Jump to content

Interior swap

08gmc17
 Share

Recommended Posts

  • 1 month later...
  • Replies 84
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

08gmc17
08gmc17
Andrew_01
Andrew_01

Did you end up finishing this swap? Would love to see the finished product. Also, what paint did you use to paint the interior and did it flow with the high country interior? 

08gmc17
08gmc17

Posted Images

Daniel620 New Member

Daniel620

Posted
Posted (edited)

I wonder what kind of wiring mess you wil have to deal with or the dash, I’ve been thinking about doing the same for a long time but, I just don’t have the time to mess with the dash, I hope you do great, keep us posted

Edited by Daniel620
  • 5 months later...
  • 4 months later...
Monty59 New Member

Monty59

Posted
Posted
On 11/25/2018 at 8:20 PM, 08gmc17 said:

Better looking seats, center console, dash and steering wheel, and bc I can lol i like custom stuff 

Agreed 

  • 2 weeks later...
Mikebtte Enthusiast

Mikebtte

Posted
Posted
4 hours ago, 08gmc17 said:

Got the seats and center console in but haven’t had a chance to install the dash

Cool. No pressure, but we are waiting on you? Kind of like the guinea pig before the rest of us jump in.

08gmc17 Enthusiast

08gmc17

Posted
  • Author
Posted

If you do the dash you’ll either need to swap all the computers so you can use the electronics or get with Dakota digital and have them put gauges in the cluster. I wish I went with needles but I still like this look. The center has boost and fuel psi 

Mikebtte Enthusiast

Mikebtte

Posted
Posted
16 minutes ago, 08gmc17 said:

Thing holding me up on the dash is the airbag. Need to make sure it works

I have considered looking into putting a steering Wheel from a newer GM truck into my older unit. Let us know what you figure out. Might need a steering wheel interface for the controls. Easy enough to do a relearn.

08gmc17 Enthusiast

08gmc17

Posted
  • Author
Posted
3 hours ago, Mikebtte said:

I have considered looking into putting a steering Wheel from a newer GM truck into my older unit. Let us know what you figure out. Might need a steering wheel interface for the controls. Easy enough to do a relearn.

Yeah I have a steering wheel also, I might try that as well not sure.

C5E87CA9-7AF9-4307-9664-7C45792EDE7E.jpeg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,938
    Total Members
    8,960
    Most Online
    C. Hart
    Newest Member
    C. Hart
    Joined

  • Who's Online   4 Members, 0 Anonymous, 511 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      287,500 Mile Service   8/13/2026   Reset Fuel Trims   Since the work done in the previous post there was a good improvement in response in all areas except right after a fill up where the LTFT would go -20%+ for about four miles while the STFT was near neutral. Before the work they both went very negative for a few miles after a fill up but act normal thereafter.    We did a systems check of the vapor recovery system for functionality and ability to hold a vacuum. That checked out fine. But this doesn't mean the charcoal canister is dead in the water. Testing that is next up. For now the reset of the fuel trims.    I intentionally shorted the fill exactly two gallons to eliminate any chance of filling the canister. On start up the trims were behaving normally until I got up and rolling where the LTFT went -10 / -11%% but the short was + 2 to 0%. Within a mile the the STFT offset the LTFT and by 2 miles they were neutral. HUGE improvement but still not hunky-dory.    I'll watch them for a few days. Perhaps another tank where I will fill completely to 'first click' and compare. Meanwhile on the hunt for a new canister and I'll toss another purge value at it for good measure. Pending the outcome of the canister test that is. Progress of any kind is welcome.    Fuel economy improvement with bringing hole #3 back to the living was a noticeable bump to the positive. Even on the few miles I drove after the refill I already see another bump up by the trims reset.     She's purring like a kitten with a warm bowl of milk.    BTW, adding 50 rpm to the idle took the majority of the negative timing out on cold start up and leaned the cold idle. No longer burbles in the cat. What a dumb way to heat a cat.      
    • OnTheReel
      Post your UOA, (used oil analysis) here

      By OnTheReel · Posted

      Yeah, shame I can’t really get that filter easily anymore. Running a PureOne. Your fave!    TAN would be neat to see. Confirmation I ran it too long probably. 🤣
    • superdave160
      Roll up bed cover experiences

      By superdave160 · Posted

      My son and I both bought new trucks in 2017. Both of us immediately put Truck Covers USA American Roll Covers on our trucks. My son still has his truck and it never sees the inside of a garage. We live in Alabama, so not much snow. My truck was my daily driver and was in the garage when I wasn't driving it or at work. No issues with either cover even after almost 9 years. About a year ago I sold my truck to my brother and bought a 2025 Silverado 2500. The second thing that I put on that truck was a new Truck Covers USA cover. They are very well made and have a very positive locking system. I looked at a Retrax and my concern was the way that the cover locked to the rail. BTW, the first thing I put on the new truck was step bars. Those new trucks are high!
    • superdave160
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By superdave160 · Posted

      The Allison 10 speed torque converter doesn't "lock up" like the previous transmissions. It has 4 operational modes; open, slip, transition from open to slip; transition from slip to open. I have an Edge CTS3 monitor and I monitor transmission torque converter slip. Step on the gas and you get a little slip. Take your foot off the gas and you get a little negative slip. I have not found a way to display the torque converter mode beyond that. My Edge CTS3 also displays something that our trucks should already display, the current gear. I also monitor throttle body position and engine load. If I see the engine load getting too high, I'll manually drop a gear.
    • Grumpy Bear
      Post your UOA, (used oil analysis) here

      By Grumpy Bear · Posted

      Nice result. Your filter is working well  I'd have like to have seen the acid number for this sample. Curious type that I am. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...