Jump to content

Maxx Cam 5 Level Kit, Does anyone have one?, comments?

baddiesel
 Share

Recommended Posts

baddiesel Enthusiast

baddiesel

Posted
Posted

I've spent quite some time researching lifts and level kits. I've decided to install a level kit that can be installed without cutting or drilling. At $306.99, seems to be a decent price. Haven't decided on rims and tires yet, still researching info. This is a "selectable" torsion bar key, that does not over stress the manufacturers limits on the torsion bars.....according to Suspension Maxx. At any rate, all the vendors seem to perform the same method of leveling. I'm not exceeding 2.5 inches of lift. I'd appreciate any review comments or info. Thanks. By the way, this is for a 2016 2500HD, crew cab, WT, 6.5 ft bed with stock 18" steel wheels.

miker2702 Enthusiast

miker2702

Posted
Posted

save your money buy shock spacers and control arms and use the factory bars.

order you a set of differential spacers and be done with it. stress is stress raising is raising

its going to ride rougher just the say it is. control arms will keep you off the bump stops.

a lot of advertising that is no more than advertising on lots of these lifts. it will not ride like

stock cranking the bars no matter what method or product you use. now the bds kit

is another story.

boynton6spd Enthusiast

boynton6spd

Posted
Posted

I've spent quite some time researching lifts and level kits. I've decided to install a level kit that can be installed without cutting or drilling. At $306.99, seems to be a decent price. Haven't decided on rims and tires yet, still researching info. This is a "selectable" torsion bar key, that does not over stress the manufacturers limits on the torsion bars.....according to Suspension Maxx. At any rate, all the vendors seem to perform the same method of leveling. I'm not exceeding 2.5 inches of lift. I'd appreciate any review comments or info. Thanks. By the way, this is for a 2016 2500HD, crew cab, WT, 6.5 ft bed with stock 18" steel wheels.

I'm looking at the kit as well!

I like that it includes shock and diff spacers!

baddiesel Enthusiast

baddiesel

Posted
  • Author
Posted

miker2702, is the BDS kit a "leveling kit"?

 

boynton6spd, I called Suspension Maxx today. I asked them If I raise the truck 2.5 inches, would a 34" tall, 11" wide tire rub, and the representative told me "no, it would not". I also asked if I needed to replace the upper control arms, in order to prevent rubbing, and his response was also "no". So.....I went further with soliciting questions regarding fitment. I asked him if I installed factory 18" aluminum alloys (eg have proper backspacing and offset), with Michelin LTX M/S2 295/70R/18, load range E, would there be any issues rubbing(?) And again, his response was "no". He mentioned that sticking to factory spec wheels was a lot easier, and a lot less problems. I'm trying to make good choices with this application. My truck is a daily long distance driver, so I kinda prefer a tire that I can get the most mileage. I rotate my tires and change my oil/oil filter every 5K miles. Yep, I've got OCD. Thanks for your comments!

miker2702 Enthusiast

miker2702

Posted
Posted

Bds is the more expensive kit

Being offered. Should have a better than stock ride. There is a thread in last few days on here if some one putting one on.

There is a reason cognito sells

So many control arms. Once you tighten the bar suspension travel is limited. Not rubbing

Just doesn't mean tires. Frame stop and upper control arms

Can be annoying.search threads on here many discussions on the subject.

baddiesel Enthusiast

baddiesel

Posted
  • Author
Posted

I gotcha' miker. I researched the 2-3" BDS coilover lift that eliminates the torsion bars all together. It looks very high tech, and at that price, it should be. I really do like it, I'm going to call the local authorized installer for a price on the installation. *One thing that I did not like...the only stock rim I can use is the 20" x 9". I do not like 20's at all. I prefer a 17" or a 18", but in this application, it will have to be an aftermarket rim. I do not know what the correct offset or backspacing is required. I don't like the look of "outriggers" on my truck. I wanted to run Michelin LTX MS2 295 x 70R x ? I don't know if Michelin makes a bigger LTX than that. Thanks again for the info. The BDS is quite a bit more expensive, but since this will be my last truck before retiring, I would like to do this truck "right" the first time.

miker2702 Enthusiast

miker2702

Posted
Posted (edited)

if money is not a big concern I would look seriously into eliminating the torsion bars etc.

I hate 20s as well I bought some for my work truck but still driving around on the stock

steel wheels. but the trade off in ride I could learn to like the 20s. look to the bottom of

the page when you first open the forum and ask the guy his opinion.

 

http://www.gm-trucks.com/forums/topic/202235-bds-coil-over-2-3-kit-installed-on-2500hd/

Edited by miker2702
baddiesel Enthusiast

baddiesel

Posted
  • Author
Posted

Miker: Thanx, I appreciate the info. Looks like all I have to do, is research an aftermarket 17" x 9" or 18" x 9" wheel. I've picked out an installer/vendor in Charlotte, and he recommended a website to visit. Again, I really appreciate the info, I'm not a young guy, and I want a nice smooth ride. I use my 1977 CJ7 for off road, but my truck must remain reliable, and not abused.

