Need backing plates and ebrake hardware for NBS

By bansell
May 6, 2006 in Classifieds (Buy/Sell/Trade)

Recommended Posts

bansell

Posted May 6, 2006

Anyone know where I can get complete rear backing plates with all the ebrake hardware/cables etc for the 99 NBS sierra 1500 4x4? My dads backing plates are rotted out, and all the ebrake HW is junk...

Any of you buy a used rear end and have these parts left over?

Are 99-05 all the same?

thanks

-Bill

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.4k
Total Topics

2.7m
Total Posts
Member Statistics

342,835
Total Members

8,960
Most Online

Newest Member
ballencd
Joined 19 hours ago
Who's Online 6 Members, 0 Anonymous, 468 Guests (See full list)

Latest Articles
- Hummer Turns 25 and GMC Brought the H2’s Yellow Back
  Wednesday at 06:04 PM
- What’s New for the 2027 GMC Yukon and Yukon XL
  Monday at 06:15 PM
- Got a “Service Door Latch” Alert? Fix It in a Minute
  July 9
- GM Recalls Cadillac VISTIQ Over Power-Folding Seats
  July 8
Posts
- 2 speed transfer case optional now?
  
  By Hoginedgewood · Posted 21 minutes ago
  
  Was looking at new trucks online, only the upper models advertise a 2 speed? Maybe I read it wrong.
- Correct way to service 2024 l8t allison trans?
  
  By carkhz316 · Posted 2 hours ago
  
  Yeah, its not an instruction anywhere but instead a unofficial shortcut that some, including myself, use. It does take considerable leverage against the exhaust crossover to allow enough room to clear the pans, but it doesn't strain it any more than normal driveline torqueing of the exhaust pipe and components.
- Hot air constantly blowing through floor vents, drivers side only?
  
  By davester · Posted 7 hours ago
  
  And there aren't any "bellows". There are solid plastic doors the actuators move, which largely seal just by themselves, and then have a strip of foam around the edge to better seal the door. The foam does deteriorate over time, but this is unlikely to be a significant cause of the problem.
- Hot air constantly blowing through floor vents, drivers side only?
  
  By davester · Posted 7 hours ago
  
  are the heater controls set for hot or cold air? If it's set for hot, and say, to get air from outside the cab (vs recirculated air), even w the fan off, air will get pushed through the hvac system, over the heater core and into the cab. Switching it to cold will reduce the temp to whatever it is outside. Switching to recirculate mode (which may mean switching to vents or whatever, read your owners manual), will reduce the amount of airflow through the hvac system.
- Hot air constantly blowing through floor vents, drivers side only?
  
  By dna9656 · Posted 8 hours ago
  
  Prolly diaphragm bellows rotted out. Given the age of your truck.
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 157 members
- diesel 3.0
  
  Open Club · 281 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 213 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  Grumpy Bear
  18
2. 2
  
  Chuck FB
  16
3. 3
  
  newdude
  12
4. 4
  
  OnTheReel
  8
5. 5
  
  Atlas
  8
Show More