Jump to content

Climate Controlled Seat Troubleshooting


Recommended Posts

Posted

Hey ya'll. I have got a couple of quick questions about the climate controlled seats. I have a 2009 Sierra Denali with the heated/cooled seats, and my driver's side seat isn't working. The passenger side seat works just fine, and the controls on the door work fine as well. All of the lights illuminate and indicate that all the settings are fine. I checked out the connectors on the seat climate control module, and I didn't notice any carbon buildup or damage. I'm at the point where I have to start swapping parts or shooting wires I think. Does anyone have any wiring diagrams or pinouts for the seat climate control, or any other suggestions for getting everything working again?

Posted
I saw this TSB related to inoperative seats - maybe take another good look at the CCSM contacts, clean them, check pin fit closely?
I don't have any diagram for the CCSM itself, just the pwr dist schematic from the fuse block to the control.
#PIT4609B: Heated / Cooled Seats Inoperative - (Dec 6, 2012)
Subject: Heated / Cooled Seats Inoperative 999999995.gif Models: 2007-2011 Cadillac Escalade Models 2009-2011 GMC Sierra Denali, Yukon Denali 2009-2011 Chevrolet Avalanche, Suburban, Tahoe (LTZ Models Only) With Heated And Cooled seats (RPO KB6) The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition/Concern

Some customers may comment that the heated or cooled seat feature is inoperative for either the driver or passenger front seat. The cause may be a poor connection at the Climate Control Seat Module (CCSM) C1 pin E circuit 4740 (07 model year) or X1 pin E circuit 4740 (2008-11 model years).

Recommendation/Instructions

Closely inspect CCSM C1 pin E or X1 pin E for proper pin fit. Also check for any distortion of the connector housing or CCSM that could cause a poor connection. If any distortion is found, replace the CCSM and connector.

Posted

I didn't see anything at all that would indicate a poor connection. I didn't see any recessed pins, damage to the connectors, burn indications, or buildup that one would expect would lead to a problem. I will check again. Does anyone out there know which pin on the Driver's seat these wires lead to?

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.3k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,732
    Total Members
    8,960
    Most Online
    user087
    Newest Member
    user087
    Joined
  • Who's Online   4 Members, 1 Anonymous, 829 Guests (See full list)

  • Latest Articles

  • Posts

    • This doesn't look like a GM truck. Not needed on a HD truck
    • It varies a ton around me. Some places are still at $5.00 or higher and others are way down into the $4's.   Offroad diesel was $4.02 at the one station I passed today.
    • So after reading the reveal from Chevrolet, I kept asking myself...why did the trim levels change?   Here are the official ones:   Work Truck (WT): The quintessential fleet truck, built with durable, easy-to-clean interiors for commercial or utilitarian use. Custom: A stylish, road-oriented trim that adds a more refined appearance, standard dual exhaust, and modern exterior styling. Custom Trail Boss: An entry-level off-roader featuring a 2-inch factory suspension lift and 34-inch mud-terrain tires on a budget. Silverado: Serving as the new base consumer truck (replacing the previous LT trim), it comes standard with the Z71 off-road package when equipped with 4WD. Trail Boss: Steps up the off-road hardware with the 2-inch lift, 34-inch tires, monotube shocks, an exclusive off-road hood, and more premium interior options. ZR2: The flagship off-roader. It boasts 35-inch mud-terrain tires, Multimatic DSSV dampers, front and rear electronic lockers, forged carbon-fiber interior accents, and an available hardcore Bison Edition (co-developed with AEV). High Country: The pinnacle of luxury. It replaces bright chrome with modern satin chrome, 22-inch wheels, premium leather, real wood interior trim, a panoramic sunroof, and an exclusive front-passenger touchscreen. As others have stated, why would you want a Silverado - 'Silverado' - wth?? LT needs to remain!!!   Also, there will no longer be a dedicated Z71 model.  All 4x4 trucks will have the Z71 package. Carplay is also something that cannot be removed.  Hopefully it will remain.     I am excited about the 5.7L V8 (350 C.I.D.)  Old school Chevy power.  My only concern is whatever version of AFM/DFM cylinder deactivation.  Too bad that isn't an option a buyer can choose to have or not.   I will definitely be stopping by my local dealership when these trucks start showing up.
    • I haven't seen diesel for less than $5.30 anywhere in my area
    • The not as clean as one would assume theme with the new engine oil, that reminds me of comments over the years with mechanics not always being so on board with filling an oil filter, not from the center anyway due to that typically being the clean side of the filter, danger of some contaminant falling into the filter if not careful but the realization now that the oil may not be as pure as one had assumed it would surely be. Yes it would be possible to fill from the small holes but that means messing with something to prop open the anti drain back valve if the filter is so equipped and not damage that valve in the process. Me, I have hardly ever prefilled an engine oil filter however I have prefilled diesel fuel filters with a filter on a fuel bulk tank and for anyone that has messed with diesel engines with filters and units that have a limited or no way of priming them, putting on a dry filter is a bad day to say the least with those crappy systems. But anyway back to not so clean engine oil, indeed perhaps its not so bad after all that I have not made a practice of prefilling oil filters.    As Grumpy Bear commented on keeping things clean, that I really have to wonder what the typical practice is at a dealer or any other shop that changes engine oil, do they make sure to wipe or wash off the oil plug and certainly if it fell into some gunk or onto a dirty floor, or that they wiped the filter mounting flange and didn't go and use some dirty rag and end up adding dirt to the inside of the head of the filter mount. Or be careless in how they stored or handled the new filter and if they were bumping into items under the vehicle with the filter opening facing up and having dirt drop right into the filter and if so right into the threaded center that is on the clean side. The top side, did they clean away the built up gunk that may be around the filler before removing the cap or to be really careful at that point that something right close to the filler hole that was hidden under the caps flange won't fall into the engine. Or did they clean the funnel or was that just laying there covered in oil from the oil change before and dust kicked up from sweeping the floor stuck to the oil and now that will go running into the next persons engine due to just not cleaning the funnel as "they won't know anyway" attitude as that young guy is more worried about taking a break so he can go outside and smoke a joint. Just random points that came to mind when I think about what some hired personnel may do that the shop foreman has no idea of or perhaps the whole attitude of some shops may be "eh ... who cares, they will never know the difference anyway".  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...