Jump to content

Does the spare tire have to be the same size (height) as the tires on the truck when using the spare?

BlueMax 23

By BlueMax 23
in Troubleshooting & Recalls

 Share

Recommended Posts

BlueMax 23 New Member

BlueMax 23

Posted
Posted

I had a flat on the drivers side, front tire this week-end. I pulled the spare and saw it was a 17 rather than a 20 inch tireI thought it would be okay and with some reservation I mounted it and headed home.  
 

About 15 miles into a 20 mile trip home in the dark I realized there was smoke boiling out from the undercarriage.  

 

Long story short, the differential is now toast and has to be rebuilt.  
 

The question is - is this because of using the smaller spare tire or was it just a coincidence? 

madweazl Enthusiast

madweazl

Posted
Posted (edited)

The wheel size (17" or 20" as you referenced) isn't important (provided it clears the brake package). What is important is the tire size (specifically diameter). Our '24 has 275/65r20 (34.1") with a spare measuring 275/70/r18 (33.2") for a difference in diameter of roughly 3%. I wouldn't expect that to have a detrimental impact to the LSD but I'm sure the further it's driven the hotter it gets. 

Edited by madweazl
newdude Senior Enthusiast

newdude

Posted
Posted
2 hours ago, BlueMax 23 said:

I had a flat on the drivers side, front tire this week-end. I pulled the spare and saw it was a 17 rather than a 20 inch tireI thought it would be okay and with some reservation I mounted it and headed home.  
 

About 15 miles into a 20 mile trip home in the dark I realized there was smoke boiling out from the undercarriage.  

 

Long story short, the differential is now toast and has to be rebuilt.  
 

The question is - is this because of using the smaller spare tire or was it just a coincidence? 

 

 

The spare tire on trucks with 18" and 20" wheels on the 2015-2019 trucks is, from the factory, an 18 inch wheel with LT265/70R18 tire on it.  Its the same tire that is on 18" wheels from the factory, and is of the same diameter or within 1/10 of an inch of the stock 20" tire, LT265/60R20.

 

If you've got a 17" spare, someone swapped it out at some point.  The 17" spare is only on trucks with 17" wheels.  You need the 18" spare wheel and tire size LT265/70R18.

  • 3 weeks later...
cfell Enthusiast

cfell

Posted
Posted

You “can” if it meets tow rating… but the computer will not be happy.. don’t drive over 45 until you repair properly 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Well....I've done my first intake gasket. Probably wrong, but...we'll see?   Ultra black on the china walls and 1/4" up onto the sides of the intake gaskets. Permatex High Tack (couldn't find Gaskachinch) on the head side of the intake gasket. I read wrong and it says you're supposed to put it on the mating surface of the head, not the gasket. Hoping it's like a PB&J sandwich where it doesn't matter what side the PB goes on so long as there's jelly. That crap is messy/sticky and I got a dab or two on the intake port openings, tried to wipe it off. Hopefully it won't be a big deal and will only aid in sealing.   Per instructions I left the intake (top side) of the gasket dry except for a light smear of RTV around the coolant ports. Wiggling the intake in there was a bear but I had help to free me of surrounding wiring/stuff but I was basically able to set it straight down lined up with the bolt holes.   I did not think to wait until the RTV skinned over but there probably was 5-10 minutes while it sat before installing the intake.   Bolts finger tight first. Then, followed the Chilton's manual pattern to snug them to 15 lb-ft.   Waited a little over an hour, and then did the final torque in sequence again to 35 lb-ft.   Yesterday I replaced the fuel pressure regulator and got my new "nut and bolt kit" (fuel lines) installed. Damn GM used security torx on the spider, which I don't have, so I got scammed at the local HW store for an off-brand security Torx bit set.   The new driver's door mirror arrived yesterday, so, there's a chance this thing could be running and road legal tomorrow? I don't want to get my hopes up.   This will be my first time stabbing a distributor, too. Although, lucky me, someone else marked the old distributor for removal previously, I did see that. (Someone's been here before!!). Engine is still at TDC so it *should* be just a matter of transferring the mark to the new dizzy and rotating it into place.
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      He has his dad’s newer truck he’s put away. He has several old cars he rotates between him and his family. I’ve seen a restored square body and a SS Chevy truck he’s sometimes drives. He did raffle off a new suburban recently. As much as he is watched if he drove new stuff as a rule we’d know it. It would be fine by me. I don’t care what people prefer. I got one more new one in me. I’d rather my wife get one. I can’t get her out of the Genesis. Don’t tell anyone. I want her to get an electric truck. I want to put a generator in the back. Just because. She hasn’t bit yet.
    • Atlas
      2027 GMC Sierra: Official Discussion

      By Atlas · Posted

      Yes, you must have seen my thread on the Blazer. HOT GARBAGE, but I love them anyway. I'm convinced every car guy has a soft sport for an S/T series somewheres. Probably even a Panther too, if I'm being an honest car guy. That doesn't mean they aren't junk. And they definitely don't get better with age. I sometimes play with old cars, but that's by choice. I don't rely on them and they aren't my everyday fleet.   Derek plays the common man on Youtube and that's no doubt where he started. Now he has Youtube money (and Motortrend, etc). You think his crews and his wife ride around in old beaters when they're chasing him and his wrecks across the country? No he's got newer and nicer stuff for that, you'll see glimpses of it in the footage.
    • Atlas
      2027 GMC Sierra: Official Discussion

      By Atlas · Posted

      You refuse to own anything made in this century yet you reportedly own... a 2007 Silverado, which is now almost 20 years old. The dissonance.... turn up your hearing aid?   You clearly don't understand the government contracting process, brother. We send people to die on front lines, keep the public safe, and make people's husbands, wives, children enter burning buildings with equipment from .....wait for it.....   ...the lowest bidder....   Just because something is used for a long time doesn't mean it's good. But it might be cheap and plentiful.   Please, continue to whine about new trucks in a thread dedicated to new trucks, which you've said you'll never own. We get it. Go tell everyone how you're stuck in time on a Panther forum. I mean, Jesus, an 86 isn't even one of the good Panthers.
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      It really is comical when people don’t agree or see the reason some people prefer the older vehicles. They become condescending. All the while they may be busting their knuckles on old vehicles. I have found memories of swapping out engines in my old GM cars in a weekend without much hassle. Unlike today. One wrong move a computer will shut you down. Even on something as easy as a brake job. There’s a pretty comical YouTuber called the car wizard. A garage owner who puts it all in perspective. Another Vicegrip garage that’s shows just how tough the old stuff is. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...