Jump to content

2020 Silverado Lt Front Axle Replacement with Trail Boss Axles

andrewb24
 Share

Recommended Posts

andrewb24 Enthusiast

andrewb24

Posted
Posted

GM looked at my truck and said I needed new cv axles and that they were replacing them under warranty until I brought it back after they received the axles that were on back order and then said they couldn't do it under warranty after looking at it closer.   They quoted me $1400 to do the repair but that included replacing my leveling kit I have on it now which is a 2.5" motofab upper strut spacer.  I tried calling and arguing saying motofab made this kit for this truck and really all that needs to be done is add some new clamps and pack some more grease on the ones I have but couldn't reach them yesterday so I went ahead and just ordered a front axle off of a trailboss since they are longer to accommodate for the lift since it was only about $175 and I will try and replace my self and if that goes smooth I will go ahead and order a 2nd one for the other side.  So if anyone has any info on removing and reinstalling cv axles it would be appreciated.   Im not sure what all I will have to disconnect just to remove the axle as far as the upper control arm, sway bar, struts, etc.??

Gangly Senior Enthusiast

Gangly

Posted
Posted

Its relatively easy and quick.

 

Remove the  wheel speed sensor from the Knuckle.

Remove the Axle Nut from the Front Axle at the Knuckle.

Remove the Rotor from the Knuckle

Remove the nut connecting the Upper Control Arm to the Knuckle.

Remove the nut connecting the Lower Control Arm to the Knuckle.

Remove the Knuckle

Remove CV Axle

 

Installation:

Reverse removal procedure.

 

newdude Senior Enthusiast

newdude

Posted
Posted
2 hours ago, andrewb24 said:

I tried calling and arguing saying motofab made this kit for this truck and really all that needs to be done is add some new clamps and pack some more grease on the ones I have but couldn't reach them

 

Its an aftermarket kit.  Its not a GM kit, therefore no warranty if something fails as a result of installing the aftermarket kit.

 

IF you did the GM 2 inch factory lift and had a problem, then yes you'd have warranty.  

andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted
1 hour ago, Gangly said:

Its relatively easy and quick.

 

Remove the  wheel speed sensor from the Knuckle.

Remove the Axle Nut from the Front Axle at the Knuckle.

Remove the Rotor from the Knuckle

Remove the nut connecting the Upper Control Arm to the Knuckle.

Remove the nut connecting the Lower Control Arm to the Knuckle.

Remove the Knuckle

Remove CV Axle

 

Installation:

Reverse removal procedure.

 

is it easy removing the axle from the differential? 

Gangly Senior Enthusiast

Gangly

Posted
Posted (edited)
2 hours ago, andrewb24 said:

is it easy removing the axle from the differential? 

Get a large flat screwdriver, or preferably a flat prybar, slip it between the axle bushing (cup) and differential then work it right off.

Edited by Gangly
andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted
4 hours ago, Gangly said:

Its relatively easy and quick.

 

Remove the  wheel speed sensor from the Knuckle.

Remove the Axle Nut from the Front Axle at the Knuckle.

Remove the Rotor from the Knuckle

Remove the nut connecting the Upper Control Arm to the Knuckle.

Remove the nut connecting the Lower Control Arm to the Knuckle.

Remove the Knuckle

Remove CV Axle

 

Installation:

Reverse removal procedure.

 

can you not work the axle out without removing the rotor or lower control arm knuckle?   I dont have to disconnect the sway bar do i?

Gangly Senior Enthusiast

Gangly

Posted
Posted

Removing the rotor gives you more room to work with, but I don't know that its absolutely necessary. 

 

The bolt connecting the Lower Control Arm to the Knuckle is required to remove the Knuckle, so yes it needs to be removed according the the service manual.

 

The sway bar is connected to the Lower Control Arm and is not required to be removed. 

 

Its a very simple and easy procedure that you might be overthinking or overly concerned about, but don't worry.  Its a 2 or 3 on a scale of 1 to 10 with 10 being the most difficult, and disconnecting the Knuckle from the Upper Control Arm and Lower Control Arm is the easiest and fastest way to accomplish the task.  

