2019 Silverado Sun visor removal

Christian Welch · October 21, 2019

Hello, I have a 2019 Chevy Silverado and I am wondering how I can move the one little clip from the sun visor. I’m a volunteer firefighter and I am trying to install my visor lights on there but I need to remove that clip to see if I can slide my bracket behind it. Photo attached is the clip thing I’m talking about.

ChrisM73 · October 24, 2019

I am having the same exact problem. I bought a Feniex bar with the vehicle specific bracket and they claim it fits. I even spot with one of their installers/engineers today and he said he has gotten the bracket between the clip and the headliner. I laughed...

ChrisM73 · October 24, 2019

Christian, I finally got it! Brute force wins. If you rock it side to side, and pull down you will loose it enough to side the bracket under. It eventually will come out.

See this video. Yes, it is the wrong model year, but it is the same design on the new 2019/2020s.

Onto the next challenge: bending the brackets to fit the new angle of the windshield...

Christian Welch · October 26, 2019

Okay thank you Chris. Ill have to give it a try!

oldmann · October 28, 2019

I would love to see how that bar looks inside and working outside. I need a bar that goes from all amber to all red pretty bad. Construction, fire department

Christian Welch · October 30, 2019

I finally got my visor lights up. I loosened it just enough to be able to slide the bracket under it. It took some force though lol but I got it.

Steve Martin · October 30, 2019

3 hours ago, Christian Welch said:

I finally got my visor lights up. I loosened it just enough to be able to slide the bracket under it. It took some force though lol but I got it.

Looks good. I've got my visor lights ready to mount. Any tips? Mine are Feniex.

oldmann · October 30, 2019

Very nice. What controller are you using mini 4200? I have to get a bar in the rear too. Maybe a couple singles in the rear side windows at the top for side warning.

Christian Welch · October 30, 2019

I’m using the Elemental 40 visor light bar from extreme tactical dynamics. They are very bright and well built but the customer service is trash https://www.extremetacticaldynamics.com/products/elemental-40-tir-led-visor-light-bar/

ChrisM73 · November 3, 2019

On 10/29/2019 at 8:15 PM, Christian Welch said:

I finally got my visor lights up. I loosened it just enough to be able to slide the bracket under it. It took some force though lol but I got it.

Looks great! I finally convinced Feniex that I have the wrong brackets. That only took 2+ weeks of calling and emailing. Now I just have to wait for the new ones.

CNADN SIERRA · November 23, 2019

Would you be able to show an interior pic of mounts?

Michael Conti · December 22, 2019

Hey, I am having the same issue, is this the brackets they sent you for the lights? I just got the Feniex Geo bar, and choose it due to the vehicle specific brackets.

Edited December 22, 2019 by Michael Conti

Michael Conti · December 22, 2019

5 minutes ago, Michael Conti said:

Hey, I am having the same issue, is this the brackets they sent you for the lights? I just got the Feniex Geo bar, and choose it due to the vehicle specific brackets.

Steve Martin · January 2, 2020

Yes. That's the feniex bracket. I'll try and grab a pic of mine. I have the fusion. It was extremely hard to get in place, but doable. You can take the screw out, be very careful with opening the tab for the screw, but then there is no obvious way to tilt or maneuver anything to get it to loosen up. I barely was able to inch the bracket under and into place. I would love to know how the visor clip is removed. Would make it so much easier to install. Hopefully you got past this by now, but I'll snap a pic and post if I can. The other bracket for the other side of the visor is easier to figure out, but a bit complicated still. Take a pic or two before it comes all apart. Again, hopefully you got this by now.

I got a couple of pics. Driver's side.