Jump to content

Recommended Posts

Posted

I have a 2014 silverado 1500  with a 5.3l, I have the P06DD code, does anybody have any actual solutions for this problem? I have been searching and no one has seemed to actually found a definite reason for this code or solution. Any help would be greatly appreciated.

Posted
15 hours ago, BArriaga8 said:

I have a 2014 silverado 1500  with a 5.3l, I have the P06DD code, does anybody have any actual solutions for this problem? I have been searching and no one has seemed to actually found a definite reason for this code or solution. Any help would be greatly appreciated.

Mine had the same problem. It’s the engine oil pressure switch gauge. It’s like 50$ part from online, which you want to make sure the kit includes the sensor AND the filter screen for it, otherwise you’ll get the same code in no time. The worst part is the labor for it. It’s from build up of carbon in the engine that “gunks” up the oil and gets trapped on the filter sending a code for “stuck in off position”. I looked around and older GM’s you could have done the labor yourself though kinda tough. The 14 like I have, it just so happens to be inside the engine, right below the headers somewhere, which only makes the labor that much more expensive. Overall I’d look around at pricing on replacing the sensor and filter. Bulk of price is almost completely labor related. Mine would come on and off, once I did some work on the truck luckily it just so happened to free up and now is never on. Most people with this problem will see their check engine light come on and off(on more often than off). Hope this could get some insight. 

Posted

I found 14 TSB's related to that code...Are you having any other conditions or codes at the same time? A little more information might help the folks on the forum here to think about what your problem is...

  • 10 months later...
Posted

I have the 14 and am right at 133,000 miles and just recently got this code, it is off now.  2 fill ups ago I used a fuel additive (STP type stuff) which I have never done prior to this.  From reading these comments, I am thinking that possibly the additive cleaned up some of the carbon build up and has caused the "gunk" to get trapped on the filter and may have triggered the code.  Is this possible or more of an unrelated coincidence???   

  • 10 months later...
Posted

I have a 2014 with the code P06DD.  Had the vehicle serviced twice to clean it up and replace oil sensor. The P06DD is still showing. After some searching I discovered SB-10080702-2280  https://static.nhtsa.gov/odi/tsbs/2016/SB-10080702-2280.pdf

Subject: Models: Service Bullet,in PRELIMINARY INFORMATI01 N Code P06DD No Or Low Oil Pressure

2016 Cadillac CTS-V

2015-2016 Cadillac Escalade

2016 Chevrolet Camaro

2014-2016 Chevrolet Corvette

2014-2016 Chevrolet Silverado

2015-2016 Chevrolet Suburban, Tahoe

2014-2016 GMC Sierra

2015-2016 GMC Yukon XL

Built with RPO's 4.3L 5.3L 6.2L L83 L86 L T1 LT4 LV3

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this Pl.

Condition/Concern Bulletin No.: PIP5407

Date: Jun-2016 Vehicle setting code P06DD, no or low oil pressure, oil control valve may be stuck off commanding high oil pressures (95 psi) and or oil pump face may be damaged.

Recommendation/Instructions Tensioner spring in timing chain guide may be "short" not fully seating into guide pivot end. Cycling Oil Pump Control Valve will not cause changes in oil pump response.

1) Short spring not reaching the pivot. Replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oilTensioner spring in timing chain guide may be "short" not fully seating into guide pivot end.  

This is a major issue with a very large repair bill of $1500 to $2000 USD.

  • Sad 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,915
    Total Members
    8,960
    Most Online
    ChristopherDobson
    Newest Member
    ChristopherDobson
    Joined
  • Who's Online   0 Members, 0 Anonymous, 1,208 Guests (See full list)

    • There are no registered users currently online
  • Latest Articles

  • Posts

    • Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • 10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.
    • yes, leaking exhaust will mess up o2 sensor readings, which in turn messes up fuel trims.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...