Jump to content

Wheel hub size

808 HI

By 808 HI
in Modifications, Wheels & Tires

 Share

Recommended Posts

808 HI Enthusiast

808 HI

Posted
Posted (edited)

So I'm trying to order a custom pair of wheel spacers - 6mm/ 0.25" 78.1mm hub centric to 78.1mm wheel centric. The vendors argument is that 6mm is too thin and recommends 10mm, I spoke to another OP here that ordered a set from the same vendor I'm using with the same spec except that his new wheel bore size is 106. My only issue is that I think the 10mm will make it stick farther in front to notice that the front wheels poke more. Vendor says he can make them at 6mm but if it doesnt fit then I wouldn't be able to return and there pricey for a pair delivered at $100. Does anyone know how far the T1 factory hub sticks out to confirm this ?

Edited by 808 HI
808 HI Enthusiast

808 HI

Posted
  • Author
Posted (edited)

Pulled the trigger and went with 10mm and instead of just placing them on the front, I was afraid that it might noticeably stick out farther than the rear so I ordered 4. My new concern is, I want to do this right and replace the wheel studs with longer ones to compensate the spacers but I found no details on extended lug nuts for these trucks. Vendor claims that running 10mm is fine on the factory studs and is long enough to handle. This is supposedly common issue with T1 owners and is his solution to fitting aftermarket wheels other than running adapters. Has anyone ran 10mm with no issues and does anyone know were I can get extended wheel studs ?

Edited by 808 HI
mafd2 Senior Enthusiast

mafd2

Posted
Posted

First off, what is it you are trying to do and why are you wanting spacers? What wheel are you running and what's the bore of the wheel?

808 HI Enthusiast

808 HI

Posted
  • Author
Posted
2 hours ago, mafd2 said:

First off, what is it you are trying to do and why are you wanting spacers? What wheel are you running and what's the bore of the wheel?

 

I got a set of factory reproduction 24s and the shop who installed them used a 6mm non hub centric spacer to clear the calipers. I plan to swap it with hub and wheel centric spacers. Bore size is 78.1. 

  • 2 years later...
Transient Senior Enthusiast

Transient

Posted
Posted

Dorman is one of the largest lug suppliers to auto manufacturers.  They have all sorts of info, but you gotta have access to their catalog.  It's been over a decade since I've looked this info up on GM trucks since I installed spacers on my 2007 Tahoe.  There is a possibility that a longer lug may not be available, especially this early in the game.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,903
    Total Members
    8,960
    Most Online
    RyGuy43
    Newest Member
    RyGuy43
    Joined

  • Who's Online   1 Member, 0 Anonymous, 473 Guests (See full list)

  • Latest Articles

  • Posts

    • davester
      2015 Silverado 3500 right rear turn indicator failure

      By davester · Posted

      consider doing electrical testing?  I would guess some power or ground wire/connection has a problem.   alldata.com has wiring diagrams, connector pinouts and diagnostic procedures you can use to find where the problem is.
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL
    • Chuck FB
      Tire pressure for 37s

      By Chuck FB · Posted

      First off you mentioned "Toyo Says" and then gave the pressures 45/50, was this some person at the tire shop that pulled those numbers out of his head ?   Now of course I can't know your exact axle weights front and rear, however I have much the same pickup as yourself other than not knowing your starting weight as per the pounds the truck rolled out of the factory at due to the options yours did or didn't come with or what you have added beyond the extra tire weight. The correct way to know 100% where a person is at is by weighing each axle with the typical weight the vehicle is driven with and that means taking into account passengers and making sure you figure in a full tank of fuel and a little grace for whatever you may put in the bed "groceries" !    I am looking at and not that it really matters as all the tire companies use the same charts anyway, but I am looking at the comprehensive Toyo tire chart in the section that your tire falls under and I know it sounds confusing but your tire is not an LT metric tire like your factory tire but instead because its a standard inch measured tire its under a different category called an LT floatation series tire. That makes a difference as LT metric tires they don't want to see run below 35 psi at highway speed where as with the LT floatation series it can be run down to 25 psi on the highway as long as the weight on the said size of tire is agreeable with or less than that minimum 25 psi. It blows many people away that how is this physically possible, an empty truck for one thing and larger tires with the same size wheel diameter have a lot more air volume so they can carry the same weight as the smaller tire with less air pressure.    So my truck, I have the stock 275/65R20 wheels and tires and I have a bit of weight in the box with a bak flip cover and a rubber bed mat and some tools and spare gas. The front of my gas truck weighs a bit more than some trucks of the similar spec due to double batteries and alternators. However with full fuel and just me in the truck I am weighted such that I can run 40 front and 35 rear and so that is what I have done since day one.    If I base your truck at or slightly below the weight of my truck, in theory with your tires going by the tire chart you might be right around a minimum of 30 pounds front and 25 pounds rear. Of course that would hit pretty much minimum cold inflation pressure one could run with that tire size and a near empty truck. If you have access to an accurate weigh scale to do individual front and rear axle weights I would suggest you do that and make sure your topped up with fuel and whatever else in the truck before you weigh it and then you will have a great starting point to work off of and figure out what your bare minimum pressures are you can safely run. If you do much in the way of hot weather high speed driving, bumping up a bit for a safety margin is never a bad idea but just depends on what type of driving you do. I will include the Toyo chart and the floatation series sizes start on page 31. Without a doubt at these pressures I am speculating at minimum wise for your truck, it would most certainly ride very different then it did when you were using 55 lb front and rear.     https://www.toyotires.com/media/pxcjubjs/application_of_load_inflation_tables_20200723.pdf
    • Snowcamo
      Possible lifter tick after DOD delete

      By Snowcamo · Posted

      Take an automotive stethoscope to the vacuum pump. Iirc those tick as well. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...