Jump to content

Looking for help on airbag compressor installation

tweeder01
 Share

Recommended Posts

tweeder01 Enthusiast

tweeder01

Posted
Posted

This is the system I'm putting in.  The buttons on the controller don't work anymore and can't get a replacement.  So I'm going to cut the controller off and add a digital bag pressure guage and a switch to air up and down the bags.  I can't figure out how to add the switch.  The switch I guess is a 3 position momentary switch that defaults in the middle and you have to hold it to either side.  I assumed that one way will inflate  and the other will deflate as it came with the guage package.    I got the guage to work.

 

 

Screenshot_20220711-162614_Word.jpg

cwtech Enthusiast

cwtech

Posted
Posted

i am not familiar with your system.

 

Will the compressor run only when you want to increase the bag pressure?

 

Where/how is the air exhausted to lower bag pressure?

 

Does the solenoid allow the pressure into the bag, or is it there to exhaust air?

 

Is there a check valve on the compressor discharge to prevent air leakage back through the compressor?

tweeder01 Enthusiast

tweeder01

Posted
  • Author
Posted (edited)
32 minutes ago, cwtech said:

i am not familiar with your system.

 

Will the compressor run only when you want to increase the bag pressure?

 

Where/how is the air exhausted to lower bag pressure?

 

Does the solenoid allow the pressure into the bag, or is it there to exhaust air?

 

Is there a check valve on the compressor discharge to prevent air leakage back through the compressor?

Yes the compressor only runs when you increase the bag pressure.  The air is exhausted from the air solenoid.   It is to exhaust the air pressure.  The check valve for air is that block.  The air from the compressor comes from the bottom and into the left and right ports atbthe top to the airbags.  The others a pressure sensor that tells it when to shut off at the set pressure.  But that all doesn't work anymore.  I need to be able to control it via the switch, thaya whatbi need help wiring it up.

Edited by tweeder01
cwtech Enthusiast

cwtech

Posted
Posted (edited)

There may be other ways of doing this, but this is what I would do.

 

A DPDT switch is available in toggle-switch style or rocker-switch style.    ...There will be six terminals and they may be screw terminals or push-on or solder type.

 

The reason for using a Double Pole Double Throw switch instead of a Single Pole Double Throw Switch (SPDT) is by wiring it as shown, you increase the life of the switch and add durability.

 

The switch needs to be DPDT  MOMENTARY (it returns to the center position when you release it) CENTER-OFF (no continuity to either pole).   ....There are lots of sources online.  ....Look for at least a 15 or 20 amp rating.  .....Price will be anywhere from $5 - $20 depending on what you choose.

 

Moving the switch one direction will activate the compressor.  ...Moving the switch the opposite direction will activate the solenoid valve.

 

41z4AcqkEpL.jpg41n8lSyCShL._AC_.jpg

Air Bag Wiring - jpg.jpg

Edited by cwtech
added info
tweeder01 Enthusiast

tweeder01

Posted
  • Author
Posted

yes that looks to be it.  But the guage came with a i guess a single pole double throw switch that i would need to use as its integrated in the guage mount.

  • Thanks 1
  • 4 weeks later...
tweeder01 Enthusiast

tweeder01

Posted
  • Author
Posted (edited)

i left everything plugged in as it was in the previous truck that was working for reference.  the solenoid has two wires, which is which?  I know the diagram shows one to ground and the other to the switch, right now the volt meter shows both have 12 volt power.

 

EDIT:  both wires show power when they're plugged in making a loop.  only one has power when both wires disconnected.

Edited by tweeder01
cwtech Enthusiast

cwtech

Posted
Posted
On 8/13/2022 at 8:04 PM, tweeder01 said:

i left everything plugged in as it was in the previous truck that was working for reference.  That is your problem!  ....I don't believe you can use your present gauge or switch, as they are part of the control panel.

....The white wire from the solenoid needs to be separated from the old wiring and connected to ground.

 

tweeder01 Enthusiast

tweeder01

Posted
  • Author
Posted (edited)
8 minutes ago, cwtech said:

i'm using the wiring harness for ease of use as its all there with connectors.  i cut off the controll unit and was using those wires to add in the new guage and switch.  ok so ill figure out a way to ground that white wire.  Any reason it wasn't grounded from the get go?

 

Edited by tweeder01
cwtech Enthusiast

cwtech

Posted
Posted
16 hours ago, tweeder01 said:

Any reason it wasn't grounded from the get go?

 

It was grounded through the old connections somewhere - possibly in the controller.

 

Your original wiring schematic was not detailed enough to know.

 

 

  • 1 month later...
tweeder01 Enthusiast

tweeder01

Posted
  • Author
Posted

Well I made the air compressor turn on with the momentary switch but couldn't figure out how to air it back down by pressing the switch the other way.  Come to find out that the digital air guage I bought is off.  I tried wiring it to the existing pressure switch there but it wouldn't read it.  So I installed the one that came with it but it was quite off.  At 10 psi the guage read 0.  At 30 it was 21.  

Traction Enthusiast

Traction

Posted
Posted

Can I piggyback on your thread with a question?

 

I have an ARB dual compressor that I would like to use for my airbag setup. Would it be easier/more cost effective to just buy the purpose built system rather than try to adapt my current compressor? Wiring is my thing, solenoids and all that is not.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined

  • Who's Online   4 Members, 0 Anonymous, 1,245 Guests (See full list)

  • Latest Articles

  • Posts

    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • TrueBlue
      No Software Updates - Old Build

      By TrueBlue · Posted

      That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed. Why not updates as well, especially since some of those can be safety related also?
    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      That's good to know, but I don't think I'll even be running them under 45 in the rear  unless it's on the sand or something but will only be for a short distance anyways!    I didn't read all the instructions in the booklet yet, but do you know let's say I set the rear psi on the placard to 45, will the warning light come on soon as it drops under 45 or is there a percentage it has to drop from the set value before the warning light is triggered?
    • newdude
      Would this CV Shaft be bad?

      By newdude · Posted

      That's bad.  Like, its probably destroying the stub axle the CV slides into.   Do you have a proper lift installed with differential lowering brackets?  Did you install AT4/Trail Boss factory CV axles?  
    • PunchT37
      Would this CV Shaft be bad?

      By PunchT37 · Posted

      Hot? New Jersey? Today? I was working on my old 2000 Silverado 1500 today. Believe me, it was boiling hot today. As it has been.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...