Lq4 Injectors

By s10473
November 2, 2007 in Gen III & Gen IV V8 Engines (LS-Based)

Recommended Posts

s10473

Posted November 2, 2007

I have a 03 2500Hd with the LQ4 motor. What size injectors are stock, and what are they rated up to for flow?

Thanks

Draenor

Posted November 2, 2007

Dont take it as gospel but I beleive the flow rate is 270cc/min at 26lbs

Indy

Posted November 2, 2007

Dont take it as gospel but I beleive the flow rate is 270cc/min at 26lbs

That sounds pretty funny coming from a guy from CHURCH POINT.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.3k
Total Topics

2.7m
Total Posts
Member Statistics

342,684
Total Members

8,960
Most Online

Newest Member
joshua1221
Joined 2 hours ago
Who's Online 10 Members, 0 Anonymous, 606 Guests (See full list)
- Jerry455
- BIGDOGx
- Samari21
- newdude
- Buckwild27
- hollywoodsle
- ERM
- PhilB
- chris21
- joshua1221

Latest Articles
- GM Recalls 2,700+ Trucks For Airbags That Can Explode While Parked – How To Check Your VIN
  Wednesday at 07:54 PM
- You Can Completely Disable A New Chevy Traverse By Bending The Rear Wiper Arm (No, Seriously)
  Wednesday at 05:47 PM
- Should You Use Engine Fuel Additives In Chevy or GMC? Here’s GM’s Official Statement.
  Wednesday at 02:38 PM
- We’ve Driven the Edition 1 For 4 Years. Here’s Why the Mid-Size HUMMER X Concept is Exactly What GMC Needs.
  May 29
Posts
- 2024 silverado 6.2 just went down
  
  By BIGDOGx · Posted 44 minutes ago
  
  Is this a bottom end issue, if so oil weight is not the reason or cause, i have been running 0-20 weight in my 6.2 since November of 2014 and I'm just about at 100,000 miles. Gm just released a statement yesterday stating they are bringing certain machining back in house for their next gen v-8's. I have been screaming from the rooftops on this issue since easily 2021! These lower end issues all stems from using slave wage labor in Mexico. If you were building a 60-80,000 dollar truck, would you have a guy who makes around 3-5 bucks an hour create the crank shaft for it and finish the surfaces on it? I bet 100 out of 100 people would say hell f'ing no and rightfully so! Gm tried to save penny's and in the end it is costing them millions, not to mention customers who will never look at a single GM product again after this experience!
- Electrical problem
  
  By richard wysong · Posted 50 minutes ago
  
  That GM customer service is an AI bot, don't expect a response
- Gas Prices
  
  By richard wysong · Posted 53 minutes ago
  
  Where are you located?
- Electrical problem
  
  By Rad_Rado17 · Posted 58 minutes ago
  
  You guys won't do anything. You will make him pay a $250 diagnostic fee and hopefully try and find the issue. This has been a known issue with these trucks. If GM says safety is a top priority then GM would make this a recall or some special coverage like the vacuum pump issue.
- Torsion adjustment
  
  By riddler · Posted 1 hour ago
  
  👍🏻👍🏻
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 156 members
- diesel 3.0
  
  Open Club · 279 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 212 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  KARNUT
  39
2. 2
  
  Atlas
  29
3. 3
  
  riddler
  14
4. 4
  
  Grumpy Bear
  13
5. 5
  
  diyer2
  9
Show More