Jump to content

2018 silverado eassist lifted

FrankJNo
 Share

Recommended Posts

  • 6 months later...
3tspapat Enthusiast

3tspapat

Posted
Posted (edited)

What's your concern as far as being an eAssist vehicle? 

Edited by 3tspapat
Ricardo Rodriguez New Member

Ricardo Rodriguez

Posted
Posted

I’ve been inquiring also since i also have a Eassiat 4x4. According to Procomp and Rough Country, their kits aren’t compatible. Superlift said the same thing when I mentioned that to them. If FabTec worked on your truck then I’ll go with FabTec also. Is your’s the Gen 1 or Gen 2 lift? Also, can I install Bilstiens 5100’s and does everything pertaining to Eassist still work as it should after you lifted yours?  Also did the kit come with a brake line and did they use it. Thanks for your help. I really would like to lift mine.

  • 2 months later...
Carl C2 New Member

Carl C2

Posted
Posted

My truck is a 2018 GMC Sierra 1500 w/E-assist.  I lifted it with a 6” Superlift and 35 inch tires. If you plan to program the ECU or calibrate the speedometer I wish you luck. I haven’t found anyone that offers what’s needed for E-assist. 

D7979B9D-FA14-4CBA-A51E-552DE78B00C2.jpeg

  • 6 months later...
Chunko New Member

Chunko

Posted
Posted

Bumping up an old thread.  Anyone have advice for lifting a truck with eassist (hybrid)

3tspapat Enthusiast

3tspapat

Posted
Posted

You can do it fine. You may have issues finding someone who can calibrate the speedo for the tire size. I'm pretty sure the dealer can do this. 

  • 6 months later...
Ricardo Rodriguez New Member

Ricardo Rodriguez

Posted
Posted
On 6/11/2019 at 1:31 PM, Ricardo Rodriguez said:

I’ve been inquiring also since i also have a Eassiat 4x4. According to Procomp and Rough Country, their kits aren’t compatible. Superlift said the same thing when I mentioned that to them. If FabTec worked on your truck then I’ll go with FabTec also. Is your’s the Gen 1 or Gen 2 lift? Also, can I install Bilstiens 5100’s and does everything pertaining to Eassist still work as it should after you lifted yours?  Also did the kit come with a brake line and did they use it. Thanks for your help. I really would like to lift mine.

I just finished lifting my 2018 eAssisted Silverado. I went with an 8 inch Superlift, 24 MotoMetal with -76 offset, Amp Terrain Attack 35x13.50's, and Bilstein Shocks front and back. The installation went smoothly, no issues at all, the ride is better than stock.

mqzqFRTw.jpeg

  • Like 1
  • 5 months later...
tp503 Enthusiast

tp503

Posted
Posted

Older thread but still throwing in my experience. I put a 6" Fabtech suspension lift with 20x10 Fuels and 35" K02s on my 2018 GMC Sierra 1500 SLT w/ eAssist. I also installed a Volant cold air intake, and a custom exhaust. The main thing that caused problems was the intake because of the location of the coolant reservoir not normally in that spot but there because of the hybrid battery. Just had to get creative with moving it out of the way a couple inches. There was rubbing from the wheels but that stopped after I removed the stock fender flares and installed some Rough Country flares. With all the work done, I then added a Range AFM Disabler to run on 8 cylinders at all times. In hindsight, I would not have gotten the eAssist but that's all the dealer had coming on the truck at the time and it's worked out okay.

  • Like 2
3tspapat Enthusiast

3tspapat

Posted
Posted

Yea eAssist is a bit of a pain, especially with programming. Other than that, it's a fine truck. 

  • Like 1
  • 3 weeks later...
tp503 Enthusiast

tp503

Posted
Posted (edited)

Has anyone used a speedometer calibrator on their eAssist after bigger tires? I got a Hypertech Calibrator but the hardware doesn't have it programmed for the eAssist and the software couldn't find compatible settings in the internet sync, so it sent my system specs back to Hypertech for the engineers to look at. I imagine not too many eAssist owners lift their trucks so they don't have enough demand to calibrate for eAssist ECUs. 

 

UPDATE: Hypertech added availability within a few hours of the automated request from the software. Speedometer is now calibrated!

