Jump to content

2011 Silverado Remote Start?

Austin Saunders
 Share

Recommended Posts

Austin Saunders New Member

Austin Saunders

Posted
Posted

So i purchased a key fob online that has the remote start button. Looked online and says if you have the Code AP8 on the top of the sticker in the passenger glovebox your truck has remote start.

 

Had the dealer program the remote and the locking doors work fin but the remote start does not. The signal is sent to the truck because the lights flash just like it does when it is supposed to start. I asked the dealer, they told me that i do not have the remote start feature but im reading everywhere online that the code AP8 means your truck has the feature. Any help on this would be much appreciated.

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted

AP8 is NOT the remote start code, AP3 is for remote start, AP8 is the remote start prep package, which means you can add remote start, however just buying a fob and programming it will not turn on the remote start feature, you must purchase the GM remote start accessory package, the package gives you 2 fobs, a decal to place in the glovebox, and most importantly it gives you an unlock code that the dealer needs, with this code the dealer calls GM techline and gives them the code, techline then gives the dealer the proper reprogram code to turn the remote start feature on.

  • Like 3
MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted (edited)

Heres a bulletin on adding the remote start....

 

#PIT4082J: Information On Adding The GM Accessory Remote Start Kit - (Aug 1, 2012)

 

Subject: Information On Adding The GM Accessory Remote Start Kit

 

Models: 2007 - 2013 Cadillac Escalade, ESV, EXT 2007 - 2013 Chevrolet Avalanche, Silverado, Suburban, Tahoe 2007 - 2013 GMC Sierra, Yukon, Yukon Denali, Yukon XL, Yukon Denali XL

This PI was superseded to update recommended field, model and model years. Please discard PIT4082H.

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

 

Condition/Concern:

The following is additional information on adding the GM accessory remote start kit.

Note: This does not apply to the bi-directional (2-way) remote start kit.

 

Recommendation/Instructions:

Vehicles must have the extended remote start option RPO (AP8) in order to add the GM accessory remote start kit. This kit is only available on automatic transmission models. Every step of the instruction sheet needs to be followed exactly in order for the remote start to operate properly. Here is a brief summary of what needs to be performed.

  1. The BCM needs to be programmed for remote start by contacting the Techline Customer Support Center (TCSC) @ 1-800-828-XXXX and having them add the remote start function to the VIN number so the BCM can be reprogrammed by TIS2WEB. After reprogramming the BCM, the vehicle will need to be shut off for 1 minute and then the SIR restraints ID will need to be setup by using the "Set up SDM primary key in the BCM" under module setup category in the BCM.

    Note: Once the remote start option is added to the VIN at TCSC, the option will always be available even if the BCM is replaced or re-programmed at a later date.

    Important: The Brake Pedal Position (BPP) sensor MUST be re-calibrated anytime the BCM is reprogrammed on 2012 or newer vehicles.

  2. The remote start instructions state that the BPP sensor will need to be re-calibrated. Starting with the 2012 Model year a BPP sensor was added to the trucks and the BPP Re-Calibration MUST BE PERFORMED. However, the 2007-2011 trucks are not equipped with a BPP sensor so the re-calibration cannot be performed and is not necessary.
  3. The Theft Deterrent Module will need to be SPS programmed with the remote start option selected.

    Note: Please select TDM in the controller list and not VTD relearn when re-programming the TDM.

  4. Clear all codes in all the modules on the vehicle.
  5. Program the new remotes (supplied in the kit) to the Remote Control Door Lock Receiver.
  6. Installation complete.

Troubleshooting: Remote Start Inoperative:

  1. If the vehicle is equipped with RPO UK3 Steering Wheel Controls with the Drivers Information Center (DIC), make sure remote start option is turned on in the DIC.
  2. Make sure the Remote Control Door Lock Receiver is calibrated for the remote start option. Most vehicles with the RPO AP8 should already be programmed for remote start.
  3. Make sure the vehicle has adequate fuel (above a 1/4 of a tank).
  4. Make sure there are NO DTCs.
  5. Check for any of the disable conditions listed in SI Document ID# 1689813.
  6. If B1370 code is set and the RVS is inop then verify that the TDM has been programmed for the RVS selection.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

Edited by MS3DALE
  • Like 1
  • 3 weeks later...
carkhz316 Enthusiast

carkhz316

Posted
Posted

MS3DALE is absolutely correct. My brother just went through with this on his '11 2500. Absolutely no way around buying the GM package deal if you want a factory remote start. Oh well, at least he has 3 fobs with remote start, and his original one without.

