Jump to content

New 4" Lift And Tires Question?

Sean Glasco

By Sean Glasco
in Modifications & Accessories

 Share

Recommended Posts

Sean Glasco New Member

Sean Glasco

Posted
Posted

So I just ordered the Readylift 4"SST lift and Nitto 33"x12.5 Ridge Grapplers. This is going on a 2018 1500 4x4custom. I plan on using the OEM wheels until I can save up for aftermarket. Will it work if I use a 1/2" spacer until then? I don't know what the offset is on the OEM wheels. I went to Readylift's site and looked at the tire fitment tab. This is what it says:

 

33" Maximum tire diameter

33x11.50 for no rub on a 9" wide wheel with +6 offset

18" - 295/65R18

20" - 285/60R20

22" - 285/50R22

When lifting a vehicle and installing aftermarket wheels and tires, a tire manufacturer's construction and material quality can alter vehicle ride quality. When increasing a vehicle wheel and tire size, most larger aftermarket truck and SUV tires are 8-ply (or more) E tires compared to typical OEM 6-ply C tires. This more rigid sidewall construction increases the perception of suspension stiffness often described as ride harshness. The ride, handling, traction, noise, fuel economy, and wear differences between All-Season, All-Terrain, Mud-Terrain, or Trail-Terrain type tires can be significant. Please take into account tire and wheel choice will generally have a meaningful impact on the ride & handling experience.

M1ck3y Senior Enthusiast

M1ck3y

Posted
Posted (edited)

The problem isn't your wheels, its your tires that are in question. Which measure 12.5" on a 10 inch rim. Ready lift says a tire that 11.5" wide on a 9" wide rim (with their wheel spacer) clears.

 

I think your tires width and diameter will end up being larger then spec. Tire width shrinks a little bit going on a smaller rim, but.. all that extra width has to go somewhere so I would think diameter would increase? Really you need to put it on to find out, or find someone else who has tried this exact setup. 

 

Most likely your stock wheels have offset around +18 - +24. It would help if you listed what wheel it is.

 

*edit*

 

Wow, they don't recommend you use 4hi. Did you see that?

Edited by M1ck3y
Sean Glasco New Member

Sean Glasco

Posted
  • Author
Posted
15 minutes ago, M1ck3y said:

The problem isn't your wheels, its your tires that are in question. Which measure 12.5" on a 10 inch rim. Ready lift says a tire that 11.5" wide on a 9" wide rim (with their wheel spacer) clears.

 

I think your tires width and diameter will end up being larger then spec. Tire width shrinks a little bit going on a smaller rim, but.. all that extra width has to go somewhere so I would think diameter would increase? Really you need to put it on to find out, or find someone else who has tried this exact setup. 

 

Most likely your stock wheels have backspacing around +18 - +24. It would help if you listed what wheel it is.

I just know its a 20" wheel. How do I find out the width?

MikeBMW Senior Enthusiast

MikeBMW

Posted
Posted (edited)
21 hours ago, M1ck3y said:

Google. 9" wide +27 offset. I don't see backspacing there, but you'll find it through google.

 

https://www.wheel-size.com/size/chevrolet/silverado/2018/

This is my go-to for factory wheel off sets:
https://performancelifts.com/wheel-back-space-information.html

Edited by MikeBMW
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      286,740 Mile Services   8/6/2026   New AC Compressor. Refrigerant oil and dye, evacuate and charge system.  New exhaust system from cat back.  New Iridium plugs plus replace #3 coil Repair/rewire headlamp wiring (passenger side) and replace all forward bulbs. Polish lenses of both assemblies.  Pull rear rotors, clean and adjust parking assembly. Inspect, clean and grease front calipers. Check pads and shoes.  4 wheel power bleed of brake system. Dot 4 Reset idle speed 50 rpm higher New Serpentine belt.    Will need new pads in the rear in about 5K more miles.    Tax Title and License out the door just short of a grand.    AC clutch had bitten the dust. 1 year warranty on the pick and save replacement. Thing will make a Polar Bear cry Uncle.  He spent quite some time on the wiring. It was in the harness and he does nothing half. I got off cheap. I have considerable more light down the road. Sylvania Silver Star replacements.  Gas seal between the porcelain and shell of plug #3 was blown, cooked the coil. That was the cold miss.  Love the new exhaust. I can sneak into the neighborhood again.  Nice to have a working parking brake again. Belle Tire never got it done. That was disappointing.    This was one of her bigger bills and still way cheaper than a payment even given the oil consumption. This thing cost me under a hundred a month in repairs and normal routine costs. What is my incentive to replace it? 🤔           
    • AidenVorpagel
      cam upgrade in CA