Edited by tp503
  • Like 1
MikeBMW Senior Enthusiast

MikeBMW

Posted
Posted
3 hours ago, tp503 said:

UPDATE: Hypertech added availability within a few hours of the automated request from the software. Speedometer is now calibrated!

What is this speedometer calibrator of which you type?

tp503 Enthusiast

tp503

Posted
Posted
31 minutes ago, MikeBMW said:

What is this speedometer calibrator of which you type?

It's just called the Hypertech Speedometer Calibrator. Was $170 on Amazon. I'm in the middle of trial and error right now to get it perfect. I have 35's but entering that didn't give me a correct reading. Now stepping down in 1/4" increments to find where it registers accurate speed.

  • Like 1
MikeBMW Senior Enthusiast

MikeBMW

Posted
Posted
Just now, tp503 said:

It's just called the Hypertech Speedometer Calibrator. Was $170 on Amazon. I'm in the middle of trial and error right now to get it perfect. I have 35's but entering that didn't give me a correct reading. Now stepping down in 1/4" increments to find where it registers accurate speed.

Thanks, I, also, have 35s. I'll take a look at it, much appreciated!
My MaxiSys Elite can only change the tire type and pressures but no speedo re-calibration and the guy at the Chevy dealership mentioned it wasn't possible at the dealership.
Again, thanks!

tp503 Enthusiast

tp503

Posted
Posted (edited)
30 minutes ago, MikeBMW said:

Thanks, I, also, have 35s. I'll take a look at it, much appreciated!
My MaxiSys Elite can only change the tire type and pressures but no speedo re-calibration and the guy at the Chevy dealership mentioned it wasn't possible at the dealership.
Again, thanks!

I am VERY close at 33.50" (the actual measurement from ground to top of tire right now). If I go to 33.25" I think it will be perfect. Each tweak takes me about 20 minutes - revert to stock then load new settings then drive and compare to Google Maps speedometer.

Edited by tp503
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,972
    Total Members
    8,960
    Most Online
    Whit.the.COB
    Newest Member
    Whit.the.COB
    Joined

  • Who's Online   5 Members, 0 Anonymous, 1,383 Guests (See full list)

