Jump to content

WEIRD LEFT INDICATOR FAILURE

xIIPHOENIXIIx
 Share

Recommended Posts

xIIPHOENIXIIx Enthusiast

xIIPHOENIXIIx

Posted
Posted

So couple days ago my left rear turn/brake started acting up. I get the left rear indicator failure message. The bulbs are fine, I checked the fuse and its was good too. I went ahead and got a new fuse and bulbs and installed them, yet nothing. With a tester I tested the power coming from the BCM thinking it went out but no power comes out. I tested the fuse also and it lights up/flashes when the turn signal is on or step on the brake. I checked the entire harness and there were no signs of cuts. Here is the weird part this shit will work when it wants. It can be fine for two days and then the next day it wont work and will last until it decides to work. So II was thinking it was a relay when it gets hot it wont work. As it cools down it will start working again until it heats up or bullshit like that. That's my only solution as of right now. Does anyone know what relay it would be? OR WTF is could be? The right side works fine all the time. I shared a pic of the wiring diagram to give a better example of what I'm saying. 

 

THANKS FOR ANY HELP!!!

HELP.png

BigBadSierra Senior Enthusiast

BigBadSierra

Posted
Posted

It may be a bad socket connector on the end of the harness Had an issue like that on a 05 Colorado. Had to replace them..

  • 1 month later...
Donstar Senior Enthusiast

Donstar

Posted
Posted

The first thing that came to my mind was a faulty ground.  It sounds to me you have already gone above and beyond the steps needed for a DIY solution.  Go to a gm service facility that you trust and get it checked out.  You  may be missing something simple and obvious to someone else who is able to physically see your vehicle.

A good example of my advice recently applied to me personally.  Last week I was out in my brand new Winnebago TT and  I could not get the park's cable to work for my TV.  I asked for help on a Winnebago forum and traced all of the wiring.  I even phoned an RV service department.  Two days later I explained my problem to the park owner who was very knowledgeable on the topic.  The first words out of his mouth were, "you need a cable box."   This sounds obvious now, but it was totally out of my realm of consideration that you'd need a home-style cable box at an RV hookup!  Nobody on my RV forum or at the RV dealership even hinted at a cable box!

  • 11 months later...
David Schneider Enthusiast

David Schneider

Posted
Posted

Yeah dude I'm having the same problem with my truck but now my tail light went out all together with two brand new bulbs so something in the wiring or my sockets. Cuz when I replace my top tail light the sockets were so corroded I couldn't get the light bulbs out but now left turn signal failure. Is on all the time.  So it's got to be somewhere in The wiring.  Or bad relay some where

  • 4 years later...
OneFatCat New Member

OneFatCat

Posted
Posted

I have been battling this issue and found that the problem is with the metal contacts on the bulb itself. They lose contact over time. Take the bulb out and bend the two natal contacts out slightly and then reinsert. I hope this works for you too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,924
    Total Members
    8,960
    Most Online
    KirbyCo
    Newest Member
    KirbyCo
    Joined

  • Who's Online   3 Members, 1 Anonymous, 1,442 Guests (See full list)

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      I will be doing that for sure, but I need to solve who has/ where I can find a bidirectional scan tool that will support OBD 1.5. I'm kicking myself because I ebay'ed a Snap On MT2500 that I didn't think I'd ever need anymore. D'oh!! I'd rather not buy another, so I'll contact a few local shops to see if they have one and how much they'd want to do the procedure. I'd rather have the ability to do it myself... I wish there was a modern tool that could do it all, but I'd have no idea what to buy.   The theory with the pulled timing is that it mimics a rich condition. The delayed spark causes incomplete burn and the O2 sensor picks up low oxygen levels. That's interpreted as a rich condition so the PCM pulls fuel and that shows up in the deeply negative fuel trims.
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      An ultra wealthy man had the most beautiful daughter. But, there was a problem. Everything she touched would melt in her hands. No matter what, Metal, Wood, Stone. Anything she touched would melt. She could not feed herself. Because of this, men were afraid of her. Nobody would dare marry her. Her father was despaired. What could he do to help his daughter? He consulted doctors, scientists and anybody who could solve this problem. Finally one of them said, "If your daughter touches one thing that does not melt in her hands, she will be cured." He was overjoyed and came up with a plan. The next day, he held a competition. Any man who could bring his daughter an object that would not melt in her hands would be given billions of dollars to marry her. Three extremely intelligent and handsome young men took up the challenge. The first brought a very heavy steel rod, But alas, when the she touched it, it completely melted in a matter of seconds. He sadly went away. The second brought a beautiful diamond, knowing diamonds were one of the hardest substance in the world and would not melt. But alas, once she held it in her hand, it melted. He too was sent away disappointed. So now, there was one left He was very nervous & sweating. He approached the daughter & said, “put your hand in my pants pocket and feel what is in there." She did exactly what he asked. She felt something very hard. She held it in her hand, squeezing it as hard as she could. It did not melt & remained extremely hard. Her father was overjoyed. Everybody was overjoyed. She was finally cured. Nothing never, ever melted in her hand again. They married and they both lived happily ever after, raising a wonderful family. Question: What was in the the groom’s pants pocket??? Answer below ↓ M&Ms of course! They melt in your mouth, not in your hand. What on earth were you thinking?
    • asilverblazer
      Wow I'm in a pickle. (Broke down truck) and a story.

