Jump to content

2013 Silverado LTZ 5.3 (LC-9) leaking oil from head gasket? Is that possible?

Mrjack55
 Share

Recommended Posts

Mrjack55 Enthusiast

Mrjack55

Posted
Posted

The whole drivers side of the engine block is wet front to back with oil, but it's all lower (under the exhaust manifold).  The valve cover gaskets are fine.

Truck has 160000 miles on it, so yes it's been well driven, but how does the head gasket leak oil and no coolant?

According to the shop I took it to, they said the UV dye showed it coming from the head gasket.  Is the front cover gasket or front crank seal a more likely source?

They quoted me $3K, which seems like a lot for head gaskets.  I know it's about 12hrs worth of work, but $3K?  I'm not bashing the shop, as I understand the labor.  I just don't have $3K.

Has anyone else had anything like this?  Am I way off the mark thinking this could be something else, and not as expensive to repair? 

Thanks in advance for all help/advice.  Sorry for the rant.  This one has me fired up.

dna9656 Enthusiast

dna9656

Posted
Posted

Heads on Chevys used to leak oil from where the valve cover and the head met, engine oil would collect there and eventually soak any gasket you could install; you have to tighten the valve cover gasket exactly to spec (nobody looked this up) for it not to leak. This is why (since 1986 I believe) the valve covers were held in place by bolts in the center of the cover thus eliminating crush points under the bolts that were on the edge of the head that caused the leak between the cover bolts. I do not know when Chevy went to the style I have on my 06 5.3 but the seal (a very fancy kind of O ring doesn't leak as it's no where near the oil.

If the oil isn't leaking from the removable cover I think you must have a crack right under the cover's home. I think you could get that welded up if you can get it oil free. I've never seen or heard of an leak oil from the head gasket area, it's always been coolant.

swathdiver Senior Enthusiast

swathdiver

Posted
Posted
11 hours ago, Mrjack55 said:

The whole drivers side of the engine block is wet front to back with oil, but it's all lower (under the exhaust manifold).  The valve cover gaskets are fine.

Truck has 160000 miles on it, so yes it's been well driven, but how does the head gasket leak oil and no coolant?

According to the shop I took it to, they said the UV dye showed it coming from the head gasket.  Is the front cover gasket or front crank seal a more likely source?

They quoted me $3K, which seems like a lot for head gaskets.  I know it's about 12hrs worth of work, but $3K?  I'm not bashing the shop, as I understand the labor.  I just don't have $3K.

Has anyone else had anything like this?  Am I way off the mark thinking this could be something else, and not as expensive to repair? 

Thanks in advance for all help/advice.  Sorry for the rant.  This one has me fired up.

 

Uhh, I call BS on the shop.  Does your truck have the external engine oil cooler?  Even if it does not, the block off plate can also leak.  Weeping or leaking power steering lines can also spray oil on the block under the manifolds.

 

Best I can tell, oil comes up through the cam bearings to the lifters and up through the pushrods and drains back down.  Down through where, then?  I would think that if the head gasket was compromised and leaking oil, your motor would not be running, at least for long.

 

2013 Chevy Silverado 5.3L Engine Oil Schematic | Auto ...

  • 5 months later...
Oilyone Enthusiast

Oilyone

Posted
Posted

OK Mrjack, don't keep us all in suspense. Where was your oil leak? My 2012 5.3 with 60K miles has developed an oil leak from somewhere near the back driver side. Oil shows up down below on the side of the engine and bell housing. Oil even drips down on the transfer case prop shaft. Had it in to the dealer yesterday and they couldn't spot the leak so put dye in the oil and want me back in 1000 miles or so. They mentioned the head gasket but I don't think that's possible. Maybe cam cover gasket, oil pressure sensor or valve timing sensor? My torque converter and flywheel and oil filter are dry. Here are some photos.

IMG_6019.JPG

IMG_6022.JPG

IMG_6023.JPG

IMG_6048.JPG

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,782
    Total Members
    8,960
    Most Online
    ShowMeShooter1332
    Newest Member
    ShowMeShooter1332
    Joined

  • Who's Online   1 Member, 0 Anonymous, 6,945 Guests (See full list)

  • Latest Articles

  • Posts

    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      I was around and remember that era very well, so I'm calling b/s on that statement. If they were that bad no police department or taxi company would've bought a single one ... but they were used in both services (and fire) for DECADES. They were bulletproof and proven. Even the early 21st century ones weren't too bad! The early models were legendary.   Mine is proof, but people like atlas are blinded by agenda and refuse to believe facts right before their very eyes.   Even decades after they were built, a new generation started driving them, posting all their builds and shenanigans on Grandmarq.net and Crownvic.net. The failures would show up then, since they all were deep past 100k-150k miles by that point, and younger drivers tend to be a little aggressive, especially with vehicles than can lay a one-tire fire for as long as you hold your foot in it. They've more than proven themselves over the decades.   The only thing that'll really take them out is road salt. The bodies and sheet metal were garbage. A victim of the cheapout FoMoCo and GM have been partaking in before then, and since.   Today it's the stuff that counts - the undercarriage that rots away first!    GMs Caprice was no slouch either. Reliable as a stone ax - the opposite of what they build now.    
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      Let me know how your vehicles do in 10 years. You don't know ******, kid. 😂    There's a reason that Panther platform was used as police, fire, and taxi service for DECADES ... long before you were born, apparently.
    • davester
      Disconnecting Battery

      By davester · Posted

      If your connector also has a big lever to get the connector on and off, you don't want to force the lever either way, as it becomes a bigger problem if you bust the lever or the mechanism it works.
    • davester
      Disconnecting Battery

      By davester · Posted

      It's just useful to disconnect the battery to prevent odd shorting out when unplugging/plugging stuff together.  I also  touch the two cable ends together (after disonnecting) to drain the small amount of stored battery energy in various modules.   I believe the main system where you need to be more concerned with, so you need to do the above and then wait some time, iss when you are working on the air bag system, to prevent inadvertent firing of the air bags.   The in-cab switches are just that, plain switches, it's generally not a problem to swap them in/out.  For my '12, I'll get an error message on the dash if I power up the truck w them unplugged, but that's it (power up= turn the ignition on).   The ITBC located above the spare tire is a computer that manages the trailer brake system.  That is probably more important to have the battery disconnected.  It does have to be programmed to the truck, either before or after it's installed, for it to work.  For my '12, I had a very hard time reinstalling the main connector to it (IDK if yours is the same or not), it turned out the silicon seal was jamming up, preventing it from going on all the way.  I finally got it fully installed by lubing the seal with a bit of dielectric grease, then it slid on and latched in place easily.
    • BCGM
      Remote Start Noise 2024 2500 HD Gas

      By BCGM · Posted

      JR ! I just got the truck back from the Dealership today . The technician did a cold remote start on the truck this morning and it made the noise . It was determined that it was a starter issue and replaced it under warranty . Of course   it did not make the sound after a new starter was put in because the truck was not cold . We will we see what happens tomorrow morning when I start the truck cold  . Keep tuned !   Oh I found a video on YouTube of a cold start and it did the same thing your truck and mine do , I will see if I can find it and post it up

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...