  • 3 years later...
Steven Tkachuk Enthusiast

Steven Tkachuk

Posted
Posted
 

AP8 is NOT the remote start code, AP3 is for remote start, AP8 is the remote start prep package, which means you can add remote start, however just buying a fob and programming it will not turn on the remote start feature, you must purchase the GM remote start accessory package, the package gives you 2 fobs, a decal to place in the glovebox, and most importantly it gives you an unlock code that the dealer needs, with this code the dealer calls GM techline and gives them the code, techline then gives the dealer the proper reprogram code to turn the remote start feature on.

I've checked everywhere trying to get the "GM Remote Start Accessory Package"  I have called several dealerships & am told that that part # is discontinued.  No one will help.  Can I buy the OEM Key FOBS elsewhere & have a dealership work on the unlock code part?  

 

Best advise to proceed?

 

Thanks, 

 


Steve

Steven Tkachuk Enthusiast

Steven Tkachuk

Posted
Posted
 

Heres a bulletin on adding the remote start....

 

#PIT4082J: Information On Adding The GM Accessory Remote Start Kit - (Aug 1, 2012)

 

Subject: Information On Adding The GM Accessory Remote Start Kit

 

Models: 2007 - 2013 Cadillac Escalade, ESV, EXT 2007 - 2013 Chevrolet Avalanche, Silverado, Suburban, Tahoe 2007 - 2013 GMC Sierra, Yukon, Yukon Denali, Yukon XL, Yukon Denali XL

This PI was superseded to update recommended field, model and model years. Please discard PIT4082H.

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

 

Condition/Concern:

The following is additional information on adding the GM accessory remote start kit.

Note: This does not apply to the bi-directional (2-way) remote start kit.

 

Recommendation/Instructions:

Vehicles must have the extended remote start option RPO (AP8) in order to add the GM accessory remote start kit. This kit is only available on automatic transmission models. Every step of the instruction sheet needs to be followed exactly in order for the remote start to operate properly. Here is a brief summary of what needs to be performed.

  1. The BCM needs to be programmed for remote start by contacting the Techline Customer Support Center (TCSC) @ 1-800-828-XXXX and having them add the remote start function to the VIN number so the BCM can be reprogrammed by TIS2WEB. After reprogramming the BCM, the vehicle will need to be shut off for 1 minute and then the SIR restraints ID will need to be setup by using the "Set up SDM primary key in the BCM" under module setup category in the BCM.

    Note: Once the remote start option is added to the VIN at TCSC, the option will always be available even if the BCM is replaced or re-programmed at a later date.

    Important: The Brake Pedal Position (BPP) sensor MUST be re-calibrated anytime the BCM is reprogrammed on 2012 or newer vehicles.

  2. The remote start instructions state that the BPP sensor will need to be re-calibrated. Starting with the 2012 Model year a BPP sensor was added to the trucks and the BPP Re-Calibration MUST BE PERFORMED. However, the 2007-2011 trucks are not equipped with a BPP sensor so the re-calibration cannot be performed and is not necessary.
  3. The Theft Deterrent Module will need to be SPS programmed with the remote start option selected.

    Note: Please select TDM in the controller list and not VTD relearn when re-programming the TDM.

  4. Clear all codes in all the modules on the vehicle.
  5. Program the new remotes (supplied in the kit) to the Remote Control Door Lock Receiver.
  6. Installation complete.

Troubleshooting: Remote Start Inoperative:

  1. If the vehicle is equipped with RPO UK3 Steering Wheel Controls with the Drivers Information Center (DIC), make sure remote start option is turned on in the DIC.
  2. Make sure the Remote Control Door Lock Receiver is calibrated for the remote start option. Most vehicles with the RPO AP8 should already be programmed for remote start.
  3. Make sure the vehicle has adequate fuel (above a 1/4 of a tank).
  4. Make sure there are NO DTCs.
  5. Check for any of the disable conditions listed in SI Document ID# 1689813.
  6. If B1370 code is set and the RVS is inop then verify that the TDM has been programmed for the RVS selection.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

DO you know where I can get the GM Accessory Remote Start Kit?  Every deal I've called will only tell me that the part has been discontinued & I end up in a vicious circle between service and Parts.  

 

Steve

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted
1 hour ago, Steven Tkachuk said:

DO you know where I can get the GM Accessory Remote Start Kit?  Every deal I've called will only tell me that the part has been discontinued & I end up in a vicious circle between service and Parts.  

