Jump to content

Louie210 Black on Black 14'Silverado

Chico210

By Chico210
in Member Build Threads

Recommended Posts

Chico210 Enthusiast

Chico210

Posted
Posted

RC 2" leveling kit

20x9 fuel Mavericks

33x12.5x20 Lexani mud tires

50" led bar with keyfob control

RC mounting brackets

Limo tint.

Crew cab 6" running boards.

Trifold bed cover.

Led bed lights

Couldn't pass a deal for the rims and tires thanks to good ole' craigslist.

looking for a lift kit just undecided.

F03713EF-E06A-4BDE-99D4-26D02EE75387.jpg

 

85FFE1F9-BA6D-4C9B-BFF9-F94473B3944A.jpg

 

 

837ED54B-71DC-445A-BD6A-DBF8738CB165.jpg

Strykers_Inc Enthusiast

Strykers_Inc

Posted
Posted

Yep.Yep.

 

Is that the curved lightbar. I have the same mounts in black and a curved 50" bar. Not installed until way later. Working on audio right now and want to have my electrical system completed before anymore of a 12v draw.

  • 2 weeks later...

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Sdid
      2020 Silverado 1500 8speed gm needs to recall transmission

      By Sdid · Posted

      I have A 2020 1500 5.3 8 speed. LTZ. Transmission problems since 60,000 miles. Started when I go to store in morning to get my morning coffee before work leave truck running get back in put it in drive/ rev no movement step on gas a little slams into gear. Put in neutral step on gas little shake then put in gear and gose.  Shut truck off start .. ok now at stop light stop truck after a few seconds feel a little kick if that doesn’t happen stuck in 3/4 gear shut truck off wait few seconds and start usually ok again. If you down shift manually ok as long as you get into 1st before stop. If not it kicks . I WANT A NEW TRANSMISSION. Now I want a new truck it just hit 80,000 IDK IF ILL BUY CHEVY CAUSE THEY STILL HAVE THE PROBLEM AND REFUSE TO RECALL . Oh I’ve changed the fluid and filter 3 times now. And yes used mobile 1 not ac/delco cause it’s not meeting the requirements that mobile is did use ac/delco filter 
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      Of course refrain from political debate but I myself have very dismal hope for what is all going on up here every where we turn so I nodded my head when I saw this joke.     
    • diyer2
      Navigating senior years.

      By diyer2 · Posted

      I'm looking at carpal tunnel surgery on my left hand and lumbar fusion. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      While waiting for parts I have been working on installing the AC compressor, new accumulator, and orifice tube. Also changed out the high side ball valve (original). The orifice tube that was in there wasn't too bad. Slightly dirty, a little bit of junk, but not blocked. Glad I changed it out.   The accumulator, which should have been a 5 minute job, may have just burned $50. Put some PAG in it, wrote the date and mileage on the side, fresh o-rings and gooey'd up the threads and rings with Nylog. Got everything connected and snugged and was going to vacuum down the system, and....   My manifold gauge won't fit on the port. It's not an R12 service port. It LOOKS like an R134 service port but the diameter is a hair too large. There's a sticker on the accumulator that says it's designed to be used with R12 and R134a systems only. So it's not R1234yf. Even if I reduced the diameter slightly with a file, the shoulder on the port is too large so the quick-connect valve won't lock on. I'm stumped. It's going back, and 50/50 on if they'll give me a refund.   Also, I did a fuel pressure test.... Key on, the gauge spikes to about 60psi and quickly bleeds off, like 2psi per second. The fuel isn't going into the plenum, no smell, starts fine, so I'm guessing there's a bad check valve in the pump and the fuel is just draining back into the tank. oh, hell. But, it shouldn't be a problem, pump primes just fine and the truck starts right up. It just means I can't really ever use fuel pressure to verify a leak at the injector or intake.
    • No F-bdy Bs
      SERCICE ESC message?

      By No F-bdy Bs · Posted

      Got this yesterday out of nowhere. Truck is a 25',6.6 gasser with 8k miles.  Only semi anomaly is that the truck had been sitting, uncranked for 6 days. Elec Stability Control showed immediately upon cranking, not while driving. No drivability issues, just the message. Battery didn't seem to be weak when cranking over.  I drove it, killed it, let it sit a few hrs with no avail.  Truck is 100% stock. No damage. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...