Jump to content

Recommended Posts

Posted

Because I want to take the one off my 02 Silverado 4.8 Ls and put it on my 2017 Silverado 1500 LT 5.3 that's y I'm curious

Posted

Not really.

 

The y-pipe will not bolt up at all.

 

Technically the only thing you could do is chop the cat off that pipe and the exhaust on the 2017 truck, then weld the cat back into place. But it's still possible that the 2002 cat converter does not do enough for the much newer emissions requirements on the 2017 truck. So the check engine light could come back on.

Posted

Is it molten or loose? Or do you have fault codes?

 

The cat should normally last until the car is gone or the converter is stolen 😀

  • Thanks 1
Posted

Check engine light blinks and when the tranny downshifts the exhaust vibrates really bad only when dropping into a lower gear it was giving me a code of engine misfire on 3 and 5 so I replaced all ignition coils on negative side all new spark plugs driver and passenger cleaned my throttle body and reset it but I haven't tried changing my 02 sensors just need some different opinions on what it might be causing my check engine to blink that's usually something serious

Posted
23 minutes ago, Victor Brown said:

Check engine light blinks and when the tranny downshifts the exhaust vibrates really bad only when dropping into a lower gear it was giving me a code of engine misfire on 3 and 5 so I replaced all ignition coils on negative side all new spark plugs driver and passenger cleaned my throttle body and reset it but I haven't tried changing my 02 sensors just need some different opinions on what it might be causing my check engine to blink that's usually something serious

 

 

What are the codes in the truck?  Not a description, but the code number.  So say its P0303.  

 

A cat y pipe would not be compatible from a 2002 to a 2017.  Different emissions requirements, different exhaust layout.  

Posted
13 hours ago, Victor Brown said:

Check engine light blinks and when the tranny downshifts the exhaust vibrates really bad only when dropping into a lower gear it was giving me a code of engine misfire on 3 and 5 so I replaced all ignition coils on negative side all new spark plugs driver and passenger cleaned my throttle body and reset it but I haven't tried changing my 02 sensors just need some different opinions on what it might be causing my check engine to blink that's usually something serious

 

That does not sound like a catalysator issue. I think you should start with a systematic fault analysis instead of just changing parts. Otherwise you probably end up wasting a lot of money.

 

As @newdude said, what are the fault codes?

Posted

I have no choice I had a full scan done and the only thing that came up was a engine misfire on cylinders 3 and 5 and I was told to change the ignition coils and wires so that's what I did but the engine light keeps coming on and blinking from my experience that indicates a bad cat maybe I should perform a smoke test to see if there is a vacume leak somewhere just hoping someone out there might of encountered something similar

 

 

 

Posted

A blinking Check Engine Light indicates only misfires. Nothing todo with the catalytic converter.

There are a lot of reasons for misfires. Bad plugs, bad ignition coils, low fuel pressure, bad injectors, broken valves, lifters, compression issues and so on.

I really think you should perform a step by step fault analysis.

Posted

I thought this was a place we bounce ideas off of each other y am I being questioned like I don't know what I'm talking about instead of telling me where you think I'm wrong which I'm not try helping me out it has everything to do with the cat for example what steps would you take if you had a deep scan of your vehicle done and you came up with one code so you think you have the problem pinpointed well after repairing all areas that have to do with that code your problem still exists what would you all do that's all I'm here for advice not who's wrong or who's right

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,972
    Total Members
    8,960
    Most Online
    Whit.the.COB
    Newest Member
    Whit.the.COB
    Joined
  • Who's Online   4 Members, 0 Anonymous, 1,242 Guests (See full list)

  • Latest Articles

  • Posts

    • I did the new thermostat after doing a 'flip' for a year. Runs as cool one way as the other in the summer but in the winter there is a bit of a floor. Yellow with the new 70 C thermostat. My data over the life of the unit to date. Still need more cooler. Anyway that floor helped both winter fuel economy and shift quality in the winter. I found it a good balance.       
    • Evan Williams Bottled in Bond   So pouring the last of a bottle of Evan Williams Black label last night I set off the the state store for a refill only to be denied the by an empty shelf. Rats.    What the did have was a bottle of Evan Williams Bottled in Bond. 100 proof. Hum, a few bucks more but a known distiller. Lets have a swing at it. ( I have before )    Cracked it open and pour a serving over ice. Hum.... more heat, yes. More alcohol naturally. But the barreling not the proof brings the taste and this one came up short.    Oh is was familiar but the heat ran the barrel over like a Peterbilt runs over a squirrel. Could use a heavier toasting of the oak me thinks or perhaps a longer barreling. Who knows. But what I can say is ice or a water back isn't the answer. What kills one kills them both. Sad. It is a pleasant drink....if you have little to compare it to.  
    • I've had exactly one set of Bridgestone. Lasted five year and 125,000 miles and had I known better 15oK would have been a cake walk. I would have bought a like set had they not tripled in price since the first set. I removed them at said mileage with 5/32" remaining in dead even wear all four. They were fuel efficient, quite, comfortable and predictable.    Early on I got a very good alignment checked at least once a year, sometimes twice; kept the tires properly inflated, balanced and rotated. And I've found that many a tire issue can be avoided with great maintenance practices. Lot's of tire dealers will do rotation and balance (simple) for free for as long as you own the tire they sold you so no excuse not to.    Bead prep, alloy integrity and stem health have a huge impact on inflation stability. There are more mountings done poorly that perfectly. Finding a good tire guy is gold and as important as finding a tire you like.    That 3X price increase now two sets of "other tires' later is starting look like a bargain.      Bad maintenance kills more tires than bad tires. 
    • Atlas, you kill me As aggravating as a project like this can be you have been unable to hide your fascination with learning and using that angst against this beast like a Ninjitsu Master. It amuses you, admit it now.      BTW, love your writing style. 😉       
    • I gotta say, I'm enjoying your narration. The troubles you've been having are amusing as you describe them. It's good to see that you're finally getting some satisfaction out the old beast though.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...