 

Steve

Steve...Can you post me the last 8 digits of your VIN? They have discontinued some of the kits, but some are still available that may work for you, but I need your VIN to verify.

Steven Tkachuk Enthusiast

Steven Tkachuk

Posted
Posted
2 hours ago, MS3DALE said:

Steve...Can you post me the last 8 digits of your VIN? They have discontinued some of the kits, but some are still available that may work for you, but I need your VIN to verify.

Sure Thanks!  The last 8 :  BZ296670

 

The Part Number that I have been trying to get is 17801236

 

Steve

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted
16 hours ago, Steven Tkachuk said:

Sure Thanks!  The last 8 :  BZ296670

 

The Part Number that I have been trying to get is 17801236

 

Steve

Steve.….

 

17801236 is discontinued, however I called our local GM-ADI (which is GM's accessory distributor installer in our area) its been replaced by part# 22970855

Steven Tkachuk Enthusiast

Steven Tkachuk

Posted
Posted

Ok, I looked up the part on several parts websites & most of them has said that this part doesn't work for my truck.  Do know if this part comes with the Authorization code for GM? I'm hesitant to buy it until I can get some verification.  Should I take this part number to the dealer & have them verify that its correct?

 

I just dont want to shell out a bunch of $$ if it doesn't work.   

 

Steve

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted
8 minutes ago, Steven Tkachuk said:

Ok, I looked up the part on several parts websites & most of them has said that this part doesn't work for my truck.  Do know if this part comes with the Authorization code for GM? I'm hesitant to buy it until I can get some verification.  Should I take this part number to the dealer & have them verify that its correct?

 

I just dont want to shell out a bunch of $$ if it doesn't work.   

 

Steve

Part# 22970855 replaced part# 17801236, Your local dealer can call their ADI as well to verify if you want.

newdude Senior Enthusiast

newdude

Posted
Posted

Its discontinued.

 

GM shows no superseding part #s for 17801236 in EPIC either, nor does GM show 22970855 replacing it.    

 

Their engineering notes show no superseding number either:  

 

Quote

PART NUMBER 17801236. TRANSMITTER PACKAGE. IS DISCONTINUED. FOR REPLACEMENT TRANSMITTER. USE PART NUMBER 22936098

 

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted
10 minutes ago, newdude said:

Its discontinued.

 

GM shows no superseding part #s for 17801236 in EPIC either, nor does GM show 22970855 replacing it.    

 

Their engineering notes show no superseding number either:  

 

 

22970855 is the number we've used here at the dealership, it's worked fine.

  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,894
    Total Members
    8,960
    Most Online
    TopBo
    Newest Member
    TopBo
    Joined

  • Who's Online   0 Members, 0 Anonymous, 1,343 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • davester
      New to Me 2010 SLE (Quirks, Issues)

      By davester · Posted

      not all plugs will be used.  gm uses more generic harnesses that support most/all options, and if your truck doesn't have a specfiic option, the plug won't be used (commonly will have a dummy insert in the plug , or it'll be taped up, but some may just be left as is).  But it's sldo possible some p.o. has installed the wrong/cheaper parts that aren't correct for your vehicle...
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      First off, I'm not trying to just get easy advice/fixes for the issues I've noticed so far.  I'll be combing through the site via searches and such, and if past experiences are any indication, should find what I need.  For the sake of conversation, though, I figured I'd post the handful of things I've noticed in the 12 hours since buying my 2010 SLE CCSB.     Indicator lights: Airbag and TPMS.  The tire pressures aren't reading for any of the wheels, so I'm pretty certain the sensors were either removed, are damaged, or are otherwise inoperable.  I used to mount and balance tires 25 years ago but am pretty much ignorant when it comes to TPMS.  My 2006 didn't have the sensors and this might be the fourth vehicle I've owned that does.     Radio: Rear speakers aren't working.  I removed the driver's side rear door panel and checked the speaker and wiring.  I also removed the sill and b-pillar covers to check the wiring.  A few minutes of Google Fu showed that this is potentially a head unit issue.    Switches: Power mirrors don't turn left/right.  I ordered replacement driver's door switches that should arrive tomorrow.  The windows and locks work but it was only about $20 for all of them.  The driver's side rear window switch lets the window down but won't put it back up.  I think the passenger rear doesn't work at all.  In the coming days/weeks, I'll break out my multimeter to check all of that.   Unknown wiring harness: There's a box attached to the front driver's side of the engine compartment, right where the second battery shelf is located.  There are three plugs, one of which looks like it fits a standard headlight-style bulb (9007 or similar).  It doesn't look like it's plugged into anything.  I'll do some digging and if I don't see anything elsewhere on the site, post some pictures here.   Unknown plugs on brake booster: There are at least two female plugs on the brake booster that aren't being used.  I think it might be a replacement/aftermarket, so maybe those are used for a different application, as there don't seem to be any unplugged harnesses and no indicator lights are on.   Little squeaks when turning: Sounds almost like a bushing around the bed of the truck.  I'll have to pay close attention as I get more familiar with the truck.   Clunk on acceleration: possibly the infamous drivetrain clunk.  My 2006 had it and I'm just not familiar enough with this truck yet to fully grasp what it is.   Anyway, my apologies for the vague and all over the place post.  This truck is new to me, and it's been four years since I drove my 2006.  With 200k miles, I know I'll need to learn this truck quickly to avoid having any major issues, despite being confident it's got much more life to it.  My 2006 had nearly 320k on it when I parked it (nearly 300k of which I put on the truck), and it was still drivable then, though I suspected the head gasket might have blown.  I'd hoped to have that truck back by now, but it's gone forever, as I detailed in my reintroduction thread.  
    • lowrider
      Range RA007 DFM Module