      By asilverblazer · Posted

      There's a bunch of tea leaves that you've read, but in any case the delayed timing is unusual. Not sure how that relates to the rich at idle vs. 'normal' while driving.   If you're in this deep, might be worth investigating, and re-learning the sensor. What have you got to lose? Plus, it properly fixes the timing cover leak.
    • asilverblazer
      Wow I'm in a pickle. (Broke down truck) and a story.

      By asilverblazer · Posted

      The only problem I have seen this cause is longer crank times. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Injector is being sent off today for rebuild and I estimate I'll have it back in 10 days or so.   It may not be the injector...of course...now that I've torn down the intake again. But, let's rule out the injector and replace those spider legs that have been almost rubbed through.   The truck has always had negative timing and I'm reading "normal" timing at warm idle should be +16 or so. I'm negative 16 to 25 or more, and it's always been like that since I bought it.   A light turned on upstairs last night in the old noggin. Rare, I know...   This will be wild, if it turns out to be the cause!   In 2001, according to the old service documentation, the muffler was replaced. Why? I have no idea, it wouldn't have been rusted through by then. But they did a crappy job.   In 2019, another shop replaced it and noted the prior install was poorly done on the work order. "Exhaust system vibrates on crossmember". Except...I guess they just left it be? I believe the husband, the couple who were original owners, had passed by then. Maybe she said it's just not worth it to have the exhaust system fixed and declined repairs. Very few miles were driven between 2019 and 2025.   The exhaust system vibrates heavily on the crossmember and you can feel it and REALLY hear it, even today. Not always, but at idle, it gets going pretty good sometimes.   What if....   ....What if that's enough to trigger one or both of the knock sensors? Could it be tricking the sensors into sensing knock, so it's pulling timing aggressively? Pulling timing heavily means it's firing after the piston reaches full height which means incomplete burn which means the O2 sensor is sensing a rich condition, which means I've been chasing my tail, and what I thought was an inconsequential problem (janky exhaust) has been THE issue for this truck for 25 solid years?   That would be wild. Maybe it IS wild.   The service documentation thereafter, for years, shows visits for rough idle, replacing O2's, replacing the cat, replacing plugs and wires, a misfire condition, like they could never solve the issue. The injector has been replaced 4 times in 80k miles, that's just crazy.   The secondary theory....   The engine has clearly had a leak at the front seal for a very long time (the greasy trench...). I think the truck changed hands quickly ~2025 because there's Napa receipts from someone I don't recognize in the ownership history. They apparently replaced the timing cover seal, and they did a terrible job. There's RTV smeared all over and the leak I had reduced to a weep by snugging the front oil pan bolts is now a leak again.   HOWEVER....I read about replacing the crankshaft position sensor. Any time the ckp sensor is disturbed or timing cover is removed, the truck requires relearning, and that can only be done through a bi-directional scan tool. Skippy with the RTV probably didn't do the relearn procedure is my guess. His scan tool is lost in a pile of RTV goo somewhere.   So, it's very possible the sensor has been disturbed and the truck is just running on the old learn data but not setting a code for anything. The distributor has since been replaced and so has the camshaft position sensor, so all bets are off for that thing.   In the theme of one step forward, two steps back, I returned the accumulator for the AC. The gal I've been working with at O'Really's has been great. She refunded it under manufacturer's defect and we compared it to the replacement I ordered, and sure enough, the replacement is machined very differently (and a gauge actually fits on it!).   Got it home, installed it, started vacuuming it down.... and I couldn't get good vacuum.   The high side service port, where I replaced the old GM ball valve suspecting that was a source of the previous leak....well, I've clearly exposed whatever pre-existing crack in the line where the service port is welded, and made it much worse. Blessing in disguise? Except there goes another $25, now I'm waiting for a replacement AC line.   In 10-ish days ALL the parts will be here. Rebuilt injector, new exhaust system, new cat, new high pressure AC line.   Oh, did I mention the squeaking ISN'T coming from the AC pump? The truck still squeaks when started, and there were words after I started it with the new AC pump installed. But, there was more to replacing the AC pump for just a squeak. A truck with good working AC is something of value, for the comfort alone.   I've ordered a new harmonic balancer because, 30 years is a good run for one of those. Rule it out. The squeak may be something more sinister, though. I'm worried about that ckp sensor and if it was shimmed correctly, or if the timing set was installed correctly. The squeak may be coming from UNDER the timing cover.   At this point, once I get it put back together, I'm thinking I'll take a 50 mile victory lap and then promptly put it up for sale. This truck is cursed. Betty, from beyond the grave, doesn't want anyone messing with her Blazer. Or maybe she's getting revenge for 30 years of shop visits with that thing.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...