Jump to content

Does Anybody Have Fuel Line Part Numbers For The 95 6.5 Diesel Tahoe?

jrsavoie

Recommended Posts

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted

If you need any further help,post me the last 8 digits of your VIN and I'll look them up.

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted

BTW Jeff,You sure do like your 6.5's huh?!? :( I seen enough of them at work during the mid-'90's/early 2000's,I can't tell you how many injector pumps we put on those things :fume:

jrsavoie Enthusiast

jrsavoie

Posted
  • Author
Posted
BTW Jeff,You sure do like your 6.5's huh?!? :( I seen enough of them at work during the mid-'90's/early 2000's,I can't tell you how many injector pumps we put on those things :fume:

 

Last eight of the vin SG113169

 

A lot of the injector pumps swapped at the dealers only needed a PMD. For a long time the dealers would swap out perfectly good injection pumps instead of adding a remote mount PMD. I even had our local dealer laugh at my aftermarket PMD and heat sink when I dropped it off. They didn't know what it was.

I've only gone through 2 Injection pumps total on all of my vehicles. I've also run 11% soy since it was available in the mid to late 90's.

I think a lot of the real injection pump problems arose from the lack of lubricity in the newer fuels. The soy raises the lubricity to a higher level than what it was even in the good old days.

Thank You very much.

Do to health reasons, I haven't been able to get the Tahoe torn apart to see just what exactly I need. It's getting air in the lines if it sits for 4 hours or more. If I run the lift pump for 30 or 40 seconds before starting it will stay running. Otherwise it will start and run til the Injection pump gets air in it. Then it's more of a process to start it again.

Other than the drivers door the vehicle is pretty rust free. That door has been replaced once with a used door after it was crashed. The door apparently wasn't in as good a condition as what I was lead to believe.

 

It does make it easy to have spare parts with all these vehicles being pretty much the same.

  • 1 year later...
MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted

Heres the part numbers for you!....

 

15722287 - PIPE;FUEL RETURN REAR

15722284 - PIPE;FUEL RETURN INTERMEDIATE

15721519 - HOSE;FUEL RETURN FRONT

15722221 - PIPE;FUEL FEED REAR

15722273 - PIPE;FUEL FEED INTERMEDIATE **THIS PIPE HAS BEEN DISCONTINUED FROM GM AND IS NO LONGER AVAILABLE**

15721518 - HOSE;FUEL FEED FRONT

 

Other than the one I noted,the rest are all still available from GM.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Gas Prices

      By Atlas · Posted

      $5.19 for regular...
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      My office is slowly filling with Blazer parts. Getting ready to do the big bang of repairs. Intake (second time), water pump, radiator, hoses, and I'm going to re-seal the timing cover where someone went hog wild with silicone. Might as well, because I don't think that's done right.   There's a local tow yard that I didn't realize also has quite the inventory of junk vehicles. This is an old school junkyard. No waivers. Cash only, you were never here if anyone asks. Don't piss off the owner, or you'll end up in the back of one of those cars, headed for the shredder. And if you see something, don't snitch. Cars stacked double high, wasps nests, trip hazards and junk everywhere. I found a few little odds/ends for my Blazer. The $20 I spent was worth the experience alone. But I was never there. What yard?   I officially love/hate this truck. It's so out of my wheelhouse, roughest vehicle I've ever owned. Every. single. repair. -is so hard-fought, everything that can go wrong, goes wrong. Currently in a hate phase, and kind of wish I was closer to sending it down the road with a lucky new owner, to be honest. Preparing for the day when I tear into this thing...lots of pre-funk with Ibuprofen.   Rock Auto sent me a bad reman rear wiper motor. It was a bear to install. The tailgate in these things has about eleventy-billion fastners and pieces and things that need to be uninstalled/moved just to access the shoddy rear wiper motor. The casing on mine was cracked clean through, btw. Nice, GM, nice. SO I got this new motor installed, hit the switch, I see it wig-wag (without the arm installed) and think I'm golden. Reassemble everything. With the wiper arm installed I gave it one final test. Time to clean up and take the other half out to dinner, collect a paycheck, right?   Nope. I hear the plastic worm gear stripping as the arm hung up. Just like my broken motor. Weak/old and shredding itself internally. I can assist the arm and the range of motion is normal, and it parks correctly. It just doesn't have the poop to actually sweep the arm with a blade on it. Oh, hell. Turned the key off and shut the shop door behind me. I get to do that over again, too.
    • BlueV8
      AFM Disabler Question

      By BlueV8 · Posted

      A complete delete is the most thorough mechanical solution, but it is also major engine work. On a quiet truck that is still under extended warranty, opening the engine purely as prevention is difficult to justify. A plug-in disabler stops commanded cylinder deactivation, but it does not remove or repair the collapsible lifters, so it should not be treated as failure insurance. I would keep the oil full, document the maintenance, and have any persistent tick, misfire, or loss of power diagnosed promptly. If the engine eventually has to come apart, that is the logical time to compare an OEM-style repair with a complete delete. The right choice depends on the truck’s symptoms, warranty status, expected ownership period, and whether the engine already needs to be opened. We explain that decision in more detail here—full disclosure, this is our own guide: https://www.bluev8.com/blogs/news/do-you-actually-need-an-afm-disabler   One exception: some 2021 L82/L84 trucks have RPO YK9, meaning cylinder deactivation was already disabled in the factory ECM; on those trucks a plug-in disabler is redundant, although the AFM/DFM hardware remains inside the engine.
    • mark249
      Help purchasing a touch screen digitizer

      By mark249 · Posted

      Brought my 2015 Colorado into the dealership to check my touch screen issues, had that ghost touch thing happening. They said I needed a new touch screen and they could either order me one for $500. The lady at the service deck was nice enough to tell me I could order a touch screen online for less, she did stipulate that the touch screen had to be factory OEM, you can't pair an aftermarket screen to my radio seeing it was 2015, it had to be a GM factory OEM only. I found a few on Amazon and Ebay by the numbers on the back of the old screen, DJ080PA-01A GM# 22740886, Some said "OEM" in the description and others just said "Replacement". Would a replacement be the same as a OEM as long as it had the same numbers on the back of the screen? In some of the descriptions they also show different brand names but same numbers, is that an issue?  
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      I have both but typically use the 4 legged walker (wheels on front, ski's on back).   The four wheeler is starting to be used on "longer" outdoor walks.  The 4 legged walker is particularly helpful in practicing good walking posture.  Both of my knees are at different stages of recovery and I'm trying to not develop poor habits.  I can actually manage with a cane but it's very difficult not to favor one leg over the other.  My PT recommends I continue with my 4 legged walker for a while.  Yesterday was four weeks since my last knee replacement and I'm excited about my progress to date.  It has been a hell of a rough journey so far but it is exciting to witness  systematic and continuous improvement.  I went for years watching the decline of my "mobility".  It seems that everyday now I am alerting my wife to something I can do now that I couldn't a day or two ago!  I encourage anyone facing the prospect of knee replacement to share any concerns with others who have had the surgery.  It isn't an instant fix but rather is a considerable amount of short term pain for long term gain.  Recovery time and pain levels vary for individuals post surgery but the end results are typically very positive and I've never encountered anyone regretting having had the surgery. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...