Jump to content

High output alternator belt size

kickass audio
 Share

Recommended Posts

kickass audio Enthusiast

kickass audio

Posted
Posted

Since I wasted $160 in belts today as nobody had posted this anywhere online, I figured I would hopefully stop someone from blowing money and help them get something that fits.

 

I just replaced the factory alternator on my 2014 silverado 1500 today with a 370A mechman elite alternator. Since that alternator is high output it has a smaller pulley installed than the factory pulley. The OE alternator has a 2.5" pulley and the new Mechman alternator has a 2" pulley (that's their standard size for nearly all alternators). With the .5" difference in size you must get a smaller drive belt for the alternator, water pump and harmonic balancer or you will make the belt slip. In my case, the 72" factory length belt was right at the outermost limit of the tensioner so it definitely wouldn't work out.

 

I found that you will need to get a 71-1/4" outer circumference belt for the engine. In my case, NAPA didn't have the belt length in a 5 rib belt combination, they only had it in a 7 rib belt. I just used a utility knife to cut off 2 of the ribs and it works fine (plenty of other people I know do this and it's totally fine). The part number for this belt is through Gates as their fleet runner line under 080708HD, napa has it listed on their inventory as NBH 25-080708HD.

 

I hope this helps save someone else the hassle of cutting belts just to find they are too short. I will warn you, for this belt when it still had the 2 extra ribs on them, it wouldn't fit due to the extra deflection of the belt hanging off the lips on the pulleys, that made me worry as my two other belts were the same and even when I trimmed them it wouldn't fit.

 

Another word of caution, since you are getting an alternator with a half inch smaller pulley you will spin the alternator faster than the OE alt. Because of this I would not recommend you rev the engine up higher than 4700RPM. Going faster than that will over rev the alternator and can make it die (I did this in the past on my 2004 Envoy when I would floor it to get up to speed on the thruway and it would spin up really fast). The factory pulley size of 2.5" can handle you revving the engine up to 6000 RPM before risk of blowing up the alternator. Also you can NOT take the pulley from the OE alternator and stick it on the mechman alternator. The factory alt uses a centrifugal pulley that has grease inside (hence the black cap on the face of the pulley), I tried to remove that cap thinking it was a dust cover for the nut but it popped a bit of grease out in my face when I pried it off.

  • 8 months later...
Rockdigga New Member

Rockdigga

Posted
Posted

Should be a 6 rib 13/16" on your truck...I believe. I'm having same issue with my new high output alternator and finding a serpentine belt for a 14 silverado but I need one about 70 in 6 rib 13/16" 

  • 2 weeks later...
WashMan03 New Member

WashMan03

Posted
Posted
On 2/6/2021 at 9:40 PM, Rockdigga said:

Should be a 6 rib 13/16" on your truck...I believe. I'm having same issue with my new high output alternator and finding a serpentine belt for a 14 silverado but I need one about 70 in 6 rib 13/16" 

What belt did you end up going with?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   
    • devonthegreat
      anyone interested in a 2002 Chevy Silverado 4x4 parts truck NYC

      By devonthegreat · Posted

      **SOLD** Please end or delete post. thank you
    • PBNB
      Tire pressure for 37s

      By PBNB · Posted

      Do you think this width might affect the chalk test with a higher pressure closer to 65psi? I think lowering the pressure makes sense to get the tread to lay flatter

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...