Jump to content

Ignition Key Will Not Turn!

pandacom

By pandacom
in Ask A GM Technician

Recommended Posts

pandacom New Member

pandacom

Posted
Posted

2003 Z71 4x4 Unable to start vehicle unable to remove cylinder because it will not turn regardless of key being used. How can I get the cylinder out or should I just junk the column and get another. I have it torn down to the spring clip holding the cancel ring on the turn signal but cannot get the ring out holding the plate in place. Cannot get to the screws holding the housing in place without damaging the cancel cam ring. Help Plz!! If any one is out there? :lol:

bill190 Enthusiast

bill190

Posted
Posted

If you have another original key, might try that. Or have the dealer make a new key from your VIN number. Older keys wear out and stop working. (If that is the problem.)

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • mark249
      Help purchasing a touch screen digitizer

      By mark249 · Posted

      Brought my 2015 Colorado into the dealership to check my touch screen issues, had that ghost touch thing happening. They said I needed a new touch screen and they could either order me one for $500. The lady at the service deck was nice enough to tell me I could order a touch screen online for less, she did stipulate that the touch screen had to be factory OEM, you can't pair an aftermarket screen to my radio seeing it was 2015, it had to be a GM factory OEM only. I found a few on Amazon and Ebay by the numbers on the back of the old screen, DJ080PA-01A GM# 22740886, Some said "OEM" in the description and others just said "Replacement". Would a replacement be the same as a OEM as long as it had the same numbers on the back of the screen? In some of the descriptions they also show different brand names but same numbers, is that an issue?  
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      I have both but typically use the 4 legged walker (wheels on front, ski's on back).   The four wheeler is starting to be used on "longer" outdoor walks.  The 4 legged walker is particularly helpful in practicing good walking posture.  Both of my knees are at different stages of recovery and I'm trying to not develop poor habits.  I can actually manage with a cane but it's very difficult not to favor one leg over the other.  My PT recommends I continue with my 4 legged walker for a while.  Yesterday was four weeks since my last knee replacement and I'm excited about my progress to date.  It has been a hell of a rough journey so far but it is exciting to witness  systematic and continuous improvement.  I went for years watching the decline of my "mobility".  It seems that everyday now I am alerting my wife to something I can do now that I couldn't a day or two ago!  I encourage anyone facing the prospect of knee replacement to share any concerns with others who have had the surgery.  It isn't an instant fix but rather is a considerable amount of short term pain for long term gain.  Recovery time and pain levels vary for individuals post surgery but the end results are typically very positive and I've never encountered anyone regretting having had the surgery. 
    • diyer2
      AFM Disabler Question

      By diyer2 · Posted

      The lifter issue can be dealt with by shorter oil changes and quality oil IMO.
    • diyer2
      Winter Returned

      By diyer2 · Posted

      Got heavy rain, hail and light rain yesterday. 
    • Core-Lokt
      Wiring Help, Please

      By Core-Lokt · Posted

      I'm putting in an A-pillar pod/gauges, and I'm asking if anybody can identify a (preferably) fuse for a switched power and illumination circuit on the driver's side interior fuse panel. Offhand, everything I checked with a test light was constant-hot, and I'd much rather uses a piggyback fuse. I can certainly find a wire, but I'd rather not half-tap.   Thanks in advance for any help.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...