Jump to content

2007 SLE DIC Upgrade

tobias

Recommended Posts

tobias Senior Enthusiast

tobias

Posted
Posted

I just wanted to let everyone know that adding the Driver Information Center (DIC) to your 2007 SLE is a snap.

 

I ordered the part from gmpartsdirect.com. The install took 5 minutes.

 

Directions (I would have taken photos but it's really unnecessary as this is so simple.)

*******************************************************************************

1. Turn the truck off.

 

2. Pull the old section of dash (on the left of the wheel) off by hand.

 

3. Remove the light controls (simple plastic clips).

 

4. Remove the extra cable clipped into the piece of dash (it's already there just not being used...YET!

 

5. Install the light controls into the new piece of dash (yes it comes with the new piece of dash, new vent and the switch)

 

6. Plug the previously non used wire into the new switch.

 

7. Put the new dash plate back into place by hand.

 

8. Turn on the truck! You're done!

 

 

This mod gives you access to fuel mileage, range, gallons used, V8/V4 mode notification, tire pressures, tire sensor learning, key fob learning, chime volume, entry and exit lighting schemes, lock and unlock schemes (including automatic lock/unlock), unit and language choices, engine hours and probably more that I have forgotten already.

 

The beauty of all of this is the cost - $100.22 shipped.

 

Enjoy.

 

If you have questions, let me know!

 

Daddy. :confused:

  • Replies 663
  • Created
  • Last Reply
mini1 Enthusiast

mini1

Posted
Posted

What happens to the standard trip-odometer type basic DIC controller? Does it still work? Can you order that panel in ebony black? I'm VERY interested! I assume all the wiring is already there? I'd like to see your finnished product.

tobias Senior Enthusiast

tobias

Posted
  • Author
Posted
What happens to the standard trip-odometer type basic DIC controller? Does it still work? Can you order that panel in ebony black? I'm VERY interested! I assume all the wiring is already there? I'd like to see your finished product.

 

I honestly haven't tried to use the original button for the original information but you get all of that through the new one. You lose no functionality whatsoever. The part I linked to is black, I have the full black interior and this is an OEM part. I can send you pics of the finished install but it looks just like the one in this link:

 

http://www.automobilemag.com/features/news...a/photo_03.html

 

It's just above and to the right of the light switch and just to the right of the vent.

 

Daddy.

mini1 Enthusiast

mini1

Posted
Posted

Can you try the factory switch and see what it does? I would like to see your install. Then I can see exactly what mine would look like.

 

Thanks!

tobias Senior Enthusiast

tobias

Posted
  • Author
Posted
Can you try the factory switch and see what it does? I would like to see your install. Then I can see exactly what mine would look like.

 

Thanks!

 

The old switch toggles between the trip odometer and the regular odometer, it appears that the tranny temp has moved over to the new switch.

 

I'll try and take some pics in a few minutes and post them although it won't look any different than the link I sent before.

 

Daddy.

tobias Senior Enthusiast

tobias

Posted
  • Author
Posted

Here are the pics. As I explained, it is very simple to do this as evident by the fact that I basically just did it again in order to take these pics.

 

This is the old piece of dash.

img0472wk6.gif

 

The red arrow shows the cable that is already there now attached to the switch.

img0476xq3.gif

 

Now for the new piece with the switch installed.

img0478rt9.gif

 

There are many more screens but here's a shot of the way the display is now used.

img0483dx4.gif

 

I hope this is enough to get the point across.

 

Did I mention that the switch is also back-lit to match everything else in the truck when the lights are on?

 

Daddy

tobias Senior Enthusiast

tobias

Posted
  • Author
Posted
Is there a cheaper place to buy these? Did you have to reset the tire pressure monitor?

 

I don't mean to sound rude but I don't think I could be any more clear that the entire upgrade took 5 minutes and nothing more than what I have explained. However, just for clarification's sake, no, I did not have to reset the tire pressure sensors or anything else for that matter.

