Jump to content

A/C failure cause???

Somethingclever_2014GM
 Share

Recommended Posts

Somethingclever_2014GM New Member

Somethingclever_2014GM

Posted
Posted

Profile: 2014 Chevy Silverado. 5.3L Z71 crew cab short box. 

Can't isolate the problem with my truck A/C. 

 

Blows air temperature air out of it. A/C compressor clutch turns when turned on. Turns off when turned off. A/C module used to get stuck if you accidently turned it to warm air and back to cool. Knob would turn all the way, but the temp would not get as cool as it did. Now it does not get cool at all. 

A/C freon levels have recharged, purged, and recharged again. Ensured proper levels of refrigerant went into A/C system. No difference. 

I have checked all the fuses and relays. No problem there. 

Can't figure out if it is a blend door actuator, A/C inlet valve actuator, A/C control module, A/C sensor, or A/C compressor. Limited tools and income, so the level of testing is pretty basic. Welcome ideas and solutions. Thank you.

asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted
20 hours ago, Somethingclever_2014GM said:

...A/C module used to get stuck if you accidently turned it to warm air and back to cool. Knob would turn all the way, but the temp would not get as cool as it did. Now it does not get cool at all...

Can't figure out if it is a blend door actuator...

Not sure what part you are referring to as "getting stuck" but if the blend door was getting stuck and finally gave up, that's where I would start. 

 

If it is a dual zone system, does either side get cold?

  • Like 1
  • 2 weeks later...
Rad_Rado17 Enthusiast

Rad_Rado17

Posted
Posted
On 5/31/2026 at 2:35 PM, Somethingclever_2014GM said:

Profile: 2014 Chevy Silverado. 5.3L Z71 crew cab short box. 

Can't isolate the problem with my truck A/C. 

 

Blows air temperature air out of it. A/C compressor clutch turns when turned on. Turns off when turned off. A/C module used to get stuck if you accidently turned it to warm air and back to cool. Knob would turn all the way, but the temp would not get as cool as it did. Now it does not get cool at all. 

A/C freon levels have recharged, purged, and recharged again. Ensured proper levels of refrigerant went into A/C system. No difference. 

I have checked all the fuses and relays. No problem there. 

Can't figure out if it is a blend door actuator, A/C inlet valve actuator, A/C control module, A/C sensor, or A/C compressor. Limited tools and income, so the level of testing is pretty basic. Welcome ideas and solutions. Thank you.

Check the a/c condenser.............they are notorious for cracking at the pinch weld.  Look through the grill on the driverside.  There's a small tack weld.  If I remember right if you hold up a black light the refrigerant will glow if the weld is cracked  

 

AC Condenser replacement : r/Silverado

  • Like 3
newdude Senior Enthusiast

newdude

Posted
Posted (edited)

Hopefully your system has leak dye in it still?  A black light will help find the dye at the leaks.  

 

Yea condenser leak is probably the most common issue on the 2014-2018 generation 1500s.  

 

Next common would be the one hose off the compressor or the compressor itself.  2014s used to crack that hose near where it attached to the compressor if I'm not mistaken.    

 

EDIT:  Here's the PI for that line cracking - temp.xml  It can spray dye all over the hose and compressor if it happens.  

Edited by newdude
  • Like 3
Somethingclever_2014GM New Member

Somethingclever_2014GM

Posted
  • Author
Posted (edited)

No leaks. Replaced the condenser 3 years ago. Problem was found to be caused by the A/C blend door actuator. Just replaced it and it's blowing out the cold air it used to when I bought it. 

17812972329361589756390416668241.jpg

Edited by Somethingclever_2014GM
Included photo of replaced part.
  • Like 3
Rad_Rado17 Enthusiast

Rad_Rado17

Posted
Posted
11 hours ago, Somethingclever_2014GM said:

No leaks. Replaced the condenser 3 years ago. Problem was found to be caused by the A/C blend door actuator. Just replaced it and it's blowing out the cold air it used to when I bought it. 

I just delt with this this morning.  Already replaced my condenser two years ago.  I didn't have to replace my blend door actuator, I just had to do the relearn process and it worked. 

  • Like 1
Somethingclever_2014GM New Member

Somethingclever_2014GM

Posted
  • Author
Posted

Glad it worked for you. I tried that 1st, about 2 years ago. Didn't help. I also tried doing a hard reset (disconnecting battery for minimum of 30 minutes). Worked a couple times, but after one summer of doing it over and over, that no longer worked. 

I was fairly confident it was either the compressor or a failed actuator, but I just couldn't identify which one. Had to research which actuators do what and which last numbers are associated with each.

