Jump to content

8 Ball Shift Knob

Philmo

Recommended Posts

Philmo Enthusiast

Philmo

Posted
Posted

here's something else i've done that i haven't seen done lately. i bought an extra shifter handle and had a friend of mine who's got a cue and table business add a regulation size 8 ball to it.

 

phil

 

8ball2.jpg

Black02Silverado Senior Enthusiast

Black02Silverado

Posted
Posted

I did the same thing to my Old 93 Sonoma, now since I sold it I put it in my 65 Impala. You probably made out better than me. Cost me $11 to buy the eight ball. Simple to install to, just drill out the 8 a tad smaller than the shaft size and sefl thread on. :rolleyes: It has a nice feel to it too. :nono:

Philmo Enthusiast

Philmo

Posted
  • Author
Posted
I did the same thing to my Old 93 Sonoma, now since I sold it I put it in my 65 Impala.  You probably made out better than me. Cost me $11 to buy the eight ball. Simple to install to, just drill out the 8 a tad smaller than the shaft size and sefl thread on. :rolleyes:  It has a nice feel to it too. :nono:

that install won't work. i tried to do that actually. the original shift knob doesn't unscrew. it is molded on. i pretty much had to rip, cut and do a lot of yanking to get it to come off in pieces. when i tried to put the original 8 ball that i had on it, i managed to break it in half. i figured that maybe i should get a pro to do it right.

 

phil

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      Slate Electric Truck

      By asilverblazer · Posted

      I like the idea.  I would pick diesel if I had a choice. I need pictures though.
    • newdude
      Help purchasing a touch screen digitizer

      By newdude · Posted

      I've installed cheap eBay new aftermarket digitizers before.  They work.  Did a bunch of Cadillac CUE (aka Cadillac's MyLink) for someone years ago.  They all worked fine after the repair.    That number 22740886, that is a component part # for GM.  You can use it to search, but its not something that's obtainable at the dealer level.     So pretty much any of these will work - 2015 Colorado Digitizer for sale | eBay
    • asilverblazer
      give me some tips to make my truck look better

      By asilverblazer · Posted

      Black bumper and the later years Z-71 style color matched grille.
    • fondupot
      Exhaust heat while towing!

      By fondupot · Posted

      You can install tailpipes that direct the exhaust sideways vs the OEM one that goes straight back. There are several on the market, do you own research. HOWEVER, you need to make sure the Venturi vents are still intact, otherwise it will throw a engine code. There is a sensor somewhere that detects back pressure on the exhaust. And if it doesn't collect the correct metrics, it will throw the truck into limp mode. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...