Jump to content

Recommended Posts

Posted

2020 Sierra 1500 SLT. 

According to the indicator on the cluster, the right front parking assist sensor keeps beeping over nothing being there. It goes to instant red alert. I could be pulling up to a stop sign or going through a parking lot or what not, and it will screech at me worse than my ex wife and her nagging. 

The further right front sensor is a little jiggly, maybe a 1/16th of an inch, but I did shove a piece of paper in there to stabilize it, only to be met with same results. 

 

Not sure if there is a way to reset the things. I have been trying to find a manual but I guess they dont make them anymore.  

Just bought the vehicle and it is outside warranty.  

Anyone know how to diagnose or reset or know what is going on. I like the feature since I am new to driving a huge truck (they used to be so much smaller back in the day, i miss those days), so parking assist is a little helpful as I readjust my depth perception on the Tank. 

Posted

Similar issue here, went from that to just the entire system turning off due to that one sensor throwing an error. I found that if its cold, it works, but if it's warm, it errors out. 

Took it to the dealer and paid the diagnostic fee, they said that one sensor is faulty and needs to be replaced, no further detail. Part itself isn't too bad, but the labor to get to it is expensive. Some good youtube videos about replacing the sensor, it looks like you have to remove the entire grill / bumper assemply.

 

  • 4 weeks later...
Posted

We've had sensors replaced in the front bumper and now its back at the dealer supposedly having a rear sensor(s) replaced for a similar issue.  Our park assist system will suddenly say "unavailable" in the cluster and the toggle in the center stack becomes unresponsive and without an orange light.  No rhyme or reason as to when it happens, but its never when dirty, wet, or covered in ice as the dealer and GM have tried to push as explanations.  

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,993
    Total Members
    8,960
    Most Online
    President Roberto
    Newest Member
    President Roberto
    Joined
  • Who's Online   0 Members, 0 Anonymous, 173 Guests (See full list)

    • There are no registered users currently online
  • Latest Articles

  • Posts

    • I don't wanna do major surgery/upgrades, behind-the-dash work, add amps, change radio etc. on my '26 std cab WT. On the WT, it has the base 7" IOR infotainment setup, and only two speakers (doors). Since I listen to classical, looked around for speakers that do well and dug thru reviews. Two-way speakers were found to be better than 3-way. So I've ordered a pair of  Infinity Reference REF-9632IX 2 way speakers.  [These may  or may not have been discontinued / succeeded by the 3-way ...9633 ones.]    These speakers are lauded for 3 ohm and 94db sensitivity spec so they'll work well for ordinary base car radios without amps and offer better performance (quality,  strength) than  default base paper-cone speakers. They'll be installed in a few days and I'll let y'all know what I think. Bill W San Jose      
    • Thanks!   Changed out the rear shocks today to Bilstein 5100s.  So far feel much better. The stock Rancho were wore out.  Lots of heavy hauling (2 moves, home renovations, etc).  Next up is new BFG tires Monday.  Cant wait the current tires have little to no wet traction and are super loud (hum)    
    • Ok, I got the all the codes. What do you all think would be a place to start?
    • How about I just point to the factory pans stand pipe little drain plug and claim its a pan with a real drain plug !. I just couldn't swallow the fact that a Dorman pan which at this point is probably the only pan out there that fits the gas version truck cost that much up here in Canada so I decided initially anyway to skip it and see what I thought of pulling the pan method and down the road if I felt inclined enough then I would either install a drain plug kit in the factory pan if there is enough room for it, or have a bung welded onto it, or put an aftermarket pan on. The thing is if the pan is not pulled then the magnets in the pan can't be inspected and cleaned or if wanting to change out the filter. However of course it certainly would make the job easier to be able to drop the oil first before having to handle the pan if dropping the pan that go around was the goal.    I knew a guy locally that was doing custom field spraying years ago with a pickup pulling a ground driven sprayer, I believe it was a GM pickup with an automatic trans. He had a drain plug in his pan and would drop the oil out of it once a week and top it back up through the dipstick tube to keep refreshing a portion of the oil often and that made the transmission last far longer than had he done nothing. Soft fields pulling 500 gallons of water at the start of each mixed up sprayer tank batch and in low range sucking along. I imagine he got some tips from other custom sprayer outfits doing the same thing at the time and learning from their blown up tranny mistakes. Transmissions then had no lock up converter so would cook the crap out of the fluid slipping that much and it would not have been synthetic fluid either. 
    • 3.39 Kroger’s in Montgomery Texas. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...