Jump to content

2020 3.0 Duramax Winterizing Questions

TheRealZatarra
 Share

Recommended Posts

TheRealZatarra Enthusiast

TheRealZatarra

Posted
Posted

Firstly, my truck is the 2020 Silverado RST 3.0 Duramax.  I live in remote interior Alaska and we need to do a bit more Winterization here than just a block-heater.  Last year we had a couple separate weeks of -50 to -64! degrees here.  Typically we do an oil pan, block heater, transmission, battery heater pad (or trickle charger) and use an electrical outlet splitter to connect all of those back to the plug which hangs off the front.  Now, I have searched far and wide for some engine diagram to show me where the block heater is on the LM2 3.0 Duramax but I cannot find it anywhere.  Man I miss having Chiltons/Haynes manuals available but I guess those are becoming things of the past.  I have climbed under it and started following the wire bundle from the from bumper backwards, but lost it in those tight spaces on the drivers side.   I'm guessing the block heater is on the driver side but I cannot find it.  I'd like to combine the power plugs somewhere back near the block heater so that I do not have to run heater pad cables so far back and under to the transmission, oil, etc.

 

I'm also half tempted to bypass the GM power cord, which apparently won't conduct until -18 degrees because "you don't need it".  Well, that doesn't make good sense.  #1 that thermistor which blocks current is very likely to fail at some point, cutting off ALL of my engine,trans,oil pan and battery heat which would be QUITE inconvenient.  Secondly, error codes or no, I disagree with the idea that you don't need to plug it in at -15 degrees.  If you run your engine, get it hot and then park it and let it go back to -15 and then run it hot again (repeat,repeat) you will build condensation in all those parts... which is another reason to plug these things in during continuous cold weather.   I could run a completely separate electrical splitter and have *another* cord hanging out the front, but sigh, this is a NEW truck and I'd kinda like to avoid that.

 

I've also been looking for a front end bra of some type, to help block some of that -50 degree air from cooling down my engine compartment (up here that really does help) but I'll be damned if I can find one anywhere for the 2020 Silverado RST.  If you know of one please help me with a link?

 

Lastly I've had a funny quirk happen to me twice on this truck.  I go to start it, press the ignition button and rat-tat-tat-tat-tat-tat-tat-tat is unstoppable for about 45-secs to 1 min.   It's weird, but then it stops, I hold my breath, press ignition again and it has always started up without a problem but that's weird.  Anyone else had this happen?

 

Thanks in advance for any helpful advice.

 

 

 

 

BurnsMax Enthusiast

BurnsMax

Posted
Posted

I'll see if I can find a diagram.  The heater works when plugged in, but it isn't recommended until below 0F cause it can cause issues where it turns on the fans full speed all the time(I believe there is a tsb fix for this).  You don't need a bra because your shutters will stay closed to keep the engine hot.  They will open and close to keep your engine at optimal operating temperature.  When does your truck act like that when start? Cold or warm temps.  May want to drain the water out of the fuel filter

TheRealZatarra Enthusiast

TheRealZatarra

Posted
  • Author
Posted

Thanks for feedback.

My engine has never done the stuttering start thing in cold weather, only warm weather.  I'm certain there is no water in the fuel.  I even drained it.  I'm willing to bet it's a software bug, because after the 45 secs of attempting to start, it starts no problem next attempt without exception.

 

BurnsMax Enthusiast

BurnsMax

Posted
Posted

You're welcome.  Try the other FOB and make sure there isn't an issue with that one.  Mine starts instantly.  May need to bring it in to see what is going on

TheRealZatarra Enthusiast

TheRealZatarra

Posted
  • Author
Posted
22 hours ago, BurnsMax said:

You don't need a bra because your shutters will stay closed to keep the engine hot.  They will open and close to keep your engine at optimal operating temperature.

I don't know what you mean by shutters.  Looking right through my front grille I can directly see the radiator with no visible vents or flaps.   What closes?    See attached picture o took looking straight back to the radiator.

20200726_105246.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Lower trims ( WT, Custom, Silverado ( aka LT )

      By newdude · Posted

      HD at the moment, are kinda their own deal.  How LTZ sells on those vs on 1500, there is a difference.   They are merging most of the mid trims on 1500.  LT, RST and LTZ are replaced by one trim, Silverado.  LT and RST are a BIG portion of sales.    Bad naming choice aside, the new Silverado trim will offer the spread of options that those three trims offered.  So expect to see things like the tech package for example, and memory seats.  And LT Trail Boss will now just be "Trail Boss" (formerly LT Trail Boss) but will offer content spread like the new Silverado trim will.  The press photos showed the Trail Boss (formerly LT Trail Boss) has access to Super Cruise now, which on the current truck was High Country only.       Here is the Trail Boss interior.  Memory seats and Super Cruise are present.  All things the LT Trail Boss it replaces, and the RST it was based on didn't get on the current gen.  You had to go to LTZ or ZR2 for memory seats, and High Country for Super Cruise.      
    • dennismc
      2021 vs 2026 handling (1500 X31 Sierra)

      By dennismc · Posted

      I installed a Hellwig rear sway bar on my 21 Sierra SLT, it made a huge difference on how the truck handles, no body roll, the trucks much more planted now. Not sure of the suspension differences between the 21 and 26,  if its body roll your having a sway bar will solve it. 
    • Old Bay
      frustrating P0446 code

      By Old Bay · Posted

      So a follow up and my fix. I found in online searches the live data to look at on a scan tool to verify the fuel tank pressure sensor was working.  It showed an spec number towards the lower end of the rang, but in spec.  Then while it was running opened the gas cap and the pressure should change.  It didn't change even a tiny bit.  The data for the purge valve said it was open...never changed. So then I measured the voltages on the plug for the fuel pressure sensor and they matched what it should be.  So local car quest parts had the sensor in stock...it was a bit of a pain to remove and an even bigger one to get it to actually go back in.  It helped to unbolt the driveshaft and bungie cord away from the gas tank to give a bit more room to work. So fuel tank pressure sensor in I cleared the code, and started it up.  I went to the scan tool's live data and... Eureka! The pressure number was different and fluctuated a bit.  So took it on a short drive and pressure number varied saw the purge valve go from closed to open and back to closed.  Drove it to and from work for roughly a week plugged in the scan tool no codes.  I took it in to get tested and passed.  In my state's infinite wisdom (oops meant greed), since I pushed the test with the maximum extensions I have to take it back in by Feb '27 to 'get it back up to date', then my next test won't be until Feb '29. 
    • newdude
      loose lug nuts

      By newdude · Posted

      Any grease on the stud threads of any kind?   Wheel studs should have NOTHING on them for proper torquing and so the nuts don't back off.     Are all of the mating surfaces clean?  So wheel, rotor and hub?     We've had plenty of trucks at work with that wheel, this is a first to me.  Makes me think they've got a lube tech putting anti-seize on all the wheel studs or some kind of grease, and they need to stop doing that.  To have 11 other trucks with the same exact problem.      
    • Flynlow
      2027 Chevrolet Silverado: Official Discussion

      By Flynlow · Posted

      I was a Chevy guy for years, then switched to GMC because I liked the looks better.  I'm actually thinking I like the Chevy looks better than GMC for the first time in a lot of years.   One thing I know for certain, the new GMC dash is hideous!  Chevy wins this one!  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...