Jump to content

Fittin 33s

KenL12

By KenL12
in Modifications & Accessories

Recommended Posts

KenL12 Enthusiast

KenL12

Posted
Posted

Anyone know if you can Fit 33s on a 14’ Silverado 1500 with 2.5” leveling kit only ? Or what the biggest tire you can ?

J_Brown Enthusiast

J_Brown

Posted
Posted

90583bdcad8defad194954d8bc257a07.jpg

33X12.50
20X10
-12 offset
2 inch level kit
Runs very little and I mean little only on full turn and depends on how my truck is sitting (level ground or whatever)


Sent from my iPhone using Tapatalk

KenL12 Enthusiast

KenL12

Posted
  • Author
Posted

What kind of level kit ? And how much ride / steering difference do you notice ?

J_Brown Enthusiast

J_Brown

Posted
Posted

Moto fab level kit, and not much at all man. Of course it’s going to be louder cause of the noise but still drives smooth as it did when It was stock, it least to me it did.


Sent from my iPhone using Tapatalk

KenL12 Enthusiast

KenL12

Posted
  • Author
Posted

 Set nice man , thanks for the info .. been waiting for my tires to wear out before i did this 

  Love the way it rides so i was kinda hesitant.  But I’m going for it. 

Thanks again 

TX LIMO Enthusiast

TX LIMO

Posted
Posted

I run a Motofab 3/2 with Falken Wildpeak AT3 33-11.5 on stock 17s. No issues noted so far. Been running it for just about a year now. fa3e56390a5d577495a1f2403f6bb108.jpg


Sent from my iPhone using Tapatalk

Michael71009 Enthusiast

Michael71009

Posted
Posted

Leveled with Bilstein 5100s, and an added half inch strut spacer. 305/55r20 tires with a 20x10 -18 wheel. Had to trim part of my factory fender flare inside the wheel wells. Still minor rub at full lock backing into my driveway. 4d41f30d32ca08e64deb286121905d6d.jpg

Sent from my SM-N950U using Tapatalk

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Core-Lokt
      Fluid Change Questions

      By Core-Lokt · Posted

      I’m going off the instructions.
    • Grumpy Bear
      Grumpy Bears 2015 Silverado 2WD

      By Grumpy Bear · Posted

      My expectations are a bit higher.    No faded paint or dry rotted plastic/rubber. I use a dressing and a ceramic sealant. No hazy headlights.  No door dings. Small dent in the front bumper. All rock chips repaired. No brush scratches. No windshield chips. No fender benders. Limit damage due to a proactive plan the included ceramics and PPF and prompt attention to any exterior issue. NO RUST. Stays out of the salt and had the rear wheel wells Line-X coated as well as the bed which has a bed rubber and has been under cover since before I bought it. Washed and detailed regularly. Rex chewed up the tow button, got whacked and the button replaced the same week. He's leaned his lesson. If I can train a dog the kids are easier.    All suspension is original save the King Shocks I installed very early on. 50 years ago dad told me a good shock will keep the screws in the dash tight and the front end mint. He was right. Everything within new spec yet, tight and aligned well several times. Coolant system is OEM save the modifications I made early on. Not a single leak anywhere on this machine. (Did repair an intake leak on #4 during the HPFP replacement.) The injectors I replaced didn't need to be. They checked out great. One of those, while I'm in there with the manifold off and the fuel rail apart things.  Not a stain or abrasion one to the upholstery. Have kept is covered since new. Never had a carpet, it's a work truck but the carpet squared I laid on the floor have keep the factory rubber liner MINT. Ceramic wind tint helps preserve the interior.    Original BRAKES with 60%+ left of the pads and rotors mic excellent. We just did a full preventative brake service. Disassembly, clean inspect including measurements, lube, Dot 4 power flush including ABS system.    OEM battery. OEM vacuum pump. In fact the only things not OEM are a pinion seal the high side pump and injectors and a small plastic shield around the starter. All hoses/belts etc.. are still in service and doing well. Original tires lasted 125K and had I known some additional details would have made it to 150K with legal tread. (Date out is six years, not 5 and Continental says they are good for 10 so I pulled the trigger to early)   I never let my children or grandchildren run the show. Feet on the floor and hands in your lap. Dog gets a pass.    A truck is a machine the gives you back whatever your willing to put into it. Same as a computer or a butter knife. I use a shovel but I scrap it, hose it off and oil it when I'm done with it. My original spade I've had 60 years.      Set the bar higher...you spend less money. No, before you ask, I have spent a fraction of the cost of a new truck in my entire maintenance program including disposables, filters/fluids etc.     
    • Atlas
      Gas Prices

      By Atlas · Posted

      5.48 regular still here at Kroger. Stations here aren't getting the memo but the owners are probably tired of programming prices up/down with every headline and futures gyration.   WTI Crude is over 80 again but seems mostly unfazed after the exchange of fire in the Middle East over the weekend and ceasefires falling apart. 🤦‍♂️ Enough already...    
    • newdude
      Looking at ordering a '26 WT because I want a std cab, std bed

      By newdude · Posted

      Keep an eye on it with them.  Did they give you an order #?  Did they actually have allocation for one?   I double checked the dates for 2026 regular cab 1500s for Chevy and GMC, the last dealer order submission date was April 30th.  
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      5 miles away at Marathon regular E-10 87 16 $4.87 😱 25 miles away at Shell V Power Nitro+ 93 for $4.89.    In general not hard to find regular for $3.99. Seems everyone isn't getting the same memo. 😏

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...