Jump to content

LTZ arm rest broken-replacement ideas?

oldmann
 Share

Recommended Posts

Robert A New Member

Robert A

Posted
Posted

My passenger side has been broken from the day I bought my '12 Suburban.  I've been looking since then to find a way to get this fixed without buying the whole panel.  The video a few posts back looks like a solution, but someone should sell panels with the fix already in place!

  • 4 weeks later...
2Busy2Car New Member

2Busy2Car

Posted
Posted

Hey there, I had the same problem in a 2013 GMC Chevy Silverado HD and I sprayed gap filler foam stabilizer inside and it seems to be holding up really well! I had just used the stabilizer foam to fix my cracked shower tray and it gave me the idea to try it on the truck door.  I could’ve thought about it more and made it fit better with less clean up (I didn’t have the door pieces totally set in place and the foam started oozing out everywhere) but I’m still happy with it.  I’d imagine if you drilled a small hole under the grab bar/armrest, you could fill it up with the straw and have very little clean up. It hardens within an hour too! Feeling pretty proud of myself considering I nearly pulled the trigger on a $500 door panel. Definitely wear gloves, it’s polyurethane-based and nearly impossible to get off your skin as I learned the hard way!!

  • 3 months later...
Fish1552 New Member

Fish1552

Posted
Posted

This seems to be an even easier fix.  Just pull back and squeeze in this stuff, let it cure for 2 days before really pulling hard and it's strong.  Guy even says 5 months later, it has hardened even more and is very strong.  Hell, it can't possibly be worse than the stuff GM put in it. 

 

  • 4 weeks later...
ChanceX New Member

ChanceX

Posted
Posted

So I'm new to this website, but I'm loving it so far. Alot of useful information, thanks to everyone for that. I have the same issue with the door pull being broken. When I bought my 14 suburban both front doors were broken like that, and the dealership fixed the driver side but not the passenger side. I didn't know until my passenger said the crack in the handle pinched her finger. Im still looking for a replacement door panel at auto yards around me but haven't found one thats the exact same as mine. I ended up doing the parachord fix and it doesn't look too bad. I first used some flex fix silver hvac tape to secure it and keep it from flexing since it doesn't stretch, and black gorilla tape to reinforce it and give it texture for the parachord to grip on to since the silver tape is very smooth. Then tightly wrapped the parachord and making sure it was tight with no loose spots by twisting it with my whole hand before finalizing it. It came out pretty good and definitely is stronger. Ill attach a picture of it finished. I wish i would of took more pictures for people during the process but didn't think about it til now. 

20200813_092558.jpg

  • 3 weeks later...
ggg New Member

ggg

Posted
Posted
On 1/26/2018 at 2:09 PM, grogman45459 said:

So now, almost 2 years later,  my passenger side interior arm rest/grab handle has now broken so I decided I had to do something. 

 

Not wanting to to spend $1,000.00 at the dealership to have both interior door panels replaced with the same inferior design panel had me looking elsewhere. I found a POST under a more extensive repair video on YouTube where a guy said to use paracord to repair it.

 

So I went to Walmart and picked up 2 packs of 16 ft. black paracord at $1.97 each in the arts & crafts aisle. I tucked one end of the cord in the seam under the door handle and then wrapped it tauntly the length of the handle and then tucked the end in the  seam on the other end. 

 

It fits and works perfect!! The cord gives added strength to the handle and minimizes then flex in the handle. Here’s what it looks like.

009B9022-99AC-46EE-98C9-7B6F3AF02D72.jpeg

 

  • 1 year later...
Charles Crosno New Member

Charles Crosno

Posted
Posted
On 8/15/2018 at 7:57 AM, jatkinson8755 said:

Thats not even that bad looking !

 

If anyone could spare a broken door skin, I will fabricate steel or aluminum brackets to permanently fix this stupid problem.

 

If you can spare a door skin with a broken interior handle, please pm me.  I will make a fix for you and send it back.

 

If you cant spare the door skin, then let me know the part number and I will just buy 1 and get in our shop and design a fix for it.

Would you have some already made up …. 2013 Silverado 

  • 2 months later...
Jerry Steger New Member

Jerry Steger

Posted
Posted
On 8/15/2018 at 6:57 AM, jatkinson8755 said:

Thats not even that bad looking !

 

If anyone could spare a broken door skin, I will fabricate steel or aluminum brackets to permanently fix this stupid problem.

 

If you can spare a door skin with a broken interior handle, please pm me.  I will make a fix for you and send it back.

 

If you cant spare the door skin, then let me know the part number and I will just buy 1 and get in our shop and design a fix for it.

I have a  2008 Chevy Suburban 1500. On another post you asked if anyone had a piece they could send you so you could fabricate a fix for them. I have mine off and could send it to you if you are still interested. Wanted to email you but on this forum I don't know how. You can PM me at jsteger52 through gmail if you wish.

  • 8 months later...
MsAv8tor New Member

MsAv8tor

Posted
Posted

2013 Silverado LT - Same problem with broken door handle. Ordered one from a salvage place and it was broken. Returned it. Have searched for 6 months and still no panels. You would think Chevrolet would have a replacement part not a grand fix for this. 

  • 1 year later...
  • 5 months later...
ryan35205 New Member

ryan35205

Posted
Posted
On 11/24/2023 at 9:09 PM, dlowey said:

I don't believe I can add pictures, but I am currently 3D printing replacements parts for my broken door arm rest.

 

How did that turn out?

