Jump to content

SLE bumper cover upgrade

First Time Truck
 Share

Recommended Posts

First Time Truck Enthusiast

First Time Truck

Posted
Posted

Hello everyone,

 

I am new to the Sierra family, just picked up a 20 Sierra SLE 1500 and enjoying the truck so far. Looking forward to learning from everyone here on the forum. I have a few mods in mind but want to start with fog light installation. I noticed the higher end trims have a different bumper cover with a different part number that allows for the trim bezel piece insert, does anyone know if these parts are interchangeable, the SLE does not come with fog lights or the bezel/clip and I want to add this to the look of my truck, if I were to obtain the SLT, Denali, or AT4 bumper cover would it fit on my truck that way I can have the fog light trim bezel?

 

Thanks in advance,

Mora84 Enthusiast

Mora84

Posted
Posted
52 minutes ago, First Time Truck said:

Hello everyone,

 

I am new to the Sierra family, just picked up a 20 Sierra SLE 1500 and enjoying the truck so far. Looking forward to learning from everyone here on the forum. I have a few mods in mind but want to start with fog light installation. I noticed the higher end trims have a different bumper cover with a different part number that allows for the trim bezel piece insert, does anyone know if these parts are interchangeable, the SLE does not come with fog lights or the bezel/clip and I want to add this to the look of my truck, if I were to obtain the SLT, Denali, or AT4 bumper cover would it fit on my truck that way I can have the fog light trim bezel?

 

Thanks in advance,

https://www.ebay.com/itm/2019-2020-New-Gen-Sierra-GM-Fog-Lamp-Light-Kit-84822219-WITH-TASK-LIGHTING-OEM-/153220220859. 

First Time Truck Enthusiast

First Time Truck

Posted
  • Author
Posted

Thanks for the response, however I was hoping to get information on the silver trim ring around the fog lights. The higher trims have inserts in the bumper cover that the trim ring attaches to. Is there any info on the bumper recovers being universal to all 1500 models?

tmo Enthusiast

tmo

Posted
Posted

You would need the plastic upper bumper from the SLT+. Then you could get the trim pieces you are looking for. I think the fog lights are probably the same with just different surrounds.

87040112d01f6fd8cc077ebb06db504f.jpg

Unknown_eyes Enthusiast

Unknown_eyes

Posted
Posted

It's interchangeable. Just a matter of getting the required parts and paint work. Here's some of the parts required not including the wiring, switch, and dealer programming to make them functional. 

 

I installed the gm accessory fog kit shown above on my sle. But used a harness from gen5diy.com that doesn't require dealer programming.

 

 

 

pixlr.jpg

First Time Truck Enthusiast

First Time Truck

Posted
  • Author
Posted
On 8/28/2020 at 7:37 PM, Unknown_eyes said:

It's interchangeable. Just a matter of getting the required parts and paint work. Here's some of the parts required not including the wiring, switch, and dealer programming to make them functional. 

 

I installed the gm accessory fog kit shown above on my sle. But used a harness from gen5diy.com that doesn't require dealer programming.

 

 

 

pixlr.jpg

Thanks for the help!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Parking Brake - Automatic Engagement Questions

      By Another JR · Posted

      On 2021 3500hd it consistently sets automatically when selecting park if the incline/decline is above a certain angle. 
    • Policeoff01
      Feeling Vibration and Jiggles in 2024 HD Gasser Steering Wheel

      By Policeoff01 · Posted

      Curious, did anyone ever get a fix for the vibration reported here.   I have a 2024 Silverado with 6.6 duramax.   I’m noting the same vibration resonating up through the steering shaft into the steering wheel.    Best way to describe- like someone is tapping on the steering shaft/components and it’s resonating into the steering wheel.    thanks. 
    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...