 

Once the wheel is off, removing the Knuckle to pull the CV literally consists of removing 4 nuts:

Axle Nut, UCA to Knuckle Nut, LCA to Knuckle Nut, and Tie Rod to Knuckle Nut.  It should take you 2 minutes to accomplish once you have the wheel off.

andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted
On 1/5/2021 at 5:43 PM, Gangly said:

Removing the rotor gives you more room to work with, but I don't know that its absolutely necessary. 

 

The bolt connecting the Lower Control Arm to the Knuckle is required to remove the Knuckle, so yes it needs to be removed according the the service manual.

 

The sway bar is connected to the Lower Control Arm and is not required to be removed. 

 

Its a very simple and easy procedure that you might be overthinking or overly concerned about, but don't worry.  Its a 2 or 3 on a scale of 1 to 10 with 10 being the most difficult, and disconnecting the Knuckle from the Upper Control Arm and Lower Control Arm is the easiest and fastest way to accomplish the task.  

 

Once the wheel is off, removing the Knuckle to pull the CV literally consists of removing 4 nuts:

Axle Nut, UCA to Knuckle Nut, LCA to Knuckle Nut, and Tie Rod to Knuckle Nut.  It should take you 2 minutes to accomplish once you have the wheel off.

I got the driver side completed and was pretty easy. I took my time on the first side but the next side should go pretty easy. Little harder to get axle through hub than I thought and the part I worried most about was the easiest (removal of the axle at differential) 

 

I do have a rubbing noise when driving and it’s the same noise it made after I installed my leveling kit a few months ago but it went away after tightening the upper strut nuts but this time I checked everything and all seems tightened up. Didn’t get time to go back in and look but I believe It has to be the shield or whatever it is behind the rotor or the thin plate on the outer cv axle that’s right behind the hub.  It’s a metal grinding or rubbing type noise.

andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted

I fixed the rubbing noise on the driver side last night.  It was just a bent dust shield behind the rotor from when I set the hub assembly on the ground. Thank goodness that was an easy fix.  I didn't feel good yesterday so I didn't start the passenger side yet but it should go twice as fast being I know exactly how to do it now and I took it real slow and easy on the first side.   I did overthink this mainly from watching a guy on youtube who kept stressing about how bad it would be to bust a boot or clamp while he was installing a lift kit on a 2019 silverado but this was easier than installing the leveling kit itself.

 

Also I thought about just re-greasing and fixing the boots on the driver side axle I took off and move it to the passenger side then take the other one back which would leave me with 1 spare axle or just go all new and have 2 spares which I will try and restore anyway or I could sell them.

Gangly Senior Enthusiast

Gangly

Posted
Posted

It really is a simple task that I think most people over think and worry endlessly about, definitely not worth spending $1400 on.  I'm glad you got it worked out and don't worry about the bent dust shield, your not the first to do it :).  I did the same thing when I replaced a front diff in another vehicle last year and as soon as I rolled down the road I started hearing a rubbing noise and freaked out.  Turned out I bent the dust shield up against the rotor as well.  I pulled it back and everything worked perfectly. 

 

Also, what you have done is significantly more than what is done to raise a vehicle using aftermarket shocks and springs.  If you had a lift kit you could have installed it in the process of putting everything back together and gotten rid of that 2.5" spacer :).

 

I  would keep the old two CV's as spares, you never know when you might be off-roading, or even on-roading, and snap one by accident.

 

Again, I'm glad you got it done and now hopefully you have the confidence to attack some bigger truck projects if you ever want to.  

 

 

andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted
2 hours ago, Gangly said:

It really is a simple task that I think most people over think and worry endlessly about, definitely not worth spending $1400 on.  I'm glad you got it worked out and don't worry about the bent dust shield, your not the first to do it :).  I did the same thing when I replaced a front diff in another vehicle last year and as soon as I rolled down the road I started hearing a rubbing noise and freaked out.  Turned out I bent the dust shield up against the rotor as well.  I pulled it back and everything worked perfectly. 

