Jump to content

3.5 inch lift. Tire sizes??

Tyler Shelley
 Share

Recommended Posts

Tyler Shelley Enthusiast

Tyler Shelley

Posted
Posted

I have a 20 Sierra Elevation with a 3.5" Rough Country Lift. I swapped my factory wheels with a co-worker for some 20x10 with a -24 offset. He has some "what looks small" 285/55 R 20 tires on it know. What tire size do you recommend. My main question is what is the largest tire size I can run 

Screenshot_20200120-195328_Gallery.jpg

Dunn Senior Enthusiast

Dunn

Posted
Posted

look at thread below yours with 3' RC lift by chris walker

Flatblack83 Enthusiast

Flatblack83

Posted
Posted (edited)

Depends on do u want taller or wider..?  On chevys they go to 295/60/20 =34x11 or 305/55/20 =33.5-12.50 both these sizes are popular on here. Some fit 35s but trim.  So on yours they use a little smaller with the wheel well shape. I'd measure it and see is a 295 60 would fit. That gives u a little width plus the heigth.

 

 

Edited by Flatblack83
Tyler Shelley Enthusiast

Tyler Shelley

Posted
  • Author
Posted
14 hours ago, Flatblack83 said:

Depends on do u want taller or wider..? Go to 295/60/20 =34x11 or 305/55/20 =33.5-12.50 both these sizes are popular on here.

 

I have 295 60s with a 3 inch on stock 20s, no rub.

I was looking into 295/60R 20 but i dont have factory wheels. My wheels have a -24mm offset. I think I will buy a set of that size and try them. They are barely wider than what I have but taller than what I have now. The hight is what I'm  after. The width is what is worried about. 

Tyler Shelley Enthusiast

Tyler Shelley

Posted
  • Author
Posted
3 minutes ago, Flatblack83 said:

Take a look at the custom offsets gallery,  lots of wheel n tire combos on there.

I looked at them. They have a lot for the previous gen trucks but they dont have a lot for this gen. If they do, I can't find it. I traded my factory wheels for these with my co-worker. I can trade back with no problem, but I really like the way the wheels look, but the tires look to small

Flatblack83 Enthusiast

Flatblack83

Posted
Posted (edited)

There is a few GMC 1500s, not sure on your package tho.. Most with a 20x10 with a 3-3.5 lift have 33-12.50-20 or 305 55 20.  The 6 plus inche Lift most are 35-12.50.  

 

Turn the wheels and measure how much room you have, that will give you a basic measurement on how  tall/wide you wanna go. An inch taller looks like it would help you a ton. Remember an inch taller is a 1/2 inch bigger all the way around...really isn't much.

Edited by Flatblack83
  • 1 year later...
Matt1072 New Member

Matt1072

Posted
Posted

I've got the same truck just different color. It's getting the 3.5 rc lift today..  what size tire did you end up going with? I've got 33/12.5 r20's to put on it but thinking I have to buy different rims. Kind of sad cause I hate to get rid of my ballistics rims.. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,759
    Total Members
    8,960
    Most Online
    DM22
    Newest Member
    DM22
    Joined

  • Who's Online   2 Members, 0 Anonymous, 2,867 Guests (See full list)

  • Latest Articles

  • Posts

    • B14Sierra
      Cam chain tensioner question

      By B14Sierra · Posted

      So I'm in the middle of a DOD AFM delete on my 6.2 L86 Sierra. I had a pick holding the tensioner but after I got the Cam phaser gear off I was cleaning off all the rtv and apparently I didn't have the pick seated far enough in. I bumped it and the tensioner sprang forward.  I think everything is good but I want a second opinion. The top of the tensioner is just a looped piece of plastic that rides in that channel right? There is no spring or anything is there? I got the gear and chain back on and it seems tight and everything looks right. I'm hoping nothing fell out.
    • dna9656
      No low range 4 x 4

      By dna9656 · Posted

      My 2015 1500 LTZ Silverado suddenly won't go into 4 x 4 low. It will go into 4 x 4 high.
    • asilverblazer
      Transmission Woes :-(

      By asilverblazer · Posted

      Yep, just a quick reference point.    My main point being I’d do a thousand other things before I’d pay 10k for a transmission.    Speaking in ignorance cause I don’t look at these trucks, what is it worth? 20k?
    • asilverblazer
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By asilverblazer · Posted

      I think users are going to want to pick their monitored parameters, which parameters they want to see first.    It should probably start with baseline at a minimum and adjust to learned, but be able to overlay baseline for comparison.   A simple severity level would be able to determine what type of alerting is appropriate or user selectable.    Why not use the OBD port though?   I think a phone connection would be a good idea, push notifications type deal.   Number 1 issue is having data is useless if you don’t know what the data should be under normal conditions. 
    • Chuck FB
      summer road trips in the 2026 2500HD

      By Chuck FB · Posted

      I thought I would use your thread and add to it as I just did my first longer drive with my truck in the last couple of days. I drove from the Grande Prairie area of Alberta down to Edmonton and most of where I drove in the city was the ring road so fairly free flowing but a bit of stop and go as well in the city. Stayed the night and returned home and not too many stops along the way each way but every restart and certainly every cold start sets it back for fuel mileage. Why I say that is I see some people will cherry pick a fuel mileage leg after the vehicle had been warmed up driveline wise before hand and its a forgiving ( easy rolling drive leg for example ) and call that their fuel mileage which can give a false perception of reality. I was not heavily loaded at all but never the less the flip bak cover, rubber bed mat, various tools etc and extra jerry cans of fuel all way up to a few hundred pounds of dead weight so its not an empty truck. The cold inflation tire pressures are set more near the freezing point so once they are warmed up driving I was showing 45 front and over 40 rear and realize high inflation pressures would help a little in fuel mileage but certainly not the ride on our crap sections of highway. The weather was good so was not raining as that can really drag mileage down, in fact I had a bit of a tail wind on average driving home. Most people on here would never have driven on that freeway to visualize it but its got a fair bit of rolling type of landscape with numerous river valleys. For the most part I had it on cruise set to 62 although kicking it off if I caught it in time before it started down shifting and self braking going down the grades. Most of the more substantial grades its shifting into 7th I believe as 8th just doesn't have it. Total distance round trip was 643 miles and my overall average and I did refuel three times in all, figured out to 17.65 miles per US gallon. My best fuel mileage section refuel within all of this figured out to 18.46 and these are all hand calculated figures. I find if anything that the trucks computer can be over optimistic, sometimes its pretty close but other times its stretching it. On paper persay in theory the truck would have just about made it on fumes for that whole drive without refueling once.    Which made me think of the topic thread of the wonder if these trucks could do 20 mpg and that is a good question, certainly would have to be on an easy going flat highway, no head wind, the right temperature, not packing around a bunch of dead weight and puttering along even slower than I was I would suspect and going steady and not stopping to smell the flowers or take a piss !. It probably is possible but not without effort to attain that with the wind resistance and weight of these trucks. Of course on my drive most people are passing me if they have the power as per loaded highway tractors, never mind a lot of speedy vehicles but the speed limit is 68 and most are at or well over that. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...