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Declaring victory would upset the demons that possess this Blazer, so I won't. But I did make progress today--after it put up a fight. Always a fight.   I had the day off so I spent the morning cleaning up the shop and I thought I'd get ahead of things by filling the cooling system in prep for the final part I needed to arrive: the driver's side knock sensor. Glug, glug, glug....and then the unmistakable sound of liquid hitting the shop floor. It induces the same chagrin when the sonar and targeting laser temporarily malfunction during a late night bladder evacuation over the toilet with the bathroom light off. D'OH!!! That made a mess...   Oh, hey, that knock sensor I removed? It threads into a wet port. Who knew?! Learn something new every day. Put a pin in that chore, I'll fill it the rest of the way later.   The knock sensor arrived at about 1pm. I threaded it in, connected the wire, filled up the coolant, checked for leaks, and... drumroll.... fingers crossed for a perfect start, excellent timing, model fuel trims, and ...no squeaks... Here goes.....   No, it didn't start. At all. I cranked it a few times and it wasn't sounding good. Furthermore, I heard leaking again. Jesus H Tapdancing Christ, stop leaking all over the dang floor. This time I had accidentally overfilled the coolant reservoir and the churn of the water pump via cranking caused a bit to burp out. Ok, just, breathe... Put the flamethrower down. Dang thing wouldn't burn anyway, leaks too much...   Did you know the rotation of a round crank sensor in a round hole, matters? I do now. Took me about half hour to retrace steps and realize what I had done. Then it started right up.   No squeaks. The squeak was the old balancer.   Once it entered closed loop, fuel trims are dead on, hovering right around zero at idle. No more -30%. I'll credit the injector rebuild on that one.   Timing? I think there's an OBD 1.5 translation error with my Actron scanner. It's anywhere from -20 to -30 at idle, sometimes as high as -40 cruising. Sorry, the engine just isn't running that smoothly at -40 degrees ignition advance. It's just not. It's smooth all through the rev range and has decent power. I'm going to have to trust the seat of my pants on this one.   The new exhaust is very quiet. The old catalytic converter? Not melted, but definitely not healthy. Rains glitter when you turn it on its end...all the precious metal is flaking out. Once the new exhaust system burned in/smoked off a bit, the engine's exhaust smell is normal again. Not that I'd recommend going around huffing car exhaust, but, you know what I mean?   One problem to correct. The new exhaust has the opposite problem of the old spliced up exhaust. It wants to hit the floor where the old one wanted to rest on the cross member. Happy medium, please? Still noodling on that one, need to look at how I can adjust some hangers.   I don't know what's next. On one hand I want to run away from this thing as far and as fast as I can -- there have been a lot of NOT fun moments. On the other, now that it kinda drives nice, maybe drive it around for a little bit?   Shhh... it's not currently dripping oil all over the floor. I can see just a little wet at the bottom of the timing cover where it meets the oil pan seal. It's not dripping multiple drops with every ignition cycle, in fact, after some driving this evening it has yet to even form a drop that could drip off yet. But the weekend is young... I fully expect this could turn into Exxon Valdez by Sunday. Because this Blazer hates me. LOL.      
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      About that:   Once upon a time in a land far far away lived a car company that was shy about taking your money and wanted to be sure that they gave you more that you asked for so that you'd come back. No really, not a fairytale. 😱   But after the field got thinned out enough to limit the competition it seemed good enough to give you only what you asked for. Fair enough I say but in such a market you have to give something the others are not or they go to the one who does. Gimmicks or glitz. Oh, fins and chrome. Yea, shinny crow like cars. Yum.    Field narrows a bit more and 'brand loyalty' becomes a thing and the minute it does they start thinking to themselves, "Could we make more money if we gave them less than they expect and they will hang in there for brand and comfort with the known?" They gave it a try and da*n, it worked!!    Well, what if we teach them, groom them into believing that less is "Normal" and cut some more corners. Will that work? Oh heck yea!    🤔 I wonder, can we give then WAY less than they expect and make them mad enough to spit nails and STILL get them to pay up? Sure, if we get everyone else to do the same so that the choice is less or nothing at all. How would be do that? Platform sharing.  What a concept, right?  Steal like there is no tomorrow and it's legal too!    Truth is no one is going to give up driving, not for very long. The Gen Z crowd is fine with it and will be as long as someone not Gen Z will haul them around. At some point we all die.    Economic voting only works if you cast a NO vote now and again and enough of them to get dumb and dumber to wise up. Well, that's how I was taught anyway. And it should have worked. Would have worked. But the Bail out!!   Look, you have another choice if  you take that bag off your head. If the dumb it down to some predetermined expectation of how John Q Public will use it the, that is under design it to failure they you use it to a lower stress mode. D'ho!    A 1950 Royal Enfield Bullet 500 will go anywhere a Suzuki Hayabusa will and for just as long. But you will have to treat it for what it is and not for what you wish it was. 
    • Vu1can
      Bridgestone vs Goodyear tires?

      By Vu1can · Posted

      Maybe I was just too unlucky, but I had nothing but bad luck with Bridgestones. Out of 3 sets, they all started losing a lot of air when they got down to about 1/2 tread life, and at that point also wet traction suffered more than it should have. Also, the only tire I ever had in my 60 years of driving that had a side wall blow out was a Bridgestone.   I'm currently running Goodyear Wrangler Workhorse AT and am very happy with them.   
    • davester
      Broke Down on the Mountain

      By davester · Posted

      maybe when the trip is over, check all the other joints in the front end, like all the ball joints, tie rods, pitman & idler arms, etc...
    • Carlos Eduardo Silva
      adding 360 surround view, UVI (Trailer Camera) package to UVS (Surround/invisible Trailer) Upgrade 2020 Silverado RST

      By Carlos Eduardo Silva · Posted

      Thks, and actually it was my bad, because here in this post there is someone showing the correct wire position as well. My bad... But thank you a lot with the help as well. I was able to find and buy a 10 channel VPM that came from a sister silverado of mine. The same year, same mode, same trim, same everything. 2022 Silverado 1500 LTD LTZ (pre-refresh). I also found to buy just the bottom mirror part that has the cameras, so way cheap than the full mirror. + a used front camera. I did test everything together, cameras, cables and the VPM.... everything worked EXCEPT my original Bed camera and the backup grid lines. I think the reason is because now I need to do the VPM reprogram. I sent a msg White Automotive & Media Service to confirm that it is the problem and that they can do it service for me case.   Once I get it 100% done I will post here result....

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...