  • 7 months later...
Nogear New Member

Nogear

Posted
Posted

Dorman  now makes a replacement - but only for the doors that have the door handle above the armrest. Still looking for a supplier that has the other option, handle below armrest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      If everything checks out at the MAF, then the MAF is BAD, new or not.   You don't need a signal generator to troubleshoot this. PCM needs ALL powers and ALL grounds able to light a halogen headlight bulb - if it can light the bulb bright, then the wiring is good enough to run the PCM.   Best thing you can do for yourself is spend some time here: scannerdanner.com - Check out all his YouTube videos on similar issues. If you decide to subscribe it's the best bang-for-buck ratio in the automotive world, hands-down. He's got TONS of free vids on YouTube, too.
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      You got that Hengst D110??
    • contrabombarde
      2010 Avalanche 5.3 not running correctly after engine swap.

      By contrabombarde · Posted

      Yes, I used my multimeter to probe all of the wires at the MAF, both with the sensor connected, sensor disconnected, key on engine off, key on engine running, etc etc etc. I probed all of the wires again at the PCM, at the connectors, etc. All voltages are what they should be according to the service manual/wiring diagrams. All grounds are good, less than 20 millivolts from the battery negative under load. Both at the connector of the MAF, at the PCM connector etc.      I know this throws a pretty big wrench into things, but this truck was acting up before the swap. I don't have very much information, if any on what was causing it, but if you cleared all of the dtcs it would do the same thing where it would crank, fire, then die. And it would do the same thing a dozen or so times, and eventually it would start and run, but the difference is that it would run and actually be drivable. Whereas now if you can drive it at all, it goes into reduced power mode almost immediately, and even then it's not running correctly. When you come to a stop at a light it stumbles down to for 500 RPM before catching itself and returning to the smooth idle. And if you go more than about 50% throttle then it immediately goes back to doing the misfire thing.    Like I said, I know that throws a wrench into things, and unfortunately I was not able to pull any data or anything like that before I did this work, so I don't have much to go on.    I'm trying to not fixate on one particular thing as the cause of the problem, but it seems like all avenues are pointing me towards the PCM. Like I said I have tested the wiring extensively (see above), and during cranking the sensor does produce seemingly legitimate values at least according to my multimeter, but as soon as the engine fires those values quickly descend into gibberish. I've tried it with multiple different known working sensors, I have done literally every test I can think of multiple times on the wiring (probing the signals, probing the pins with the sensors unplugged, probing the pins at the PCM, voltage drop, voltage drop under load, continuity, ohms, and double-checking everything against the wiring diagrams/ proper values in the service data.)    Another thing that pushes me towards a possible PCM failure is, I have noticed in troubleshooting a little bit taking a break and coming back, that when I leave the truck to sit for a while and cool off, it starts and runs smoothly when I first start it up. However once it warms up. It starts having problems. For example, when I went out to the truck this morning after it had been sitting overnight, I was actually able to drive it down the block. And then once I got on the throttle a Little bit after going about a thousand ft, it started misfiring again. I pulled it back into the driveway, shut it down, and started it back up. It idled smoothly. As soon as I touched the throttle it did the misfire thing again. From then on as soon as I started it it would misfire. I shut the truck off and went to go get a coffee and do a bit more research. When I came back out I started the truck up and it immediately went into the smooth idle. After a couple of minutes of playing around with it, it would not idle smoothly anymore. Let it sit a couple of hours, rinse and repeat. This makes me think with temperature change something is going wrong inside the PCM. I have the PCM out of the 2007 donor vehicle and I'm thinking of getting a one-day subscription to the ACDelco programming service to try and program that and see if it helps.   Like I said, I'm really trying to not fixate myself on one potential cause, but it seems everything is pointing me towards PCM failure. I would really like to try to confirm that, but unfortunately I don't have an oscilloscope or a signal generator to do the GM service procedure where you feed 5 khz into the signal pin. 
    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      Ahh, sorry about that - I got some bad info. Newdude is correct. That's what I get for working 13 hours straight ... on my "vacation", lol.   Should've checked the files I had instead of the internet.   Anyway ... this is GREAT news, since this would've been an absolute friggin nightmare to get working.   I don't think the lack of VVT is causing this - you've got another issue. Wiring, I'm betting.   I'm telling you right now, your computer isn't bad. If it worked before the swap, it's working now. You need to do some more (better) diagnostics and figure out exactly what you're missing. Did you test every wire directly at the MAF? Have 5V reference? Ground? If you're reading ZERO g/s, your Hz isn't much use - it's going to be the wrong value anyway. The MAF is not working, and you need to find out WHY.   I got this off the net, so VERIFY first: Pin A: Black (BLK) wire, Circuit 552, serves as the Sensor Return (Ground).  Pin B: Tan (TAN) wire, Circuit 472, carries the Intake Air Temperature (IAT) signal.  Pin C: Yellow (YEL) wire, Circuit 492, is the primary MAF Sensor Signal output to the PCM. Pin D: Pink (PNK) wire, Circuit 339 or 539, provides Ignition 1 Voltage (Power).  Pin E: Tan/Black wire, Circuit 552 or similar, often associated with the Intake Air Temperature ground or signal return.  Global-A list: https://postimg.cc/KKJnQC85    
    • parthery
      GM Hard Folding Tonneau by REV review

      By parthery · Posted

      Correct....the end user can't reach to Realtruck directly like they can if they purchase a Bak, Undercover, etc...  It has to go through a dealer.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...