  • Like 1
baddiesel Enthusiast

baddiesel

Posted
  • Author
Posted

Talked to an authorized vendor/installer yesterday. He said to look at 17 x 9's or, 18 x 9"(8 x 180mm bolt pattern) with 5.5" backspacing. Just thought I'd share some helpful info, if you prefer something other than stock 20's. I prefer a larger tire profile, and they're a little cheaper on your wallet.

miker2702 Enthusiast

miker2702

Posted
Posted

Glad it worked out for you.

I'm not a experts at all on these truck s. Went looking

For a.used 1/2 ton ended up

With a new 2016 2500 crew 4wd

For 29k.couldn't stand the severe rake they have.

  • Like 1
baddiesel Enthusiast

baddiesel

Posted
  • Author
Posted

Congrats on your new truck. I had a 2016 1/2 ton for about a month, and got rid of it. That cylinder de-activation, and clueless transmission shifting and vibrating turned me off. I could put 1500 lbs in the back and it was too much for the truck. I'm glad I went with the HD2500, it shifts flawlessly, and hauls the weight. It might be a bit thirsty, but I am more than willing to pay the price for a decent running truck. Plus, it's very comfortable.

4wdriver Enthusiast

4wdriver

Posted
Posted

Congrats on your new truck. I had a 2016 1/2 ton for about a month, and got rid of it. That cylinder de-activation, and clueless transmission shifting and vibrating turned me off. I could put 1500 lbs in the back and it was too much for the truck. I'm glad I went with the HD2500, it shifts flawlessly, and hauls the weight. It might be a bit thirsty, but I am more than willing to pay the price for a decent running truck. Plus, it's very comfortable.

Glad yours shifts flawlessly mine is often confused

  • 5 years later...
henny123 New Member

henny123

Posted
Posted

Maxx Cam 5 Level Kit is a great addition to any home studio or music room. This kit includes everything you need to record in a professional studio setting: two mics and two stands, a control room monitor stand, and a headphone amp. The Maxx Cam 5 Level Kit is the perfect choice for recording vocals, acoustic instruments, and electric bass. It provides an excellent audio experience with minimal noise. And best of all, this kit is affordable and easy to use. If you're looking for a budget-friendly solution for recording in your home studio, then Maxx Cam 5 Level Kit is the perfect choice for you.

heardle

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      The Peckish Synapse

      By Atlas · Posted

      One of the few things I enjoyed about my time in the midwest was taking off on weekend drives. Unlike home, where we are boxed in by mountains and water, those rules don't apply to the inland plains. Roads connect and sprawl everywhere. While Minnesota is flat, it's not completely featureless and there are fast moving rural roads with curves and slight elevation changes. I used to relish heading out in a particular direction with no set destination, no curfew, and weaving through little townships, wherever the roads would take me. Along farms, lakes, or through the deciduous trees... It was beautiful in its own way, and the seasons were so distinct there. Fall drives yielded amazing shows of color and contrast. Summer drives rewarded with the and amber evening glow of the prairie (and lots of juicy bugs).    I do a lot of that here in my home state too. But it's much less mysterious/intriguing. I've traveled most roads in the region, and every road that's fun to drive within a good radius of my house. But every drive, even on the same old roads, is still enjoyable. I know where I can lean hard into the throttle or really throw the car into a curve. There are exercise loops for when I just need to keep certain cars limber, and much longer routes to settle in and enjoy a drive and put some miles on. All the mountains and water make for some really awesome roads for spirited driving. But not all my driving is spirited, for example, that's not really enjoyable in my pickup or this Blazer (that's still here...).   Sometimes a good drive is followed by a ritualistic wash before tucking the car away...
    • C/K Man
      L8S For 2027

      By C/K Man · Posted

      'GMAuthority' is reporting the 2027 HD's will have the L8S 6.6L gasoline V-8.  There was some talk here about the L8S awhile back.  Not sure what changes it will have now as it seems the 2027 emissions regulations have changed from what was originally proposed.  The big question will be is L8S just a stopgap for the last 2 years of the current T1 HD platform or will it carry forward to the next generation 2029 T1-2 HD's?    I assume the L8S will still be a Gen. V engine. 
    • bruceb58
      New Duramax rumor?

      By bruceb58 · Posted

      New engines will still be using DEF. You just won't have the limp modes occurring when you run out of DEF now.
    • bruceb58
      first oil change - 2026 2500HD gas

      By bruceb58 · Posted

      I am not a NOCO fan for a charger I would leave on a battery 24/7. The reason is, it doesn't really float. It waits until the battery drops to a certain voltage and then charges it back up to 14V. It's better than no charger I guess.
    • bruceb58
      first oil change - 2026 2500HD gas

      By bruceb58 · Posted

      I would never do anything but lithium.   If the vehicle is stored, just turn the disconnect off. My batteries are completely disconnected form everything in the trailer when my disconnect is off. Trailers don't always come that way as some still keep the CO/LPG monitor on. When mine is off...it is off.   As far as storage temps, LiFePO4 are good down to -20°C. I would store them in a heated place if it goes below that. You can also get heating mats with a thermostat if power is available.   The way the heaters work, if it's below 0°C, if a charge comes in, it is directed entirely to the heater until the battery gets above 0°C and then it allows the charge to go to the battery.   For my Android tablet I use as a display, I can move it inside my house if I was ever in an area that got super cold.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...