Jump to content

Recommended Posts

Posted (edited)

I'm looking to put headers on my '14 sierra 5.3, the issues rises as i'm in NY state with their BS emissions inspection. Anyone in NY have options that they have done successfully? TIA

Edited by MtN33R
Posted

Where in NY are you? I've done full exhaust systems in previous vehicles (including headers) and had no issues with passing inspection. I used to bring one of my vehicles to the dealership to inspect just because it was easier for me (and that car was highly modified). As long as you don't have a CEL you should be good to go.

Posted

I'm in sullivan county, NY. Thats what im afraid of is a CEL because of the o2 sensors,  I rather not spend $1700 on high flow cats with long tubes. Just weighing my options here with some research before dishing out the doe!

Posted

try doug thorly  tri-y's torque headers...going by Cali emmisions .. as long as you got cats on and the check engine light ain't on , your good!

Posted
On 9/11/2020 at 6:10 PM, MtN33R said:

I'm in sullivan county, NY. Thats what im afraid of is a CEL because of the o2 sensors,  I rather not spend $1700 on high flow cats with long tubes. Just weighing my options here with some research before dishing out the doe!

I’m in Orange County right below you. I have Texas speed headers with no cats. Before I had my rear monitors turned off, I ran 90 degree o2 extensions, CEL never came on. Had it inspected twice so far by Barton Birks in Newburgh with no issues 

Posted
21 hours ago, Kyle Coleman said:

I’m in Orange County right below you. I have Texas speed headers with no cats. Before I had my rear monitors turned off, I ran 90 degree o2 extensions, CEL never came on. Had it inspected twice so far by Barton Birks in Newburgh with no issues 

Thanks for the input man. Looking at the TS headers and y pipes they're pretty reasonably priced, might send it with a pair of their LT's and catted y pipe.

Posted
2 hours ago, MtN33R said:

Thanks for the input man. Looking at the TS headers and y pipes they're pretty reasonably priced, might send it with a pair of their LT's and catted y pipe.

Definitely do the catted y-pipe. I didn’t and it’s way to loud 

Posted
On 9/16/2020 at 7:28 PM, Kyle Coleman said:

Definitely do the catted y-pipe. I didn’t and it’s way to loud 

Haha for sure man, this is my daily driver so don't want it to be obnoxious.

Posted

Wow....great information. I’m in upstate and have been thinking about this myself. I’m in Saratoga county. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 
    • In the 80's 90's I'd run Honda's 7,500 miles between changes using Red Line HP 5W20 and do it for hundreds of thousands of miles with issues. Back in the day it was an SAE 20 with the HTHS of a SAE 30 and SN add load. It was also very polar. Oxidation VOA was over 120. Besides those motors were SPFI and lean burn tech. I could have likely run it longer but never did.    We had a Toyota bought new I ran on Pennzoil's latest and greatest synthetic of the day with "Penthane". A made up word for a very low dose of PAO. Tried 7,500 mile OCI's in that Group III/VI chemistry and the rings tapped out at 90K. Rocker box wasn't as bad as the one Punch put up but it wasn't good either. Also a SPFI motor.    I'm around 3,750 across the board on these GDI monsters and the oil it tapped out by then usually on TBN/TAN crossover and color. Red Line HP Euro.    The AMSOIL SS brochures tell you to follow the OEM values for the service class but that it can be run up to 25K if monitored. I can't imagine what motor could go that distance and not tap out. I've never owned one.    Yes, I know. Lot's of people do. I'm just not going to be one of them. 
    • I knew a guy in the early 80's that bought a new Monte Carlo and ran it a 100,000 miles without ever changing the filter or the oil. Just kept adding. It looked like that inside.     
    • Good evening. I was lucky enough to get passed down to me a 2007 GMC LBZ that was my great uncle's. While the underside and rockers are more or less gone I feel like with time I can restore it to working order since it only has 110,000 miles and he put nearly every option he could get without getting the new body style since he did not trust DEF. So far I have done everything I can think of but when I put the key into the ignition nothing happens. I put 2 brand new batteries in it. Cleaned the terminals. Check all the fuses and relays and they all pass with my multimeter. I know I'm missing something that I just cant think of. The only odd thing is the OBD2 port works which makes me think its not the mega fuse. Any advice would be greatly appreciated. 
    • Looks nice. I still have my 2000, 1500. Bought a 2025, 1500 for retirement. Feels solid. These trucks have a bad rap on the internet. My brother has a `24 1500, 5.3 with 52,000 miles. No problems at all. Mine hasn`t either but mine`s only at 12,700 miles. Have seen some of these things with 100,000 miles with no problems.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...