Jump to content

Factory remote start install instructions?

Sierramax07

By Sierramax07
in Modifications & Accessories

 Share

Recommended Posts

tbarn Senior Enthusiast

tbarn

Posted
Posted

Pictures won't post properly. But heres the rest. Installation Instructions Part Number

22901614

Kit Usage

This kit adds remote start to vehicles without option BTV. The vehicle must also have AQQ and an Automatic Transmission. Both can be verified by using GM Vehicle Inquiry System (GMVIS). For proper operation of the remote vehicle start system, a hood status-switch equipped hood latch is required. For light duty trucks, a jumper harness addition is also required in order to complete circuit 109, Hood Status Signal to the Body Control Module. Adding remote vehicle start also requires programming of the vehicle. This is done using the Service Programming System. The installer must call TCSC (1-888-337-1010) to obtain a VCI number. The TCSC will provide a Vehicle Configuration Index (VCI). The VCI is good for only one specific Vehicle Identification Number (VIN). You must have the vehicle’s VIN that will be upgraded and the Authorization Code from the label on the Installation Instruction Sheet included with the kit. This will allow you to access the software to enable the remote vehicle start option.

Kit Contents

Qty

Description

1

Set of Transmitter Key Fobs (2 in total)

1

Hood Latch Assembly (with switch pigtail)

1

Jumper Harness Assembly, including strap clip attached with blue tape (Light Duty kits ONLY)

10

Tie Straps (Light Duty kits ONLY)

1

Installation Instructions (including Authorization Code Label)

Note: Due to wire routing requirements on Light Duty Pickups, please review this entire procedure before trying to perform it.

Note: When calling the TCSC, you must use the Authorization Code from the kit and have the VIN available.

Special Tools, Equipment and Chemicals Required

  • Scan Tool (with capability of communicating on GMLAN)
  • Service Programming System (SPS – TIS2WEB, or equivalent)
  • J-46079 Tire Pressure Monitor Diagnostic Tool
  • GM Glass Cleaner or Cleaner-9M905449 (US) or 00992727 (Canada) – or equivalent
  • Silicone RTV 12378479 US or 88861419 Canada – or equivalent
  • 8” (20cm) ¼” diameter steel brake tube with ends cut a 45 degree bevel – for feeding wire through grommet
  • J-38125-22 wiring connector tool

Diagram for LD PU Harness Only

3419074.giftif.gif

This diagram outlines scope of the Jumper harness for Remote Vehicle Start accessory:

Front of vehicle (1)

Plenum (2)

Plenum Grommet (3)

Harness Ground (4)

Hood Latch (5)

Procedure Remove Front Compartment Front Sight Shield

  1.  

  2. Remove the front compartment front sight shield push-in retainers (1).
  3. Remove the front compartment front sight shield (2).
Updating the Hood Latch – Required for all non-UTJ Pickups

Harness is For Light Duty Trucks Only

3419291.giftif.gif

Route 3-way connector jumper harness branch (2) along front of vehicle, in preparation for routing under Grille Mount Panel Bolt (1) and Bracket (3). Be sure to route in front of air baffle (4). As a general guideline (after driver side of the hood latch) route alongside the Hood Release Cable up to the Driver Side Hood Bumper located on the Tie Bar.

For Light Duty and Heavy Duty Trucks

 

  1. Remove and replace hood primary and secondary latch. Refer to Hood Primary and Secondary Latch Replacement.

  2.  

  3. Make connection from the Hood Latch Pigtail (2) to 3-way forward lamp harness connector (1) (or Jumper Connector for Light Duty Trucks.)
  4. Ensure that the connection is securely fastened in the positioning locator for the connector. Refer to B55 Hood Ajar Switch.
  5. This Step is For Light Duty Trucks ONLY:

    Remove the 6.35mm hole clip with strap, which is taped to the harness (blue tape) and fasten harness (4) to the air Baffle (3) 6.35mm hole approx 4” (10cm) away from connector. Tighten strap clip and cut to length.

  6.  

  7. Remove and replace grille mount panel bolt (1).

    Tighten

    Tighten bolt to 25 N.m (18 lb ft).

    Note: Ensure the bolt does not pinch the jumper harness conduit when fastening.

Installation of the Hood Latch Status Signal Jumper Harness (For Light Duty Pickup ONLY)

Routing the 3-way Connector Branch of the Harness (Light Duty Pickup ONLY)

3420307.giftif.gif

Note: Use a tie strap, part number 11509086 (10 total in kit) to secure the harness to the hood latch release cable, after the hood latch, and before the hood bumper. Cut all tie straps to length.

Fasten the jumper harness to the Hood Latch Release Cable in one location along air baffle, using tie straps (1) P/N 11509086 from the kit. (midway between the two hood cable clips (2). Secure harness along hood release cable using two additional tie straps (3) P/N 11509086. Approx distance between tie straps should be 20cm. Cut all tie straps to length.

Routing the Ground Branch of the Harness (Light Duty Pickup ONLY)

 

  1.  