 

Also, what you have done is significantly more than what is done to raise a vehicle using aftermarket shocks and springs.  If you had a lift kit you could have installed it in the process of putting everything back together and gotten rid of that 2.5" spacer :).

 

I  would keep the old two CV's as spares, you never know when you might be off-roading, or even on-roading, and snap one by accident.

 

Again, I'm glad you got it done and now hopefully you have the confidence to attack some bigger truck projects if you ever want to.  

 

 

i really thought about getting new control arms and having them ready to install at the same time but I had been wanting to get this done for awhile so I was patient enough to find some and then wait for them.

andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted

I finished the other CV Axle last night.  Feels good to have this project complete and while I was in there I cleaned up all the grease from the boots on the other axles.   When I rolled under to put the skid plate back on I looked at the angles of the axles and to me they do not look that bad so I am wondering when the dealer had it if they just looked at the angle while the truck was on the lift because the whole front suspension is drooping so the angle looks really bad on the axles but on the ground I think they are fine.

  • Like 1
  • 1 month later...
viperdad Enthusiast

viperdad

Posted
Posted
On 1/13/2021 at 6:42 AM, andrewb24 said:

I fixed the rubbing noise on the driver side last night.  It was just a bent dust shield behind the rotor from when I set the hub assembly on the ground. Thank goodness that was an easy fix.  I didn't feel good yesterday so I didn't start the passenger side yet but it should go twice as fast being I know exactly how to do it now and I took it real slow and easy on the first side.   I did overthink this mainly from watching a guy on youtube who kept stressing about how bad it would be to bust a boot or clamp while he was installing a lift kit on a 2019 silverado but this was easier than installing the leveling kit itself.

 

Also I thought about just re-greasing and fixing the boots on the driver side axle I took off and move it to the passenger side then take the other one back which would leave me with 1 spare axle or just go all new and have 2 spares which I will try and restore anyway or I could sell them.

I messed up the bottom boot when replacing the coilover on my 19 trail boss so not sure if its possible to just replace the boot or just order the whole axle. The dealership obviously wants to change the whole axle. Do you by chance have a part number of the axle? I want to make sure its the one I’m looking at and Even though the diagram on gm parts website shows everything separate, I assume its assembled and sealed and ready to instal right? Also do you think its possible to just change the bottom boot? When you disconnect the hub is there a way to take the joint off so the slim side of the boot can slip in?

063608E5-A213-4986-A0A6-1DD179B29EFC.png

andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted
39 minutes ago, viperdad said:

I messed up the bottom boot when replacing the coilover on my 19 trail boss so not sure if its possible to just replace the boot or just order the whole axle. The dealership obviously wants to change the whole axle. Do you by chance have a part number of the axle? I want to make sure its the one I’m looking at and Even though the diagram on gm parts website shows everything separate, I assume its assembled and sealed and ready to instal right? Also do you think its possible to just change the bottom boot? When you disconnect the hub is there a way to take the joint off so the slim side of the boot can slip in?

063608E5-A213-4986-A0A6-1DD179B29EFC.png

 

B620B3AA-3A0B-43F8-847E-B40FB765178E.jpeg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,760
    Total Members
    8,960
    Most Online
    MASONV88888888
    Newest Member
    MASONV88888888
    Joined

  • Who's Online   1 Member, 0 Anonymous, 1,506 Guests (See full list)

  • Latest Articles

  • Posts

    • MASONV88888888
      Another 6.2L engine failure!