      By AidenVorpagel · Posted

      hello I recently bought a 2012 gmc 1500 with a 5.3 and have a AFM disabler on it I'm interested in doing a cam but I'm worried if I remove the AFM system I will fail smog does anyone have info if they are able to detect that or a work around to it (not talking about hot smogging) please let me know thank you  
    • B14Sierra
      Noise after AFM delete

      By B14Sierra · Posted

      Did you figure it out?
    • B14Sierra
      Possible lifter tick after DOD delete

      By B14Sierra · Posted

      Update. I started chasing down my symptoms. Started first with pulling valve covers and looked at everything. Everything looked good and couldn't hear or feel anything different. Then a compression test. 240 psi or really close on each cylinder. I was worried I was a tooth off of timing. Not bad for an engine with 173,000. Granted I did put new heads on. I sprayed water around the injector area to see if I could hear a change. Nothing. I hooked up my new hp tuner which I should have done in the first place but I don't really know what I'm looking at just yet but am learning. I noticed the fuel trims were way off so that told me I have to have either a bad injector or exhaust leak. New injectors, so I did the shop vac on blower and in the tail pipe. Sprayed soapy water and found the exhaust flange on the drivers side was leaking. I didn't think it would be that considereding I pulled the heads and left the manifolds attached. I did have the transmission replaced not long ago. They must have not seated them properly but I guess I didn't notice. I put in new gaskets on both sides. Which by the way isn't a bad job but I had a hard time getting them to seal right. Took two attempts. Reset the fuel trims and the ticking is gone, engine runs smooth and acceleration has improved. Got to feel the real difference with that stage 1 cam. It's not that big of a difference but it does add a little more. It feels like how the truck should have been from the factory.
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Can it still be Assembled I?    Stribeck says that we need a certain amount of viscosity under conditions of load and velocity to prevent two surfaces of a know roughness from tearing each other asunder. And we have marketing trying to tell the masses that those two surfaced require less of that commodity due to more exact limits being placed on the same old clearances. We also know that there are limits to how hard something can before it becomes to brittle to be viable and to smooth to 'wet' the surface and that both of those conditions have been known and met since about the Second World War.    That viscosity value shook out at 10 centistokes at 212 F just under a hundred years ago.  Give this a look: [Anton Parr]     What is advertised is the Kinematic viscosity (mm2/s) or that which has been density adjusted but the value we are after is the dynamic viscosity (mPa.s) or true viscosity. You can see that this number is dependent on density thus base stock and temperature. You can also see that an SAE 30 doesn't reach that value in this example. However an SAE 30 that is at the upper end of the SAE 30 range; 12.5 cSt (mm2/s), might. 12.5 * .83 = 10.375 (mm2/s). If you could find an SAE 30 at the upper end these days.   Then there is the complication of viscosity modifiers or VII or VM, whatever you wish to call them. Polymers added to very thin base oils, perhaps 3 to 6 cP oils, that will meet the SAE *W30 spec at 'tested' shear rates and 100 C/212F  target temperature. So a polymer fortified base that is a fraction of the 10 cP requirement Stribeck insist upon.   This could be all well and good if those polymers didn't have two very problematic 'features'. They shear or loose viscosity both 1.) permanently and 2.) temporality. And they do both omitted in the advertised data with the distinct  purpose of deceiving the consumer of the actual operating state of the fluid. I've shown the example of Warren Oils COSTCO 10.91 cSt 5W30 formuation several times where the 100 C HTHS value is 6.9 cP!! That's the temporary shear down and with and SSI or shear stability index of 9.4 cSt. Note the intentional deception in using mixed units?    After a short while that 9.4 cSt oil has a viscosity corrected dynamic value of 7.8 cP. But as the SSI is still within the range of an SAE *W30 whose lower value is 9.3 cSt.    This allows them to continue to call this SAE 16 weight oil a 30 weight, the cake, and still meet the API requirements for fuel efficiency IMPROVEMENT mandated by the EPA. The eating of the cake. By the time you've worn out your motor doing the responsible thing by adhering to the warranty requirements, (the stick), you get deprived of the carrot, wear control. So sad, to bad.   So what can be done? Do I need actually say? [Anton Parr]       Even this must be monitored if the oil is on the low side and the VII an organic or you opt for a 0W40 with an even lighter base oil and more / higher MW VII. (Note the lower density of the 40 weight versus the SAE 30 mono-weight?)    There is another workaround. Temperature. An SAE *W30 run at a bulk temperature of between 180 and 195 F.    Being the belt and suspenders sort I am I do both. Run it cook and run it heavy.    In Part II I'll work the AW package. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...