  • Like 1
Rad_Rado17 Enthusiast

Rad_Rado17

Posted
Posted
On 6/12/2026 at 1:53 PM, Somethingclever_2014GM said:

Glad it worked for you. I tried that 1st, about 2 years ago. Didn't help. I also tried doing a hard reset (disconnecting battery for minimum of 30 minutes). Worked a couple times, but after one summer of doing it over and over, that no longer worked. 

I was fairly confident it was either the compressor or a failed actuator, but I just couldn't identify which one. Had to research which actuators do what and which last numbers are associated with each.

Spoke to soon.  The next day my A/C wasn't getting very cold again.  I checked the system, compressor was good, both fans spinning strong.  I recharged the system myself using the UV refrigerant, the next day I used a black light and the Schrader valve has failed.  Seems like an easy fix, just glad it's not the compressor or the evaporator coil under the dash.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • ryan35205
      Lets Talk Z60 Suspension

      By ryan35205 · Posted

      Did the KYBs keep it the same height in the front? I was concerned that pre-assembled assembly would raise it up an inch to standard non-z60 height.. I guess which it would make the rake 1 inch instead of 2 inches.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      Thank you for keeping the train on the tracks and for a thoughtful engagement. I enjoyed the reflection on a previous stance to refine and improve your position. I like that inquisitive flexibility about you Atlas.    No the process isn't sterile. Hundreds, perhaps thousands of miles of piping, vessels, pumps. Chevron, the people I worked for, were keenly aware that there is a market for what is known as their "ISOCLEAN" line of lubricants. These are lubricants that are the same as those sold bulk that are further processed by filtration to a level your particular application demands. They will filter and package and provide lab documentation as required. Do not kid yourself. Every gallon of oil that goes into a Chevron Turbine, reciprocating compressor, generator is prefiltered and tested before being charged. Lest wise it was when I was there in the plants I worked in.    There are requirements set by manufactures for the cleanliness of the oils used in their equipment. OTR such as CUMMINS has standards shared with customers on this. Commercial interest selling to Ma and Pa do, but don't share that information. Not even upon request but internally, they do exist.    The GM study sited, (Graph from Machinery Lubrication in previous post) only shows "relative" importance.  I find that fascinating. By constructing the graph like this they admit there are dozens of factors in engine life and via scientific method determined the effect of 'relative cleanliness' on engine life not in miles but in 'FACTORS'. This allows a certain amount of reverse engineering does it not?   They even provided some touchstones. Beta 75 as a reference point. Wonderful stuff!!   Smaller blenders CAN and some DO take the time and effort to do better than a refinery or large bulk blender, like Warren Oil, in improving the "in the can" cleanliness. No I don't have a list but testing could generate that information.    Again, but one of several levers we can pull to improve engine life. The simplest is keeping a clean work station while doing your own oil changes.     
    • Mykel544
      New Guy from Oklahoma

      By Mykel544 · Posted

      Thank you. I'll give it a try 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I just spent the last 45K miles doing samples every oil change over more than a full year to get the data for seasons and break-in to broke in.    I found the same thing to be true. Something was always teetering on done or had stepped off the cliff long before the OLM was DOA. In fact, I found about a thousand mile difference between summer and winter. That is during the winter half the OLM was STILL too long. Even the severe schedule was to long in the winter.   Now having done the work I can say I was NOT DISAPOINTED. I saw nothing I didn't already know. Nothing my father hadn't already demonstrated in his 2K OCI's pushing dated iron on dated oils and weak filters to mileages well beyond 300K.   Building on his work through use of Lab testing it wasn't hard to find the correlation between 'sight/feel/odor, the things dad relied on, and test results. Use of current viscosity stable chemistries & filters has pushed that marker for my motors out to 3K summer, 4K winter.    So the early lies were 3K on conventional oil and the lie upon the lie was 7K+. turns out to be off by a factor of two.    So... it is true that modern chemistry has doubled the useful oil life. But the base milage that came from was off by double. It's how good lies work. Partly true, sometimes mostly true so that your meter isn't set off. It also means that non-shear-stable shelf oils are only now as good as the old oils were in their best case scenario.    So the question now is how do we improve on that? Thus the question into cleanliness among the other items listed in the post quoted below.    If this bores you, feel free not to participate.       
    • newdude
      2027 Chevrolet Silverado: Official Discussion

      By newdude · Posted

      Is it though?  Like LTZ, not a high take rate.  Current Sierra has AT4, Denali and Elevation as its main bread winners.  Each trim accounting for 25-35% of sales for Sierra.  SLT makes up about 10-15% at best.        Like others have predicted here for GMC, it will be:   - Pro (equal to WT Chevy)   - Elevation (replaces SLE and SLT)   - AT4 (and X)   - Denali (and Ultimate).  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...