Jump to content

clicking form behind the dash

rick merrow
 Share

Recommended Posts

rick merrow New Member

rick merrow

Posted
Posted (edited)

got a 2001 chevy silverado z71...just started clicking behind dash...no click while stopped only when moving and it speeds up and slows down as truck does, what is this? anyone?

Edited by rick merrow
Brian715 Enthusiast

Brian715

Posted
Posted

Most of my dash clicking stuff has been blend door actuators for the Heat/ac ducts but that doesn't really make sense with it changing with engine speed. Hmm.

Sharpz Enthusiast

Sharpz

Posted
Posted
On 5/12/2021 at 1:16 PM, rick merrow said:

bump

The top suggestion as to the ticking/clicking noise from behind the dash was given to you.  You didnt even acknowledge the person giving you the help.  Did you look behind your dash? Did you check into the actuator problem?  I dont know of any sensors that would cause a ticking/clicking with speed that you would hear inside the cab, sometimes you can hear clicking from a relay, but never heard of it speeding up or slowing down.  The actuator is the best answer, and until you do something to see if that is the problem I dont think anyone is going to be able to help you narrow it down. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • DaleB
      No Software Updates - Old Build

      By DaleB · Posted

      Hi all - my current truck is a 2022.5 1500 High Country 3.0. I bought the truck used last year. After doing some digging, I noticed that my truck's software is stuck on the original build from 2022. I have no available software updates. I talked to my dealer about this and they recommended not trying to force an update since the 36,000 mile warranty is expired. This is a big bummer since there have been many major releases since that have fixed small issues and improved speed/usability.   For reference, the current software build number is: full_gminfo37_gb-user 10 W158E-W164.4.2-QIH22B-563.3 158 release-keys Has anyone had a similar experience? Should I just forget about it and move on, or try a different dealer?
    • B07
      Needing this part.

      By B07 · Posted

      Sure. Buy it for me 🤣
    • B07
      Needing this part.

      By B07 · Posted

      Using zip ties but 2-3 they snap due to sharp edges. Just using a shoestring. Last longer. 🤣
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      I ordered the Snap On...waiting for it to come in later this week or early next week.   New front cover, new crank seal and new balancer are on. Water pump, pulley, fan, hoses, and plastics reinstalled. I can move forward knowing all my timing marks are dead on and the front engine is hopefully sealed better than it was. Take 2 with the water pump...trying high temp thread sealer on the lower bolts.   Rebuilt injector and new-new regulator is in, it looks like new. Top intake reassembled and all the bits are reconnected and snugged down.   Thinking about knock sensors again, I located both of mine and, there's your problem, Francis... The driver's side one is broke, plastic is bashed in, part of the wire is bare, and it appears to have been damaged like that for a long time. I saw the wire but didn't think anything of it. The knock sensor might not be my pulled timing issue, but it sure looks suspect. It must still be conducting, otherwise I'd expect a CEL. But perhaps with its sacred crystal inside exposed, jilted and dirty, maybe it's sending mixed signals. So I'm waiting for one of those and a new pigtail to come in. Pass side sensor looks good, except for the spark plug wire resting on it (!). The plug wires are healthy so it shouldn't be causing an issue, but I separated them and added zip ties to nearby looms to keep everything well apart.   So, I'm down to installing a knock sensor AND, oh, replacing the exhaust and cat. I actually think that's going to be fairly easy, it's all bolt-together, all new stuff from Walker is laid out on the shop floor ready to go. Hopefully have this thing on the road again for the weekend.   My luck? It will still be leaking oil, coolant, pulled timing, intermittent CEL for running rich, or it probably won't run at all -- because that's how this project has gone.   I've never worked on a vehicle so ...hurt? ...cursed? in my life. Everything has been effed with SO HARD, but I think...knock on wood...I've managed to undo all the backyard stuff and we're almost reset back to "just" an 80k mile, 30 year old Blazer.
    • PunchT37
      Would this CV Shaft be bad?

      By PunchT37 · Posted

      Yes. You need to check out that thing, and the hub further.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...