Jump to content

1500 with 2500 bumper?

Jeremiah Levy
 Share

Recommended Posts

Jeremiah Levy Enthusiast

Jeremiah Levy

Posted
Posted

I am working on blacking out my truck and found a bumper that was removed with less than 500 miles for a lift gate that is all black but comes off a 2500. It looks like aftermarket all fit both for the 2019-2021 models but will the stock be a seamless swap? I found in other sites they would bolt up fine but fit the same was the 1500 does but they were answering the question about older models. 

 

Thank you 

 

Transient Senior Enthusiast

Transient

Posted
Posted
On 7/9/2021 at 9:36 AM, Jeremiah Levy said:

I am working on blacking out my truck and found a bumper that was removed with less than 500 miles for a lift gate that is all black but comes off a 2500. It looks like aftermarket all fit both for the 2019-2021 models but will the stock be a seamless swap? I found in other sites they would bolt up fine but fit the same was the 1500 does but they were answering the question about older models. 

 

Thank you 

 

Have you tried going to a website like gmpartsdirect and compared part numbers between the 2 trucks?

Jeremiah Levy Enthusiast

Jeremiah Levy

Posted
  • Author
Posted
5 hours ago, Transient said:

Have you tried going to a website like gmpartsdirect and compared part numbers between the 2 trucks?

That's what has me confused. I thought the body of a 2019-2021 was the same but the 2021 Silverado 1500 lt isn't listed while a 2020 is. 

Screenshot_20210713-093848.png

Screenshot_20210713-094044.png

Transient Senior Enthusiast

Transient

Posted
Posted
17 hours ago, Jeremiah Levy said:

That's what has me confused. I thought the body of a 2019-2021 was the same but the 2021 Silverado 1500 lt isn't listed while a 2020 is. 

Screenshot_20210713-093848.png

Screenshot_20210713-094044.png

GM didn't change anything.  It'll fit.  The 2020s being listed has me confident. 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      In the 80's 90's I'd run Honda's 7,500 miles between changes using Red Line HP 5W20 and do it for hundreds of thousands of miles with issues. Back in the day it was an SAE 20 with the HTHS of a SAE 30 and SN add load. It was also very polar. Oxidation VOA was over 120. Besides those motors were SPFI and lean burn tech. I could have likely run it longer but never did.    We had a Toyota bought new I ran on Pennzoil's latest and greatest synthetic of the day with "Penthane". A made up word for a very low dose of PAO. Tried 7,500 mile OCI's in that Group III/VI chemistry and the rings tapped out at 90K. Rocker box wasn't as bad as the one Punch put up but it wasn't good either. Also a SPFI motor.    I'm around 3,750 across the board on these GDI monsters and the oil it tapped out by then usually on TBN/TAN crossover and color. Red Line HP Euro.    The AMSOIL SS brochures tell you to follow the OEM values for the service class but that it can be run up to 25K if monitored. I can't imagine what motor could go that distance and not tap out. I've never owned one.    Yes, I know. Lot's of people do. I'm just not going to be one of them. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I knew a guy in the early 80's that bought a new Monte Carlo and ran it a 100,000 miles without ever changing the filter or the oil. Just kept adding. It looked like that inside.     
    • whenindoubtuseahammer
      My First Project and GMC has me stumped

      By whenindoubtuseahammer · Posted

      Good evening. I was lucky enough to get passed down to me a 2007 GMC LBZ that was my great uncle's. While the underside and rockers are more or less gone I feel like with time I can restore it to working order since it only has 110,000 miles and he put nearly every option he could get without getting the new body style since he did not trust DEF. So far I have done everything I can think of but when I put the key into the ignition nothing happens. I put 2 brand new batteries in it. Cleaned the terminals. Check all the fuses and relays and they all pass with my multimeter. I know I'm missing something that I just cant think of. The only odd thing is the OBD2 port works which makes me think its not the mega fuse. Any advice would be greatly appreciated. 
    • PunchT37
      Casey from the Texas Hill Country

      By PunchT37 · Posted

      Looks nice. I still have my 2000, 1500. Bought a 2025, 1500 for retirement. Feels solid. These trucks have a bad rap on the internet. My brother has a `24 1500, 5.3 with 52,000 miles. No problems at all. Mine hasn`t either but mine`s only at 12,700 miles. Have seen some of these things with 100,000 miles with no problems.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...