Jump to content

Garage Wall systems

Tucson_02Silverado

By Tucson_02Silverado
in The Off-Topic Bar

Recommended Posts

Tucson_02Silverado Senior Enthusiast

Tucson_02Silverado

Posted
Posted

I've been thinking of putting up some type of garage wall system.

 

For the back wall, I will be going with the ClosetMaid Garage ShelfTrack wire shelving system. This wall will have the 18 gal storage containers of crap...er life experiences. I figured that the wire shelving would keep down the dust accumilation, so I wouldn't be eating dust bunnies when I pulled a container off the shelf.

 

On the two side walls, I was thinking about floor to ceiling Whirlpool Gladiator panels. I've also found StoreWall by Storic panels similar to the Gladiator.

 

I was thinking that the "slot" wall system would offer the best long term flexability. But as with most things, the ClosetMaid stuff on the two side walls look good as well.

 

Anyone have experience with either one of these 3 systems? Of course the floor will get it's epoxy coating after the wall system goes up.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      The filtering to wear relationship goes like this:      'Relative Engine Life "Factor" new divided by the factor old. So 8/3= 2.67. That result is the multiplier thus if a motor had an effective life of 100K using a filter with a 45 micron rating at a Beta ratio of 75 then a filter with a micron rating of 10 at a Beta of 75 would improve expected engine life to 267,000 miles.    Wear metals are an indirect indicator. Less is better and the motor lives longer but there isn't a multiplier like there is for filtration so well documented. Most of that has to do with the sensitivity of the wear metals tests themselves. The read a 'slice' of the spectrum but not the absolute values for the entire spectrum. So a general indicator that is used WITH the results of other tests. Two others considered in this post.    There is also the influence of corrosive wear which may be seen in the wear metals but separate from load based or viscosity mitigated indication. It's a small graph but the gray line is wear vs the TBN/TAN crossover. Not as useful as it used to be as there are now new chemistries for acid remediation that don't show up in standard UAO testing. They will catch up or be found liars. Only two possible outcomes, eh?             
    • mikeyk101
      TCM Tuning 6L80E

      By mikeyk101 · Posted

      One thing that comes up over and over is that the torque converters are the weak link. Many of the failed transmissions have the same thing in common. The torque converter grenades and then metal torque converter shards end up destroying the transmission. One of the best things you can do is if your transmission is still fully functional, change out to one of the aftermarket billet torque converters. There are several good choices mentioned in different threads here to make your choice. After that, then you can decide about trans tuning. My trans failed at around 95,000 miles. It got replaced under the GM protection plan. The remanufactured trans comes with a 100,000 mile /3 year warranty. I still have just under 1 year left. So far, so good. As long as it's still working good next year, an aftermarket torque converter is going to get installed early spring. If the trans and OEM torque converter fail by then, I will get it replaced under warranty and immediately have an aftermarket torque converter installed. A warranty replacement trans of a replacement trans will no longer have the warranty so I will bulletproof it from the get go.
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      You got'a be cooking right now. Just looked at the weather map. Yuck!    We are right back to $4 today.    
    • CamGTP
      Gas Prices

      By CamGTP · Posted

      Pushing $4.00 a gallon in most places, still $3.75 in town but it's going to spike tomorrow for sure.   Diesel back up to $4.60-5.00.
    • calgator73
      LCA bolts

      By calgator73 · Posted

      I really appreciate the response.  I guess I was confused about torque angle vs torque angle yield.  The individual bolts don't have a warning on reuse but the part number for the LCA nuts does.   Regarding the purpose of the moog grease fittings on their bolts .. Guessing to reduce possibility of corrosion locking the cams or seizing to the bushing inserts.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...