      By lowrider · Posted

      I always drive in Sport mode. With more driving, I am finding the initial response when accelerating is much quicker now🖕 Lou
    • Tyler Gibbs
      2022 2500HD with a new RSI SmartCap

      By Tyler Gibbs · Posted

      Is it an optical illusion in the pic or is the truck really squatting that much horribly?
    • fm2176
      It's Been a Long Time...

      By fm2176 · Posted

      My initial introduction was here.  It's hard to believe that I last posted in February 2013, having just deployed to Kyrgyzstan.  Since then, I've retired from the military and the 2006 Sierra SLT Z71 that first brought me to these pages was lost.  I went forward to Afghanistan in March 2013 and did a lot of sitting behind a computer on brigade staff.  Within 18 months of getting back to the States, I was selected for Drill Sergeant duty, after which I moved back to Virginia (my home state and where I served from 2004-2008).  That '06 Sierra did a lot of driving between Louisiana, Georgia, and Virginia, and ended up with nearly 320k miles by 2022.  By then, the registration had been expired for a couple of years, but the pandemic had all but eliminated tickets for such transgressions.  Admittedly too, I usually drove my wife's SUV or son's car the 2-3 times a week I had to report to work.  Teleworking sure was fun while it lasted.   I started my retirement leave four years ago and stored the Sierra at my sister's house.  A big mess was made when her fiancé passed while she was taking care of business out-of-state in late-2024, and his son pretty much mismanaged everything to do with the estate.  Even so, I was assured that my truck was safe... until it wasn't.  I found out that my truck had been scrapped about four months after the son took over everything.  There's nothing I could do; I'm 1000 miles away and it was technically abandoned property since he'd even trespassed my sister from her own house (she had no claim to it as she wasn't married, and the fiancé was the sole owner).     Anyway, today I got my second Sierra.  This is a 2010 SLE 2WB CCSB with a little over 200k miles on it.  It's got the 5.3L I'm familiar with and should handle what I need it for.  Hauling stuff that won't fit in the Transit Connect (yep, I sold out, but that's the wife's vehicle) and towing a few times a year tops.  The price seemed decent, considering how much people sell their trucks for in the Deep South: $4500.  I've seen similar trucks listed for more than double that.  I got it from a coworker who left his tag on until we transfer the title next week (Louisiana requires a notary for transfers), so I've been driving it all day.  The rear speakers don't work, which is one of the things that brought me back to these forums earlier.  I can't say how active I'll be as a poster, but I'll be scouring the archives while I find out every little thing I can about the 2010s and particular nuances/problems with my truck.   It's definitely not a GMC, but I got another Willys Jeep a few months back as well, so I'm almost at the same place I was when I first joined gm-trucks.com.  My old 1960 DJ3A was sold back around 2010 or 2011; my current Jeep is a 1946 CJ2A.  So, I've got a slightly newer GMC and a much older Jeep.  I kind of wish I still had that F-250 I had way back when too.  The Dakota is long gone and was technically my brother's truck, though I had it registered and insured.  The F-250 had to go when my grandmother's house was foreclosed on due to mismanagement around 2012 or so.     Hopefully anyone that made it this far isn't too annoyed.  I tend to be long-winded, but I'll be doing more reading than posting in the coming months.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...