Jump to content

C load or E load BFG KO2 for off road

2004BlueBurb

By 2004BlueBurb
in Tires, Wheels & TPMS

Recommended Posts

swathdiver Senior Enthusiast

swathdiver

Posted
Posted

I didn't want to forget so I just checked my LF front with a flashlight and you are right, 2 ply!  The tread is actually 5 Ply.  Oh well.  I learned that the actual plies for each rating is no longer valid, just as long as the tire meets the requirements for that load range, which makes sense.  The Part number for the tires on my truck is 66255.

 

The ride is very nice, not Ford truck like.  The truck handles very well and whips around like a car.  I went through a muddy parking lot in 2WD effortlessly this morning that would have sunk a car.  My only gripe is the amount of mud thrown onto my running boards, now I need mud flaps!  The tires can support the maximum weights at just 42 psi and the truck doesn't move an inch going 80 mph through rainstorms, the sipes are very similar to the Radial T/As that we used to run on our Buicks way back when and we did 80 mph in the rain with ease in those cars too.  That being said, the Cs will handle your stability and weight requirements but can't say about the rocks.  

 

We should check in to this thread once in a while to let each other and the folks out there know how they're wearing and doing, how many miles we eventually get out of them before replacement.  I'd like to see at least 50k and 60k would be really nice.  

  • Replies 30
  • Created
  • Last Reply

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,978
    Total Members
    8,960
    Most Online
    rayredbone
    Newest Member
    rayredbone
    Joined

  • Who's Online   4 Members, 0 Anonymous, 318 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      AFM Experience

      By Grumpy Bear · Posted

      Question @diyer2 on this line if you please. Are you saying the shudder is the system turning on and off at the frequency of the shudder? Guess I'm asking if you are saying you have seen it do this with the bi-direction scan tool in graph mode? If so have you been able to discern the 'trigger'. Something is telling to cycle rapidly.    My truck just started doing this recently. 197K on the clock. My response has been M5 anything under 55 mph. I treat it like a lugging stick shift. Gear down and let it spin a bit. Engauge M5, then tow mode and then M6 lets the trans stay in 5th but the AFM is active. Smooth like Skippy.    My thought was that as a machine ages the friction gets lower and as the system is load based, the lower friction would allow it to turn on at ever lower rpm until it reaches the lugging point. And yes I am ignorant of any minimum rpm requirement for the system. If you know that would be useful information.    As you know I run a Scan-Gauge II which allows me to watch the On/Off of the signal to the VLOM. While in the shudder mode I'm not seeing is cycle at that frequency or at all for that matter outside the triggers @newdude posted a few years back. Now is it possible that the refresh rate isn't fast enough to catch it? Maybe. It is why I asked my first question about graphing and trigging parameter.     As we have observed from members here the failure point is all over the map miles wise as you note yourself in your opening post. That by itself begs a few questions like fellows that comment on these lifters failing even after the system has been disabled. Long after. 😬   https://www.enginelabs.com/news/tech-tips-replacing-ls-active-fuel-management-lifters-with-melling/   The Gen5 lifters operate the same as the LS versions. In fact they are the same lifter.    https://www.enginelabs.com/tech-stories/sorting-out-gen-v-lt-lifter-failure-with-a-simple-valvetrain-fix/        
    • SwitchBladeSierra
      14-18 Sierra 1500 Heated Steering Wheel Help

      By SwitchBladeSierra · Posted

      UPDATE 2: Steering wheel control backlights and control of the cluster can supposedly be achieved by adding a wire to pin 20 of the cluster and tapping it to pin 2 of the main clock spring harness. I'm going to give it a shot - will update  
    • newdude
      Seems to be Missing a lot of Updates

      By newdude · Posted

      GM Global A pickups 2019-2022 can do OTA programming for the radio.  GM VIP (GM Global B) can do OTAs for almost every module on board.  So a 2022.5 and newer pickup can do OTAs for recalls like the 2.7 fuel flow recall.  EVs get OTAs that improve one pedal driving, radio issues, HVAC issues, updated battery management software, etc.     So age of the vehicle/what GM electrical platform its on will alter what amount of updates can be pushed on OTAs.  
    • Blade8971
      Upgrade to a 2026 AT4 with the 3.0L Duramax

      By Blade8971 · Posted

      Thank You.   So far my new ride is making me look like a genius for going with the 3.0L, as my first fuel refill occurred over three weeks from when I took delivery.  This engine combination is very amazing.  So far no issues and had not done a regen yet.
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      I am curious as to how much fluid you put back in the transmission ( assuming you had replaced the filter to compare to my findings ) and then went through the process of warming up the trans before pulling the check plug to drain out the excess and if you measured how much came back out.    I just found it surprising that some claimed a certain amount less fluid being put in and then draining some back out. The attitude of the truck as per if the surface is level and how the trucks stance is would make quite a difference since the check plug is right at the front of the transmission. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...