Jump to content

Running boards

bigdeer1
 Share

Recommended Posts

Pardo714 Enthusiast

Pardo714

Posted
Posted

I had a 2013 that was bought back and replaced with a 2014. I was gonna swap the 13 running boards to the 14 but was told by a tech that the mounting points were different. Don't know it this is true but assume it it because it ended up costing GM money as they replaced my running boards.

I don't think the new crew cabs are longer but they did move the b pillar forward 2 inches so there is a little more room in the rear seat. It looks like the front doors are smaller and the rears larger than on my 13 but don't know the actual specs.

lovemytruck Enthusiast

lovemytruck

Posted
Posted

My 14' CC with 6'6" box is 19" longer then a 13' CC with 5' box. It fits perfect in my 22' deep garage with room to spare. If you look under the hood, two of the cylinders are into the firewall, giving it the shorter hood length.

newdude Senior Enthusiast

newdude

Posted
Posted

If you are using the GM boards...I think the double cab 07-13 boards might line right up. Not sure on the crew or regular cab.

BringTheRain403 Senior Enthusiast

BringTheRain403

Posted
Posted

The factory boards mount to the pinch welds which in my opinion is garbage. The good boards will mount to the body mounts. I'm waiting for ICI to come out with their full stainless 4" monster step bars. Is told probably January...

 

Sent from my SCH-I535 using Tapatalk 2

 

 

mjw930 Enthusiast

mjw930

Posted
Posted

I was told by Steelcraft the body bolt mount for the 2014 was not an option. They originally listed body bolt mounted bars then changed to the panel mount based on information they received from GM. Something to do with the way the body mounts to the frame on the 2014's that GM says prevents using those bolts to mount steps.

 

This was told to me by a guy at Steelcraft, I have no other confirmation. I just know they used to sell body bolt mount steps for 2014's but no longer do.

BringTheRain403 Senior Enthusiast

BringTheRain403

Posted
Posted

I dunno man. I had a long conversation with the guy from ICI. He said the 3" round bars and the 5" Oval bars are available currently and they do in fact mount to the body mounts. I'm waiting for the 4" bars though. I just think they look way beefier...

mzodarg Senior Enthusiast

mzodarg

Posted
Posted

My friend hs the amp steps

Even though I have the factory OEM running boards on my 14 CC short box, I am looking into the the Amp power step. I personally like how you can't really see them until you open a door. Expensive, but I really like the hidden look!

 

Mike

Chris Senior Enthusiast

Chris

Posted
Posted

I havent gotten used to them. I rode in his truck today. Both times I got out, caught the board with my heel and almost fell on my ass. They are nice. Its a stock 2wd and they arent needed, but he wants to save the seats and sill plate from his wife and son.

mzodarg Senior Enthusiast

mzodarg

Posted
Posted

I havent gotten used to them. I rode in his truck today. Both times I got out, caught the board with my heel and almost fell on my ass. They are nice. Its a stock 2wd and they arent needed, but he wants to save the seats and sill plate from his wife and son.

Interesting, I for one have never had an up close and personal with them. I'll keep you're near @ss busting in mind when I finally decide.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,903
    Total Members
    8,960
    Most Online
    RyGuy43
    Newest Member
    RyGuy43
    Joined

  • Who's Online   0 Members, 0 Anonymous, 473 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • davester
      2015 Silverado 3500 right rear turn indicator failure

      By davester · Posted

      consider doing electrical testing?  I would guess some power or ground wire/connection has a problem.   alldata.com has wiring diagrams, connector pinouts and diagnostic procedures you can use to find where the problem is.
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL
    • Chuck FB
      Tire pressure for 37s

      By Chuck FB · Posted

      First off you mentioned "Toyo Says" and then gave the pressures 45/50, was this some person at the tire shop that pulled those numbers out of his head ?   Now of course I can't know your exact axle weights front and rear, however I have much the same pickup as yourself other than not knowing your starting weight as per the pounds the truck rolled out of the factory at due to the options yours did or didn't come with or what you have added beyond the extra tire weight. The correct way to know 100% where a person is at is by weighing each axle with the typical weight the vehicle is driven with and that means taking into account passengers and making sure you figure in a full tank of fuel and a little grace for whatever you may put in the bed "groceries" !    I am looking at and not that it really matters as all the tire companies use the same charts anyway, but I am looking at the comprehensive Toyo tire chart in the section that your tire falls under and I know it sounds confusing but your tire is not an LT metric tire like your factory tire but instead because its a standard inch measured tire its under a different category called an LT floatation series tire. That makes a difference as LT metric tires they don't want to see run below 35 psi at highway speed where as with the LT floatation series it can be run down to 25 psi on the highway as long as the weight on the said size of tire is agreeable with or less than that minimum 25 psi. It blows many people away that how is this physically possible, an empty truck for one thing and larger tires with the same size wheel diameter have a lot more air volume so they can carry the same weight as the smaller tire with less air pressure.    So my truck, I have the stock 275/65R20 wheels and tires and I have a bit of weight in the box with a bak flip cover and a rubber bed mat and some tools and spare gas. The front of my gas truck weighs a bit more than some trucks of the similar spec due to double batteries and alternators. However with full fuel and just me in the truck I am weighted such that I can run 40 front and 35 rear and so that is what I have done since day one.    If I base your truck at or slightly below the weight of my truck, in theory with your tires going by the tire chart you might be right around a minimum of 30 pounds front and 25 pounds rear. Of course that would hit pretty much minimum cold inflation pressure one could run with that tire size and a near empty truck. If you have access to an accurate weigh scale to do individual front and rear axle weights I would suggest you do that and make sure your topped up with fuel and whatever else in the truck before you weigh it and then you will have a great starting point to work off of and figure out what your bare minimum pressures are you can safely run. If you do much in the way of hot weather high speed driving, bumping up a bit for a safety margin is never a bad idea but just depends on what type of driving you do. I will include the Toyo chart and the floatation series sizes start on page 31. Without a doubt at these pressures I am speculating at minimum wise for your truck, it would most certainly ride very different then it did when you were using 55 lb front and rear.     https://www.toyotires.com/media/pxcjubjs/application_of_load_inflation_tables_20200723.pdf
    • Snowcamo
      Possible lifter tick after DOD delete

      By Snowcamo · Posted

      Take an automotive stethoscope to the vacuum pump. Iirc those tick as well. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...