Jump to content

Stabilizer Sway Bar Link

Tmoney22
 Share

Recommended Posts

Tmoney22 Enthusiast

Tmoney22

Posted
Posted

Hello, I just installed the rough country 2 inch leveling kit and I was wondering if anyone knew the proper way of tightening the sway bar link? Also the torque specs for the strut bolts and bolt on the upper control arm that connects to the knuckle?

Gangly Senior Enthusiast

Gangly

Posted
Posted

For the sway bar link you have to hold the bolt stationary while you thread the nut down to the base of the bolt.  Once the threaded nut reaches the base of the bolt, you can tighten it down to its specified torque spec without having to hold the bolt as well.

 

Torque Specs for the Upper Control Arm Ball Joint

First:  26 ft/lbs

Second:  Additional 60-75 degrees (A little shy of a 1/4 turn of a wrench)

 

Strut Bolts

Upper:  43 ft/lbs

Lower:  37 ft/lbs

  • 3 years later...
23RST Enthusiast

23RST

Posted
Posted
On 8/4/2020 at 5:05 PM, Gangly said:

For the sway bar link you have to hold the bolt stationary while you thread the nut down to the base of the bolt.  Once the threaded nut reaches the base of the bolt, you can tighten it down to its specified torque spec without having to hold the bolt as well.

 

Torque Specs for the Upper Control Arm Ball Joint

First:  26 ft/lbs

Second:  Additional 60-75 degrees (A little shy of a 1/4 turn of a wrench)

 

Strut Bolts

Upper:  43 ft/lbs

Lower:  37 ft/lbs

when you strut bolts, do you mean the bottom T-bar torque to be 37ft lbs? I installed Bilsteins not too long ago and the instructions specified 53ft lbs

  • 8 months later...
Aubie_01 Enthusiast

Aubie_01

Posted
Posted

 

On 8/4/2020 at 5:05 PM, Gangly said:

For the sway bar link you have to hold the bolt stationary while you thread the nut down to the base of the bolt.  Once the threaded nut reaches the base of the bolt, you can tighten it down to its specified torque spec without having to hold the bolt as well.

 

Torque Specs for the Upper Control Arm Ball Joint

First:  26 ft/lbs

Second:  Additional 60-75 degrees (A little shy of a 1/4 turn of a wrench)

 

Strut Bolts

Upper:  43 ft/lbs

Lower:  37 ft/lbs

 

On 8/4/2020 at 8:25 PM, Gangly said:

74 ft/lbs

 

I know this is an older thread.  These posts were incredibly helpful!

Gangly Senior Enthusiast

Gangly

Posted
Posted
On 9/22/2024 at 9:23 AM, Aubie_01 said:

 

 

 

I know this is an older thread.  These posts were incredibly helpful!

You're welcome, I'm glad you were able to use the information.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,902
    Total Members
    8,960
    Most Online
    whenindoubtuseahammer
    Newest Member
    whenindoubtuseahammer
    Joined

  • Who's Online   2 Members, 0 Anonymous, 353 Guests (See full list)

  • Latest Articles

  • Posts

    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      In the 80's 90's I'd run Honda's 7,500 miles between changes using Red Line HP 5W20 and do it for hundreds of thousands of miles with issues. Back in the day it was an SAE 20 with the HTHS of a SAE 30 and SN add load. It was also very polar. Oxidation VOA was over 120. Besides those motors were SPFI and lean burn tech. I could have likely run it longer but never did.    We had a Toyota bought new I ran on Pennzoil's latest and greatest synthetic of the day with "Penthane". A made up word for a very low dose of PAO. Tried 7,500 mile OCI's in that Group III/VI chemistry and the rings tapped out at 90K. Rocker box wasn't as bad as the one Punch put up but it wasn't good either. Also a SPFI motor.    I'm around 3,750 across the board on these GDI monsters and the oil it tapped out by then usually on TBN/TAN crossover and color. Red Line HP Euro.    The AMSOIL SS brochures tell you to follow the OEM values for the service class but that it can be run up to 25K if monitored. I can't imagine what motor could go that distance and not tap out. I've never owned one.    Yes, I know. Lot's of people do. I'm just not going to be one of them. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I knew a guy in the early 80's that bought a new Monte Carlo and ran it a 100,000 miles without ever changing the filter or the oil. Just kept adding. It looked like that inside.     
    • whenindoubtuseahammer
      My First Project and GMC has me stumped

      By whenindoubtuseahammer · Posted

      Good evening. I was lucky enough to get passed down to me a 2007 GMC LBZ that was my great uncle's. While the underside and rockers are more or less gone I feel like with time I can restore it to working order since it only has 110,000 miles and he put nearly every option he could get without getting the new body style since he did not trust DEF. So far I have done everything I can think of but when I put the key into the ignition nothing happens. I put 2 brand new batteries in it. Cleaned the terminals. Check all the fuses and relays and they all pass with my multimeter. I know I'm missing something that I just cant think of. The only odd thing is the OBD2 port works which makes me think its not the mega fuse. Any advice would be greatly appreciated. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...