Jump to content

Over Heating

Larry Rinehart
 Share

Recommended Posts

Larry Rinehart Enthusiast

Larry Rinehart

Posted
Posted

My 2003 Sierra HD crew cab pickup overheats when I pull my toy hauler, especially in hilly terrain. I bought the truck new, have take care of it, and it only has 80,000 miles on the odometer. I pull a small toy hauler with motorcycle in the back. It overheats on hills and when going slow in traffic. And, the AC only works well when I’m traveling at highway speeds. The engine is solid, always changed oil at 3k and it never uses a drop of oil. My question is: can I do anything to fix the overheating problem, bigger radiator, etc? I’ve had the current radiator flushed and refilled accordin

hiking_mike Enthusiast

hiking_mike

Posted
Posted

I have a pair 07 2500's. I started noticing the transmissions would get close to the max of what I felt confortable with.

We opened up the 'stack" or I mean We removed the radiator. What I first noticed is that the holes in the various devices as air passes through get smaller and smaller. The radiator is last, and has smallest, AC condnsor is largest.

So bugs and debris wil pass through condensor, intercooler, then in to the radiator, where they get stuck and block air flow.

Removing the radiator on both trucks, i noticed a lot of dead bugs, road grime, and debris.  So using a lot  degreasor and water hose, it took some effort to clean the raditor. I also u sed a power washer on low pressure making sure not to do a "sweeping action" in order to keep from messing up the fins.

Then spraying what was left in the truck, the intercooler and condensor from back to frount, this cleand the intercooler and condensor, and transmission cooler.

This made a HUGE difference in transmission and engine temps. I took a 7,000 camper all the way to Key West in July -August time frame.

I went from having to slow down to about 60 and lots of stops to allow wverything to cool off to having no issues at all.

  • Like 1
hiking_mike Enthusiast

hiking_mike

Posted
Posted

Make sure your transmission is in Tow Mode, I noticed in heavy traffic, and one time I forgot to activate and was suprssed how hot the transmission got so quickly. I have had to repalce the little push button that goes on the shift lever, as the wire shorted out.

Removing the radiator was not too difficult. kind of a tight fit getting out. 

newdude Senior Enthusiast

newdude

Posted
Posted (edited)
1 hour ago, Larry Rinehart said:

My 2003 Sierra HD crew cab pickup overheats when I pull my toy hauler, especially in hilly terrain. I bought the truck new, have take care of it, and it only has 80,000 miles on the odometer. I pull a small toy hauler with motorcycle in the back. It overheats on hills and when going slow in traffic. And, the AC only works well when I’m traveling at highway speeds. The engine is solid, always changed oil at 3k and it never uses a drop of oil. My question is: can I do anything to fix the overheating problem, bigger radiator, etc? I’ve had the current radiator flushed and refilled accordin

 

 

Fan clutch bad?  I seem to recall a string of these in the 01-07 range that had overheat issues due to bad fan clutches.  If it can't engage and ramp up the fan speed, its not going to pull in extra air across the radiator in lower speed driving.  

Edited by newdude
  • Like 1
Larry Rinehart Enthusiast

Larry Rinehart

Posted
  • Author
Posted

Thanks for the helpful replies. I cleaned the bugs from the radiator today, only to find there are four radiators of varying size. The biggest and closest to the fan is the engine coolant, directly in front of it, and slightly smaller, is what I assume to be the transmission radiator. In front if that and much smaller is a radiator of unknown purpose. Off to the side and even smaller is the power steering radiator. Interesting. I will take the truck to the shop to have the fan clutch checked. And yes, I always tow in tow mode. Again, thank you all for the help. Larry Rinehart

vucelick Enthusiast

vucelick

Posted
Posted (edited)

In addition to above posts check thermostat, and make sure the water pump is functioning properly.  Have you always run dexcool antifreeze?  I remember initially dexcool was not comptible with other coolants, leading to corrosion and seal issues.

Edited by vucelick
newdude Senior Enthusiast

newdude

Posted
Posted
33 minutes ago, Larry Rinehart said:

Thanks for the helpful replies. I cleaned the bugs from the radiator today, only to find there are four radiators of varying size. The biggest and closest to the fan is the engine coolant, directly in front of it, and slightly smaller, is what I assume to be the transmission radiator. In front if that and much smaller is a radiator of unknown purpose. Off to the side and even smaller is the power steering radiator. Interesting. I will take the truck to the shop to have the fan clutch checked. And yes, I always tow in tow mode. Again, thank you all for the help. Larry Rinehart

 

 

Looking at the grille of the truck, the vertical mounted one on the driver's side is power steering, the rectangle in the middle on that "A" brace is transmission, behind that is the AC condenser and then last is the radiator.  

hiking_mike Enthusiast

hiking_mike

Posted
Posted

If you watch your transmission temp guage, I believe about 185 you should begin to hear the fan clutch engage until the temp drops. Forgive me, since I removed the radiator and cleaned, I dont have the issues I used to and forgot the temps it used to kick in.

You may hear the fan clutch on a cool damp morning for a few minutes or so. 

As for the cooling "stack" its nickname is called stack sometimes due to all the cooling devices mounted in succession. 

It the "radiator looking thing" is your intercooler. This cools the turbo charged airflow before it goes into intake of the engine. .

The only way to really clan the radiator is to remove it. You are not going to really blow water from back towards the  front very well at all.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Parking Brake - Automatic Engagement Questions

      By Another JR · Posted

      On 2021 3500hd it consistently sets automatically when selecting park if the incline/decline is above a certain angle. 
    • Policeoff01
      Feeling Vibration and Jiggles in 2024 HD Gasser Steering Wheel

      By Policeoff01 · Posted

      Curious, did anyone ever get a fix for the vibration reported here.   I have a 2024 Silverado with 6.6 duramax.   I’m noting the same vibration resonating up through the steering shaft into the steering wheel.    Best way to describe- like someone is tapping on the steering shaft/components and it’s resonating into the steering wheel.    thanks. 
    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...