Jump to content

Recommended Posts

Posted

I have 2006 gmc sierra 1500 4wd 5.3l. I can't find out what's wrong with it, it goes thru gears good until it gets around 50 mph with 1800-2100 rpm it starts shuddering then when I accelerate to 3000 rpm or over its good again then after awhile I go down a hill arpund 50 mph it sounds like the torque converter releases and it won't pull like the transmission is out like its in neutral or something , then I put it in neutral it whines like crazy then I stop some where and put it in park it quits then you can put it in gear and it drives good again until you go over 50 mph. Idk if it's the torque converter or the transfer case 

Posted

Probably the transmission.

 

Does anything change if you put it in manual 3rd and gain speed normally?

Posted

It kicks out in 3rd gear too until you get 3000 rpm and when I start going down a hill It starts whining  I stop some where I put it in neutral and then in  gear it just whines and whines until I put it in park. Then it's normal again 

Posted

Now if you keep it around close to 3000 rpm it won't do it it won't even shudder but when you put down to 1800 rpms and barely touch the gas it will start shuddering and it will kick out and whines and if put in neutral sometimes and it just whines like crazy then I put it in gear it still whines then I have stop some where I'll have it stopped and it still whines neutral or in gear until you put in park then it's fine again 

Posted

If both 3rd and 4th have problems, then it's internal and will likely need a new one or get it rebuilt.

 

A local transmission shop can do a diagnostic check on and it and I bet they will tell you to get it rebuilt.

 

A reman transmission is a decent chunk of money but they carry a 3 year warranty with like 100k miles.

Posted

When it starts whining why does it still whines when it's stopped in gear or in neutral after you put it in park it stops then it's good 

 

Well its been rebuilt once 5 or 6 years ago 

Would a $1600 ranufactured trans like movers on autozone be alright it's got a 3 year warranty 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Are you playing Slide Down endlessly but your score is still low? Are you constantly crashing into obstacles as the game speed increases? Don't worry, this article will share 5 invaluable tips to help you master the race and impress your friends. Golden Rules 1. Look one step further. The mistake of 90% of new players is only staring at their character. The secret of experts is to look towards the top of the screen (where the slide is about to appear). This gives your brain an extra 0.5 - 1 second to process the situation and determine the direction of movement before the obstacle approaches. 2. Use gentle movements; don't swipe too hard. Slide Down is very sensitive. Moving your finger too forcefully or with excessive amplitude will cause your character to be thrown off course or crash into a wall. Practise moving your finger with small, decisive, and precise movements. 3. Don't be greedy for gold in dangerous locations. Gold coins are tempting for buying skins, but life is more important. If you see a gold coin right on the edge of a cliff or next to a spike trap, ignore it. Our goal is a High Score, and your score only increases if you survive. 4. Make the most of Power-ups. During the slide, you'll encounter items like Magnets (attract gold) or Shields (temporary invincibility). Never miss them! Especially the Shield, it's your "get out of jail free card" to help you get through those deadly fast sections. 5. Stay calm when speed peaks. When your score exceeds 500 or 1000, the game speed will be very fast. At this point, don't try to think logically; let your natural reflexes work. Take deep breaths and don't panic. Apply these 5 tips to your next game, and your leaderboard will surely improve dramatically. Good luck climbing the Slide Down leaderboard!
    • If you use compressed air regularly, one problem you cannot ignore is moisture. Water in the air line can cause rust, unstable air pressure, poor tool performance, and even damage to sensitive equipment. That is why I highly recommend using a desiccant air dryer. A desiccant air dryer is designed to remove moisture from compressed air by using drying materials such as activated alumina or molecular sieve. Compared with basic water separators, it can achieve much lower dew points, making it especially useful for applications that require dry and stable air. For workshops, painting systems, pneumatic tools, CNC machines, laser cutting equipment, and industrial production lines, a desiccant air dryer can make a big difference. It helps protect equipment, improve air quality, reduce maintenance costs, and extend the service life of the whole compressed air system. Another advantage is reliability. Many desiccant air dryers are built for continuous operation and can maintain stable drying performance even in demanding environments. For users who care about long-term efficiency and equipment protection, this is a smart investment. When choosing a desiccant air dryer, I suggest paying attention to air flow capacity, working pressure, dew point performance, regeneration method, and maintenance requirements. A good model should match your compressor system and actual air consumption. Overall, if moisture is causing problems in your compressed air system, a desiccant air dryer is definitely worth considering. It is practical, efficient, and highly useful for anyone who needs clean, dry, and reliable compressed air.
    • My brand new 2007 Silverado's wax frame was rust from end to end partway through it's SECOND winter here in MA. That stuff is completely useless.    
    • I went another direction after losing a trailer tire, thanks to not being able to access air at ANY of the 5 gas stations and garages I stopped at prior, with a Toyota Tacoma onboard, 50 miles from the Canadian border. They were either out of order, access was blocked, or the hose a few feet too short and I couldn't get any closer without risking damage to someone's property.   https://postimg.cc/gallery/X5QJ55w
    • I took a 12 second video on my iphone but the file is too big to upload. I will have to figure out how to extract the audio or just do another start with an audio recording. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...