Jump to content

No Reverse Lights and "Service Rear Vision System" message

CamperBurn

Recommended Posts

CamperBurn New Member

CamperBurn

Posted
Posted

Long time lurker but 1st time poster here. I have a 2015 Z71 LT with factory back up cam. about 2 weeks ago my rear back up cam stopped working and i started getting the "Service rear Vision System" message.  last night I also notice that my reverse lights are not working when i put the truck in reverse. I have checked fuse 16 and 33 under the hood which show to be back up lamps, both are good. Any other ideas? Is it just a coincidence that both stopped working. i think the problems are likely linked together. I tried to search but didn't find anything. Any ideas? 

xMEATxHAMMERx Enthusiast

xMEATxHAMMERx

Posted
Posted

I'm guessing it's not just a coincidence. I'm not sure what is used as a signal to activate the back up systems tho. Could be a sensor in the transmission, or even just a bad ground wire. I would start with a tester and work my way from back to front starting by the spare tire. Your camera and tail light wires come from a module above your spare tire, just inside the frame on the driver's side.

Long time lurker but 1st time poster here. I have a 2015 Z71 LT with factory back up cam. about 2 weeks ago my rear back up cam stopped working and i started getting the "Service rear Vision System" message.  last night I also notice that my reverse lights are not working when i put the truck in reverse. I have checked fuse 16 and 33 under the hood which show to be back up lamps, both are good. Any other ideas? Is it just a coincidence that both stopped working. i think the problems are likely linked together. I tried to search but didn't find anything. Any ideas? 


And as always... Enjoy your ride!

Sent from my SM-G955U using Tapatalk

CamperBurn New Member

CamperBurn

Posted
  • Author
Posted

Thanks,  good to know on the on the module above the spare tire. It would have been nice for this to happen about 3k miles ago when it was still under warranty.

  • 1 year later...

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • richard wysong
      Gas Prices

      By richard wysong · Posted

      Diesel $5.42 at the truck stop on the hi-way
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

    • txab
      Gas Prices

      By txab · Posted

      $3.59  
    • needafix
      2019+ Brake failure, it's complicated

      By needafix · Posted

      I'm not sure if this should be a new topic, let me know if it's out of place. This my first post. Thanks 85077522 - AC Delco GM Genuine Parts Brake Master Cylinders. Anyone else had to replace this brake master cylinder yet. I didn't do any brake work, it looks like new parts and I've had the truck for about 4k miles, 119k total miles.  When it started to throw codes I did the calibrations with a bidirectional scanner and got the codes to clear but they came back so I did the routine; base bleed, automated bleed and final base bleed. All that with Bosch ES16-32N fluid (please look it up). That seemed to fix it but 100ish miles later it failed again so I ran the same process but with a pressure bleeder this time and got the same results, fixed for 100ish miles. The original fluid looked bad and I thought I got most of it out, it could've been the wrong fluid. The codes; P25A2, C05B0-00, C2A1B. I can get them to clear but not for long. The C05B0 indicates a leak in the front circuit (which is bone dry) so I'm thinking of doing the bleed process on that front again today and I don't know if that's taboo to just do the front but at this point it seems like it's worth the try anyway. The new master cylinder/module unit is supposed to get here today. But now I'm pretty much convinced this install is over my head. I've called several shops and some mobile guys that I know but this thing is like radio active material, scary wise. I did get 2 local shops say they should be able to do it, one says he has the SPS2 programing capability. And with the battery disconnected is there supposed to be pedal resistance, mine is to the floor, then if I pump it I can get some resistance. I had a panic stop prior to this issue which may have contributed from what I read. And on the first attempt to bleed and hydraulic test the scanner listed things to look for and one was any gaps between the pad and rotors which I did notice on the RF corner and I removed the outer pad (where the gap was) cleaned it and the hardware and didn't see a gap after that but will re-check it. I read that if pushing the caliper pistons back then you're supposed to open the bleeder so as to not push fluid backwards into the abs module or it will damage it. If that's true then that's also a possibility from the previous owner having the brakes changed before I got it. I'm using an XTool ip500 scanner. Any suggestions, questions and comments welcome. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      Next Friday will be my 6 week point from my right knee replacement.  The surgeon says it will be fine if I choose to drive after this checkup.  I know I could drive now but best to do as my surgeon (and my wife) tell me.  Richard compared being 62 to 72.  I remember when I was in my early 60's I was experiencing slow but regular decline in my mobility.  Thanks to good medical support,  i continued to fight the speed and spread of this decline. During my 60's I worked on non-surgical methods and just when I turned 70, my orthopedic surgeon recommended joint replacements.  In a little over a year, I had one shoulder and both knees replaced.  This hasn't been a terribly fun experience, but worth the discomfort as my future mobility health trajectory has reversed.  It is a treat to now be watching my mobility. balance and confidence steadily improve!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...