 price range, cheapest Ive found was on amazon for $128.00

Posted

DuHa rear under seat storage box.

WeatherTec floor mats.

Leave the factory exhaust alone.

 

The DuHa fits so cleanly under the rear seat, I forget it's there.

Posted
Where do you find it for 100-120 price range, cheapest Ive found was on amazon for $128.00
Check summit racing Ryan

 

10% downpayment on a supercharger :thumbs:
A SC isn't $11KRyan
Posted

Great Ideas although I think the SC is out of my range.... So far Im thinking the Auto Cal and the Air raid mit. Doesn't BB carry these too?



Posted

I would buy new tires, sell the duelers to offset the difference.

 

Don't see the point to get rid of good tires (as in tread left) plus I already budget for tires on my vehicles.

I would buy new tires, sell the duelers to offset the difference.

Posted

From what I've seen, and on my dads Silverado, the duelers do not perform great compared to other tires, plus they have a low life for mileage.Most factory tires are like that.

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,840
    Total Members
    8,960
    Most Online
    appletrav
    Newest Member
    appletrav
    Joined
  • Who's Online   0 Members, 0 Anonymous, 279 Guests (See full list)

    • There are no registered users currently online
  • Latest Articles

  • Posts

    • This is a 1/2 ton thing ONLY.  All HDs 2020-2026 have the two speed transfer case, with Autotrac as an option.     1/2 tons 2019-2026, regular 4x4s come with a single speed case (no 4LO!), and trucks with Z71 ordered, or all Trail Boss trucks come with the 2 speed case.  2 speed case is also an option on WT, and is also standard on High Country.  
    • 2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.          That all said...   Your 7045 Napa filter is the PF63 equivalent, with 22psi bypass.  You are already using the higher bypass pressure filter.  You CAN keep using it, you don't technically have to use it though.  
    • Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉
    • Probably not their first rodeo, so it should go as planned most likely.  Typically the service manager or tech doing the swap will put some seat time to shake it down after they get it all put back together.  We usually put 50-100mi before we hand them back so if something happens, its not after you get it.  A coolant leaks, oil leaks, a ground left off or loose, vibration, etc.     The new engines so far have been good?  There's been a couple that have popped out there again (the replacement engine) but most have been okay.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...