Jump to content

Transmission Cooler Upgrades?

BCMoto

By BCMoto
in Engines & Drivetrain

 Share

Recommended Posts

BCMoto Enthusiast

BCMoto

Posted
Posted

Hey all just trying to search for some trans cooler upgrades if any? Lately we have been out on trails and trans temps have been climbing and I want to address it before it gets bad. Temps currently sit around 200 degrees in 4 Hi and on a trail. If im doing more wheeling it can climb higher. The truck is a 2018 with 6.2L sitting on n35s any help will help

CamGTP Senior Enthusiast

CamGTP

Posted
Posted

Is that with the inline transmission thermostat still in place?

 

Honestly you'd need to add a fan to any cooler if you are barely moving to help lower temps. Seeing 200 degrees isn't hot either, no need to really worry until you are pushing 230+ consistently.

Bash74 Enthusiast

Bash74

Posted
Posted

I would flip the pill in the transline. Those 35s are not helping either unless you re-geared, which in my opinion every person should do going to 35s or larger. As already stated definitely add a fan.

Sent from my SM-G975U1 using Tapatalk

BCMoto Enthusiast

BCMoto

Posted
  • Author
Posted

Yes I haven't done anything to the transmission thermostat.

 

I am regearing soon to 4:10 gears

 

If I do upgrade to a larger cooler I would want additional fans on the cooler.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,903
    Total Members
    8,960
    Most Online
    RyGuy43
    Newest Member
    RyGuy43
    Joined

  • Who's Online   5 Members, 0 Anonymous, 522 Guests (See full list)

  • Latest Articles

  • Posts

    • AlVeron
      Manufactuer's Defect - Paint Failure - Cherry Red High Country 2021 Suburban

      By AlVeron · Posted

      This is NOT impact damage nor neglect. There were previous class action lawsuits because of such paint preparation st GM manufacturing plant. Not just the Cherry Red Color. This paint is applied in three processes to obtain the desired color.  The manufacturer will cover for 36 months or 36k miles only. That rust is actually corrosion because of the paint process failure. Corrosion is covered for 100,100 miles or a certain months. However their corrosion doesn't include this type. Go figure. Clearly manufacturer knew from previous paint issues. This started 3 weeks ago out of the blue.  
    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      Is it time to put a piece of tape over the CEL? 
    • davester
      2015 Silverado 3500 right rear turn indicator failure

      By davester · Posted

      consider doing electrical testing?  I would guess some power or ground wire/connection has a problem.   alldata.com has wiring diagrams, connector pinouts and diagnostic procedures you can use to find where the problem is.
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...