 

If you want to search for it cheaper, feel free. To the best I was able to find them, this was the cheapest option. It's $100 for something that would have cost you much more to have on your truck from the dealer.

 

Daddy.

rogerf Enthusiast

rogerf

Posted
Posted

Help me understand something. What package did you buy that has a DIC without control switches? I just ordered a truck on Monday and I don't wan't this little detail overlooked.

tobias Senior Enthusiast

tobias

Posted
  • Author
Posted
Help me understand something. What package did you buy that has a DIC without control switches? I just ordered a truck on Monday and I don't wan't this little detail overlooked.

 

I have a SLE1 3SA with some additional options.

 

It shows on the GMC site that the DIC is standard but I believe that is referring to the limited use version that only gives odometer, trip odometer and tranny temp that i had prior to this upgrade. You'll probably need to ask the dealer to be certain.

 

Daddy.

Gozer Enthusiast

Gozer

Posted
Posted
Help me understand something. What package did you buy that has a DIC without control switches? I just ordered a truck on Monday and I don't wan't this little detail overlooked.

 

If you order the preferred package on Sierra SLE1 or convenience package on LT1 you should get the full DIC with contol switches to left of steering wheel.

tobias Senior Enthusiast

tobias

Posted
  • Author
Posted
Help me understand something. What package did you buy that has a DIC without control switches? I just ordered a truck on Monday and I don't wan't this little detail overlooked.

 

If you order the preferred package on Sierra SLE1 or convenience package on LT1 you should get the full DIC with contol switches to left of steering wheel.

 

 

That makes sense, I suppose. I got the convenience package but not the preferred.

 

 

Daddy

  • 4 weeks later...
slaphappy Enthusiast

slaphappy

Posted
Posted

Wow, thanks for this post! I've been searching all over trying to find a way to add the DIC to my 2007 Silverado LT.

 

A quick question though, is the dash plate the same for both the Sierra and the Silverado? Meaning, will the part linked to work for both?

 

Thanks!

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • bluev8
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By bluev8 · Posted

      That is a fair point, and I think an OBD-first proof is probably the right next step. I agree that the value is not the hardware box by itself. The marketable part would be the software: always-on capture, baseline learning, event reduction, system-specific reports, and alerts. Also agreed that if an OBD device is always plugged in and has local storage, it should not miss the event in the same way that a scanner plugged in after the fact would. The only thing I would not want to assume yet is that an ELM327-class device gives all the late-GM data needed at the rate needed. Standard OBD live data, DTCs, freeze frame, Mode 6, VIN, and calibration information are definitely the right starting point. GDS2 also proves that a lot of useful ECM data can be viewed through the DLC without needing a DTC first. The question I need to test is whether the data needed for a useful GM V8 event report is actually available through the DLC, and at a useful sample rate: - misfire counts / roughness by cylinder - AFM/DFM state - oil pressure and oil temperature - fuel trims - voltage / reset context - U-codes and communication events - calibration / software information - whether these are standard PIDs, enhanced DIDs, Mode 6 data, GDS2-only data, or not available So I think the right benchmark is: 1. Build the OBD-only version first. 2. Keep it plugged in and logging locally. 3. Compare it against GDS2 / freeze frame / HP Tuners or another higher-end logger. 4. Measure which parameters are available and at what update rate. 5. Only justify ECM-side hardware if it captures useful evidence the OBD version cannot. So you may be right: the consumer product might simply be an always-plugged-in OBD event recorder with much better reporting. A question for you: when you say ELM327 devices can already deliver all the data needed, do you mean generic OBD Mode 01 data only, or GM enhanced data as well? For a useful GM V8 report, would generic OBD data be enough, or would you expect the tool to include enhanced items like misfire by cylinder, AFM/DFM state, oil pressure/oil temp, U-codes, and calibration information?
    • Buckwild27
      Gas Prices

      By Buckwild27 · Posted

      I agree. 
    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...