Jump to content

Transparent Trailer Camera Calibration

bruceb58
 Share

Recommended Posts

bruceb58 Enthusiast

bruceb58

Posted
Posted

Installed my factory camera at the precise location on the back of my 25' trailer and angle was set to spec. Went into setup and it won't finish calibration. I have gone 5 to 10 miles down perfectly straight roads doing slightly less than 30 MPH.

 

Any suggestions of what I might need to do to get this to finish calibration?

 

 

bruceb58 Enthusiast

bruceb58

Posted
  • Author
Posted (edited)
1 hour ago, MTU Alum said:

Can you select the transparent view or is it grayed out?  If grayed out, is your height dimension over 118 inches?

It's not grayed out and I just read the other thread about this talking about the 118 inches. Going to try lowering my height. Says on my display the max is much higher though.

 

EDIT: I may have already changed it from 123 inches to 118 inches before looking at the selection.

Edited by bruceb58
bruceb58 Enthusiast

bruceb58

Posted
  • Author
Posted
1 hour ago, MTU Alum said:

If you drive forward and select the transparent view, do you get a calibration status bar at the bottom of the screen?

 

 

I haven't looked at that screen while doing the calibration. Going to try it tomorrow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Coastie05
      Casey from the Texas Hill Country

      By Coastie05 · Posted

      Enjoy the new truck, it’s a beauty. I’m glad you’re keeping the OBS, I love those old trucks. 
    • chris21
      Towing In Loose Gravel

      By chris21 · Posted

      With large equipment or deep mud it is more of a use the higher gear to avoid spinning tires, getting stuck because of spinning tires and doing damage to your machine. The idea is if you run out of torque before you spin tires you can still downshift for more torque. If you are just spinning your tires in the lowest available gear you are stuck and things break.   Automatic transmissions, traction control and electronic transfer cases change the calculation a little as you the driver have less control over each piece. 
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      are there any codes? with lots of rust, perhaps disconnect/clean both sides of the connection/examine cable ends (the wires) for corrosion going into the sheath & replace if necessary/reconnect ALL the power AND ground cables between the battery, engine, frame, cab, fuse box and starter charm.li (website) has a no-start diagnostic procedure you can work through to get it working.
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...