  2. Route the ground ring branch of the harness along the washer bottle tube and fasten using a tie strap P/N 11509086, to the forward lamp harness head lamp connector branch. Continue to route in front of the bottle and in front of the fog lamp bracket. Accessing from underneath the vehicle, continue to route behind the front fender and fasten to the upper end of the downward branch (2) of the forward lamp harness (1) using tie strap (3) P/N 11509086.

  3.  

  4. Continue along down to the ground stud G101 (1). Remove the ground stud and fasten using BOLT/SCREW-FORWARD LAMP WIRING HARNESS GROUND, tighten to 9 N.m for ground ring, noting there may also be an existing ground from the forward lamp harness. Cut all tie straps to length.
Underhood Routing of the Hood Latch Status Signal Wire (Light Duty Pickup ONLY)

 

  1.  

  2. Following hood latch cable, route the signal length of the harness (1), inserting the harness into the C-clips (2), in two locations.
  3. Using tie strap (3), P/N 11509086, fasten in two locations between C-clips, maintaining approximately 20cm between fastening points. Cut tie straps to length.

  4.  

  5. Fasten to the third hood latch cable C-clip and branch away and toward the body harness before the grommet (3). Fasten the jumper harness (1) to the body harness using two tie straps (2) P/N 11509086 evenly spaced approximately 20 cm alternating with clips. Cut to length.
  6. Route the signal wire conduit to the body harness grommet, ensuring to create a 3” diameter drip loop (4) before positioning the taped conduit end at the grommet for entry to the interior of the vehicle.
  7. using a utility knife, cut an 1/8” slit in the grommet (3) to prepare the entry for the bare signal wire.
Routing Wire through Grommet to the Body Control Module (Light Duty Pickup ONLY)

 

  1.  

  2. From inside the vehicle, remove the fasteners and position aside the instrument panel wiring harness junction block.

    Note: Junction block connector removal is not required.

  3. Using a utility knife, cut an 1/8” slit in the thin hole of the grommet opposite of the exterior side. From inside the vehicle, insert the ¼” brake tube (2) through the back piece of the grommet (3).

    Note: Grommet removal should not be required.

  4. From inside the vehicle, carefully push the tubing through to the front of the grommet, exiting at the exterior end of grommet.
  5. From the under side of hood, insert and feed the signal wire (1) and terminal through the tubing (2) to the inside of the vehicle.

    Be sure to maintain the conduit drip loop just before the grommet entry. Verify that the grommet end does not collapse.

  6. Remove the steel tubing (2) and clean both the entry and exit surfaces of the grommet using cleaner P/N 9M905449 (US), 00992727 (Canada), or equivalent.
  7. Apply silicone to the grommet at both wire entry and exit, using silicone P/N 12378479 (US), 88861419 (Canada) , or equivalent. Leave to dry while completing the remainder of this procedure.
  8. Using J-38125-22 tool, remove any wiring in K9 BCM X4 26-way connector pin 24 (BN/L-GN) and tape back onto the body harness, if applicable. Insert the GN (green) jumper harness signal wire connector into pin 24 on the K9 BCM X4 26-way connector. Refer to K9 Body Control Module X4. Reinstall all connectors.
  9. Reinstall the instrument panel wiring harness junction block to the floor studs and install the fasteners.

Programming the Vehicle (All Vehicles)

Note: For North America vehicles, the installation of accessory remote start requires BCM programming. This is done with a Service Programming System. The installer needs to call the Techline Customer Support Center (1-800-828-6860). The Techline Customer Support Center will provide programming instructions and changes to the vehicles calibration settings. You must provide the vehicle identification number (VIN) of the vehicle to be programmed and the authorization code provided with the accessory, when calling.

Reprogram BCM. Refer to Body Control Module Programming and Setup and follow Reprogram Control Module Instructions.

Learning Transmitters to Vehicle

Reprogram remote control door lock transmitters. Refer to Remote Control Door Lock Transmitter Learn

Reinstall all removed components.

 

  • 5 years later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,758
    Total Members
    8,960
    Most Online
    Randy Ginoza
    Newest Member
    Randy Ginoza
    Joined

  • Who's Online   4 Members, 0 Anonymous, 2,121 Guests (See full list)

  • Latest Articles

  • Posts

    • CamGTP
      Gas Prices

      By CamGTP · Posted

      Paid $2.72 for E85 today.
    • Atlas
      Gas Prices

      By Atlas · Posted

      Welcome back! No, it definitely doesn't pass the sniff test. Even "ceasefire" needs an alternative definition these days.    $5.29 at Kroger today
    • bluev8
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By bluev8 · Posted

      That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
    • scotthvac.net
      2022-24 halogen - led grille swap

      By scotthvac.net · Posted

      2024 Silverado 2500 HD LTZ grille no camera Parts list   84603331 84913656 84913657 84913654 84913655 84911567 84911568 85646092 85646093 85797921 85797922   11570637  x10-15   grille/bumper bolts 11546500  x10      grille clips 11571006  x10      push/retainer clips 11546454  x6       nut retainers 11611609  x6       M5 bolts 11610700  x6       molding/trim retainers
    • davester
      Replacement Radiator

      By davester · Posted

      And use RA's 5% discount code if you buy from them.  google for the code, one is always available.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...