      By MASONV88888888 · Posted

      My 2025 Silverado 1500 had to receive a brand-new engine (long block) under warranty last month at only around 16,500 miles. Before the replacement, the truck repeatedly displayed "Engine Oil Level Low" warnings, even though the Oil Life Monitor still showed around 50% remaining after about 6,000 miles since my last oil change. After seeing the warning several times, I checked the dipstick with the engine cold, and the oil level was completely normal. The next day, the message escalated to "Add Engine Oil." At first, I assumed it was just a faulty oil level sensor, so I brought the truck to the dealership. After inspecting the engine, they found internal cylinder wall scoring and ultimately replaced the entire long block under warranty. Before this happened, I was planning to install a 4-inch lift and suspension upgrade on my truck. After needing a new engine at just 16,500 miles, I honestly don't see the point anymore. I also contacted GM to ask whether my vehicle qualified for a buyback, but I was informed that it does not at this time. Anyway, this experience has left me with serious concerns about the long-term reliability of this engine. I sincerely hope NHTSA expands the current investigation or recall to include 2025 model and performs a thorough inspection of affected vehicles. My biggest concern is that these engines may fail shortly after the powertrain warranty expires. If GM truly stands behind this engine, then at the very least, please consider extending the powertrain warranty to 10 years for affected owners. That would go a long way toward restoring customer confidence.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      Without exception but then I'm the odd duck, right? I know what goes into that test, how it is calculated and thus how to beat it. But EPA values are often not beaten by the general public and the government has in past years adjusted the means and methods to come to those values to more closely approximate "Joe Average".    The only real trick to beating that EPA average is don't drive like "Joe Average".    It's the same method you used to profit from "Economic Migration" and in doing so beat the 'stats'. But you, like me, are not "Joe Average".     The thing you don't seem to grasp is this "Purchasing Power Index" isn't forward looking. It doesn't predict what it going to be but looks backward and states what it was. They are not telling us what the THINK, they are telling us what they MEASURED. Example:    Wife says "I'm going to lose 40 pounds by Christmas". May she does, maybe she doesn't but the doctors office who weighed her when she made that statement and again at Christmas only REPORTS what the RESULT was. You and I can banter about what was possible and what aunt Tilly did till the cows come home but the result is the result. Arguing otherwise is.....irrational. That's all I'm saying. This isn't about:      What you are calling a 'Statistic' is a RESULT not a CALCUATION and as a result the RULE. Like gravity as a rule, it can not be broken. 
    • MASONV88888888
      Rattle in the rear!

      By MASONV88888888 · Posted

      Just wanted to say thank you for posting this. Years later, your thread is still helping Silverado owners.   I bought my 2025 Silverado 1500 in January 2025, and I've had what feels like the exact same rattle since day one. After reading your findings, I believe my truck has the same issue with the cable carrier contacting the rear sliding window. To be honest, I had pretty much given up on pursuing the issue. It wasn't until I recently drove another brand's pickup that I realized just how quiet their cabin was—and how noisy mine has been all along. On my truck, the rattle happens on almost any paved road, gets even worse on rougher pavement, and I can even hear it during braking and acceleration.   I actually referenced your thread when submitting my case to GM, hoping they'll recognize this as a recurring issue instead of treating it as an isolated incident. The reason I reached out to GM first is because my dealership told me they would need to keep the truck for at least two days just to diagnose the problem. I was concerned that even after two days, they still might not be able to identify the source of the rattle before giving the truck back to me. I had also asked a few dealerships about this issue during previous service visits, but none of them seemed to know what was causing it or had a solution. That's why I decided to contact GM directly first, hoping they might already have an official repair procedure or guidance for this issue.   I also hope GM eventually comes up with an official fix for this problem. I have a feeling there are many Silverado owners experiencing the same rattle, but most either choose to live with it or simply don't know what the cause is.   Really appreciate you taking the time to document your diagnosis. Your post is still making a difference years later.
    • Buckwild27
      Gas Prices

      By Buckwild27 · Posted

      I have 2 choices. 
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      Do you have access to BP fuels? Some stations have Silver 91 E-0 priced the same as their 93 E-10.  There is a local Marathon with 90 alky free for $6 a gallon but I go down the road to BP for $5-ish. They also have a 100 E-0 but that stuff is $10 a pop. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...